• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.933-935
• /
• 2005

This study investigates Characteristic analysis of Line-start Synchronous Reluctance Motor to substitute for Induction Motor. The results of machine characteristics are analyzed by simulation using Flux2D. Characteristic analysis result of Line-start Synchronous Reluctance Motor is confirmed by the analysis result of 3-Phase Induction Motor.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.160-165
• /
• 2004

In these days, the people living in the urban is suffer from the environmental noise because the number of car increase in the city, and a lot of new industrial complex is made in the urban every. But there is no suitable system for measurement and management of environmental noise. Therefore, in this research, a new system for the measurement, characteristic analysis and evaluation, management of environmental noise using Internet communication is developed. The system includes the environmental noise measurement equipment and the controller for the noise measurement, analysis and evaluation, management.

• 융합신호처리학회논문지
• /
• 제7권4호
• /
• pp.214-220
• /
• 2006

This paper presents the systematic isotropy analysis of a fully actuated caster wheeled omnidirectional mobile robot (COMR) with the steering link offset different from the wheel radius, which can be considered as the generalization of the previous analysis. First with the characteristic length introduced, the kinematic model of a COMR is obtained based on the orthogonal decomposition of the wheel velocities. Second, the necessary and sufficient conditions for the isotropy of a COMR are derived and examined to categorize there different groups, each of which can be dealt with in a similar way. Third, for each group, the isotropy conditions are further explored so as to identify four different sets of all possible isotropic configurations. Fourth, for each set the expressions of the isotropic characteristic length required for the isotropy of a COMR are elaborated.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.157-164
• /
• 1995

Straight belvel gear is used mainly for steering system, final reduction and differential gear in the automobile. The more high load, high velocity driving bevel gear, the more unsafe and unpleasant. In thid study, we get a kinematic equation by modelling straight bevel gear pair with simple elastic system, the dynamic characteristic analysis about this system, we got the dynamic load factor of tooth surface. Comparing the value of dynamic load factor by calculation with the measured value of Terauchi's experimental results is similar. We think it useful to analysis the vibration and the noise of straight bevel gear in operation with the analytic method of dynamic load of straight bevel gear using in this study.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.808_809
• /
• 2009

This paper deals with the dynamic characteristic analysis on Linear Induction Motor(LIM) considering load conditions. The analysis on the electromagnetic characteristics is processed to derive circuit parameters, and dynamic modeling for the analysis is performed considering load conditions for speed and thrust dynamic characteristics.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 제18회 학술대회 초록집
• /
• pp.63-69
• /
• 1993

In this paper the characteristics of Hydrostatic Bearing of piston of cylinder are investigated . The dynamic characteristic equations of piston considering both parallel and rotational motion and time dependent modified Reynolds Equation are analyzed and the dynamic pressure distribution of oil film is numerically calculated by perturbation method and finite difference method. and the atatic analysis is carried out. so, the influence of design parameter of piston on the characteristic of bearing is analyzed.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.437-442
• /
• 2005

This paper deals with the measurement and analysis of radio characteristic of 424 MHz for using the automation of transmission and supply of electric power, ana automatic meter reading(AMR). Normally radio propagation characteristic is the base of system design, performance evaluation and choice of position of the base station in wireless communication. It is the most accurate way to design a base station through practical measurements, but it costs much time, money and engineers. So, we developed 424 MHz short range wave propagation model for AMR service.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.403-408
• /
• 2007

According as diesel automobile are produced, reduce noise and vibration that is occurred by characteristic of diesel engine, and need engine room layout optimization and research for light weight of parts. Balance Shaft Module is module parts for vehicles engine to improve performance and efficiency of engine and reduce noise and vibration. These days, an oil pump integrated balance shaft module and an oil sump integrated balance shaft module is on the rising for optimizing of engine room. In this study, produced prototype of oil pump integrated type balance shaft module, and achieved dynamic characteristic test about experimental modal analysis and noise/vibration of balance shaft module.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.943-946
• /
• 2007

The vibration and noise characteristic of the Axial-gap motor for an air conditioner were analyzed. Experimental Modal Analysis was performed to understand the vibration characteristic of the motor. The noise of motor was measured in a dead room. Finite Element Method was performed to find the vibration characteristic of the motor by using ABAQUS program.

• 전기학회논문지
• /
• 제56권4호
• /
• pp.699-704
• /
• 2007

In this paper, optimized model was designed for the starting characteristic of the Single-Phase Line-Start Permanent Magnet Synchronous Motor by using the Design of Experiment. A field pole angle, thickness and distance from center axis of permanent magnet were selected as design factor. We executed the transient state characteristic analysis of 8 test models. The transient state characteristic analysis was executed by using the 2 dimensional Finite Element Method and the Time Difference Method. We checked the fact that the selected design factor affected starting characteristic of the Line-Start Permanent Magnet Synchronous Motor. Depend on this result we found the optimized design point by using the response optimization.