• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.325-332
• /
• 2003

In general, soil characteristics are estimated through the sample gathered by field boring without considering sample disturbance. However, soil characteristics must be changed by the degree of sample disturbance. Therefore it be need to estimate the soil characteristic considering sample disturbance which can be occurred by the change of stress condition, sampling technique and handling method. On this study, we analyzed the sample disturbance by using the methods of volume change, residual effective stress, elastic modulus and the curve of consolidation tests. In order to estimate the relationship between sample disturbance and soil characteristics, we used the piston sample and the block sample. As the results, it should be considered in design that the disturbance of the block sample, which affects the strength and compression properties of clay, is smaller than the disturbance of piston sample.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.127-129
• /
• 1996

A 3-dimensional analysis is desired for a magnet of magnetically levitated vehicle because the geometrical shape of the magnet is complicated and nonsymmetric. A FEM package of FLUX3D is used to analyze the characteristic of the magnet. Various quantities could be observed like levitation force, flux density distribution along the air gap, edge and fringing effect, leakage flux pattern, etc. The simulation results from FLUX3D are compared with those of 2-D analysis and test results. There are a little difference between results due to the boundary conditions and magnetized B-H curve of the core.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.265-272
• /
• 2000

This study introduces the current theory of the SWCC and tries to verify the theory by performing laboratory tests for the local soils of Korea. First, the SWCCs of Poi-dong soil and Shinnae-dong soil, the most typical weathered residual soils in Korea, were experimentally obtained and the results were compared among others. Second, a SWCC model for deformable soils was proposed. For deformable soils, which show huge volume change during desaturation, the volume change behavior should be considered, and the SWCC should be expressed as a function of void ratio as well as suction.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1598-1603
• /
• 2004

This paper is an experimental study on the performance characteristic with a variation of capillary diameter and length. The performance characteristic of a refrigeration system is predicted that it is occurring changes of flow pattern and pressure drop in a capillary tube because of reduction of capillary diameter 0.74 to 0.6 mm. The difference between experimental results and analytical results is mainly caused by values of friction factor for using to calculate pressure drop through a small diameter capillary tube under 0.74mm. The experimental equation is derived from capillary tube test data using curve fitting method.

• Korean Journal of Digital Imaging in Medicine
• /
• v.12 no.1
• /
• pp.65-69
• /
• 2010

High energy electron beams were to concentrically dose inside a tumor and more energy is a shape decreased of dose. Therefore, it is useful to radiation therapy of a tumor. Also high energy electron beams ionized into collision with a atom in structure material of tissue and it has big changes to dose distribution by multiple scattering. The study had to establish characteristic of electron beams from interaction of electron beams and materials. Experiment method was to measure dependence of electron beam central axis for depth dose curve, field flatness and symmetry and field size dependence. The results were able to evaluate data for a datum pint of electron beam. Also radiotherapy has to be considered for not only energy pencil of lines but characteristic, electron guide and isodose curves distribution.

• Journal of the Korean Society of Safety
• /
• v.21 no.4 s.76
• /
• pp.49-54
• /
• 2006

The evaluation of elastic-plastic fracture characteristic was investigated in ferrite steel SA 516- Gr70 used for reactor coolant piping elbow and support skirt of pressure vessels. This paper describes the effect of temperature on J-R curve characteristic of this material. The elastic-plastic fracture mechanics parameter J is obtained with unloading compliance method. The test method were analyzed according to ASTM E 813-89 and E 1152-89. Unloading compliance $J_{IC}$ tests were performed on 1 CT specimens at varied temperatures from $25^{\circ}C$ to about $400^{\circ}C$ using a high temperature extensometer. At all temperature, valid $J_{IC}$ measurements could be made and $J_{IC}$ decreased with increasing temperature. SEM fractography schematically illustrates microvoid initiation, growth and coalescence at the tip of a preexisting crack.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2017.10a
• /
• pp.88-92
• /
• 2017

As the considerable request of the fast and accurate way of the selection of circuit breaker is increased, we introduce the development of software of circuit breaker selection for the marine use. Originally, the selection of circuit breaker has been carried out by manual in the marine project. It is not the easy work to select the proper type of circuit breaker to check the time-current characteristic curves of each type of circuit breakers for the various type of loads. In this regards, we developed the software to select the proper type of circuit breaker to confirm fast and accurately. And, we introduce the course of the development of the software for the selection of circuit breaker.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.1
• /
• pp.165-170
• /
• 2015

In this paper, The strength and driving characteristics of it were investigated according to developing the traction motor for 8200 electric locomotive series. For this purpose, Flux density strength was analyzed and then structural strength was investigated such as a stator frame, design of the rotor shaft bearing according to the design process. In addition, the traction motor operating point was analyzed according to slip frequency variation at a power source frequency. As the results of analysis on torque-speed characteristic curve, we was confirmed that traction motor was controlled as torque control prior to motor speed 1610[rpm], power control between 1610[rpm] and 2500[rpm] and breakdown torque control more than motor speed 2500[rpm].

• Journal of applied mathematics & informatics
• /
• v.30 no.1_2
• /
• pp.101-109
• /
• 2012

In this paper, we present an algorithm for computing the number of points on the Jacobian varieties of one-dimensional family of genus 3 nonhyperelliptic curves over finite fields. We also provide the explicit formula of the characteristic polynomial of the Frobenius endomorphism of the Jacobian of $C:y^3=x^4+{\alpha}$ over a finite field $\mathbb{F}_p$ with $p{\equiv}1$ (mod 3) and $p{\neq}1$ (mod 4). Moreover, we give some implementation results using Gaudry-Schost method. A 162-bit order is computed in 97 s on a Pentium IV 2.13 GHz computer using our algorithm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.914-922
• /
• 2003

In this paper, the strain localization of voided ductile material has been analyzed by nonlocal plasticity formulation in which the yield strength not only depends on an equivalent plastic strain measure (hardening parameter), but also on the Laplacian thereof. The gradient terms in yield criterion show an important role on modeling strain-softening phenomena of material. The influence of the mesh size on the elastic -plastic deformation behavior and the effect of the characteristic length parameter for localization prediction are also investigated. The proposed nonlocal plasticity shows that the load -strain curves converge to one curve. Results using nonlocal plasticity also exhibit the dependence of mesh size is much less sensitivity than that for a corresponding local plasticity formulation.