• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.811-814
• /
• 2002

Using a mathematical theory, we show that the optimality condition of a turbulent diffuser with maximum pressure recovery at the exit is zero shear stress along the wall. The optimal diffuser shape is designed through iterative procedures by using the $k-{\varepsilon}-{\nu}^{2}-f$ turbulence model for flow simulation. The Reynolds number based on the bulk mean velocity and the channel height at the diffuser entrance is 18,000. We also perform large eddy simulation to validate the shape design results and investigate the flow characteristics near the zero-skin friction wall. Results from large eddy simulation show that the skin friction is slightly higher than zero but is still very small as compared to that of the flat plate boundary layer flow Although the time-averaged wall shear stress is slightly above zero along the diffuser wall, instantaneous flow reversals occur intermittently. The streamwise mein velocity shows an asymptotic behavior of the half-power-law near the wall where the skin friction is close to zero.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.514-517
• /
• 2008

An hydraulic experiment was carried out in an open channel flume in order to investigate the water discharge capability of the sluice caisson for tidal power generation, which greatly affects the economical efficiency of the construction of a tidal power plant. To predict the influence of change in the major design parameters relating to the sluice shape on the water discharge capability of the sluice, the experiment was carried out very precisely. The experiment was carried out for the six different sluice models of different widths and bottom heights of the sluice throat section. The experimental data showed that the water discharge generally increased by increasing the width of the throat section if the side shape of the sluice was the same. In addition, the coefficient of discharge was larger when the bottom height of the throat section was higher for the two bottom heights that were tested.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.331-340
• /
• 1994

Polysilicon on insulator has been recrystallized by zone melting recrystallization method with graphite strip heaters. Experiments are performed with non-seed SOI structures. When the capping layer thickness of Si$\_$3/N$\_$4//SiO$\_$2/ is 2.0.mu.m, grain boundaries are about 120.mu.m spacing and protrusions reduced. After the seed SOI films are annealed at 1100.deg. C in NH$\_$3/ ambient for 3 hours, the recrystallized silicon surface has convex shape. After ZMR process, the tensile stress is 2.49*10$\^$9/dyn/cm$\^$2/ and 3.74*10$\^$9/dyn/cm$\^$2/ in the seed edge and seed center regions. The phenomenon of convex shape and tensile stress difference are completely eliminated by using the PSG/SiO$\_$2/ capping layer. The characterization of SOI films are showed that the SOI films are improved in wetting properties. N channel SOI MOSFET has been fabricated to investigate the electrical characteristics of the recrystallized SOI films. In the 0.7.mu.m thickness SOI MOSFET, kink effects due to the floating substrate occur and the electron mobility was calculated from the measured g$\_$m/ characteristics, which is about 589cm$\^$2//V.s. The recrystallized SOI films are shown to be a good single crystal silicon.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.3
• /
• pp.173-179
• /
• 2016

This is a numerical study on the curved channel type of hydrogen reformer using the commercial code of fluid dynamics. We numerically compared the numerical model in a previous study model and the modelling of a tube type curved channel. In the result of numerical analysis on 4 types of curved channel reformers, the methanol conversion efficiency of type 1~4 were 45.0%, 45.3%, 45.6%, 45.6% respectively, and there was hardly any difference by ${\pm}0.6%$. In light of flow characteristics, the rectangle type tube and the type 2 with $45^{\circ}$ turn showed most uniform flow characteristics and concentration distribution of methanol, and the circular type tube and the type 3 with $90^{\circ}$ turn had most un-uniform flow characteristics and concentration distribution of methanol. We concluded that the design for curved channel reformer has to have rectangle type tube with curve of almost $45^{\circ}$ as in the type of curved pipe with $45^{\circ}$ turn.

• Journal of Korea Water Resources Association
• /
• v.46 no.9
• /
• pp.947-956
• /
• 2013

Most of flood protection walls built on the impingement in mountain rivers have been made of concrete. It may cause flood disasters because the smooth wall surface could increase flow velocity. In this study the hydraulic experiments was carried out to evaluate the effect of one side wall with rectangular vertical ribs on flow resistance in open channel. The ratio of the pitch between vertical ribs to its depth, ${\lambda}_{nv}$, was designed so that it include the so-called d type and k type roughness. The range of Froude number, $F_r$, based on hydraulic radius is 0.81~1.12. Flow resistance in the open channel with a rib sidewall depends on the interval length of each ribs and the flow discharge. Maximum flow resistance occurred when ${\lambda}_{nv}$ is 9. In the d type roughness which ${\lambda}_{nv}$ is less than 3, the flow resistance decreases with increase of flow discharge. In the k type roughness which ${\lambda}_{nv}$ is greater than 3, the flow resistance increases with increase of flow discharge. The increments of flow resistance are especially great when ${\lambda}_{nv}$ are 9 and 12. The resistance due to vertical rib is mostly by the shape resistance and the vertical rib on one sidewall of open channel affects on the flow resistance so that the equivalent roughness heights of vertical rib may occur in scale of flow depth. Therefore the vertical ribs may be used to reduce the flow velocity and to move the location of maximum flow velocity from the rib sidewall to the centerward in a cross section of channels.

• Journal of Biomedical Engineering Research
• /
• v.43 no.5
• /
• pp.331-340
• /
• 2022

Early afterdepolarization (EAD), a significant cause of fatal ventricular arrhythmias including Torsade de Pointes (TdP) in long QT syndromes, is a depolarizing afterpotential at the plateau or repolarization phase in action potential (AP) profile early before completing one pace. AP duration prolongation is related to EAD but is not necessarily accounted for EAD. Several computational studies suggested EAD can form from an abnormality in the late plateau and/or repolarization phase of AP shape. In this sense, we hypothesized the slope during repolarization has the characteristics to predict TdP risk, mainly focusing on the maximum slope during repolarization (dVm/dt_{max_repol}). This study aimed to predict the sensitivity of dVm/dt_{max_repol} to ion channel conductances as a TdP risk metric through a population simulation considering multiple effects of simultaneous reduction in six ion channel conductances of g_NaL, g_Kr, g_Ks, g_to, g_K1, and g_CaL. Additionally, we verified the availability of dVm/dt_{max_repol} for TdP risk prediction through the correlation analysis with qNet, the representative TdP metric. We performed the population simulations based on the methodology of Gemmel et al. using the human ventricular myocyte model of Dutta et al. Among the sixion channel conductances, dVm/dt_{max_repol} and qNet responded most sensitively to the change in g_Kr, followed by g_NaL. Furthermore, dVm/dt_{max_repol} showed a statistically significant high negative correlation with qNet. The dVm/dt_{max_repol} values were significantly different according to three TdP risk levels of high, intermediate, and low by qNet (p<0.001). In conclusion, we suggested dVm/dt_{max_repol} as a new biomarker metric for TdP risk assessment.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.1
• /
• pp.146-153
• /
• 2015

A model net experiment of the gape net for anchovy in Jindo, Jeollanam-do was carried out to investigate the net shape and hydrodynamic resistance using circulating water channel. The model net was made 1/33 down scale by Tauti's similarity method and the range of experimental current speed was from 0.5 knot to 3.5 knot (increasing 0.5 knot interval). The net mouth height in 0.5 knot of the minimum experiment current speed was shown 26.0 cm (full-scale conversion value 8.58 m). The net mouth height and mouth area in 1.5 knot of the same current speed with a gape net fishing ground were shown 20.0 cm (full-scale conversion value : 6.60 m) and about $507.9cm^2$ (full-scale conversion value : $55.31m^2$). The net mouth height and area were decreased with increase the experimental current speed. The hydrodynamic resistance of the model net in 1.5 knot current speed was shown 1.11 kgf and the value of full-scale conversion by Tauti's method was shown 3.996 ton.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.4
• /
• pp.347-357
• /
• 2013

Recently, In recognition of outstanding structural performance the use of Concrete Filled steel Tube(CFT) columns has been increased. Research is ongoing that effective use of cross-sectional because steel strength development and rising prices. In this Lab, suggests new shape by Thin steel plates bent to be L-channel welded to form square steel tube to maximize efficiency of the cross section. In addition, since the rib placed at the center of the tube width acts as an anchor; higher load capacity of buckling is acceptable. we have developed New shape welded built-up square tube for broader usability which were bent to be L-shaped and thin Plate each unit member were welded. In order to apply the new shape built-up square columns, we predicted structure behavior, stress distribution with parameter Width thickness ratio. The experimental results presented in standards and even exceed the b/t of the rib anchors installed in the role due to exert enough strength and deformation to improve performance was favorable.

• Journal of the Korean Institute of Oriental Medical Informatics
• /
• v.15 no.2
• /
• pp.77-91
• /
• 2009

Flowery Knotweed Root is the dried tuberous root of the knotweed family wheres Auriculate Swallowwort Root is the dried tuberous root of the swallowort family. Flowery Knotweed Root is also called Red Flowery Knotweed Root in China, which is dried root of Polygonum multiflorum THUMB. Chinese Flowery Knotweed Root is better known as the dried tuberous root belonging to the family Apocynaceae whereas White Flowery Knotweed Root in Korea is the dried tuberous root of Cynanchum wilfordii(Maxim) Hemsl. Up to now, while the dried root named Red Flowery Knotweed Root has been widely used in China, Auriculate Swallowwort Root has been widely used in Korea. Both the roots contrast in a striking way with the origin, shape, botanical names, other names, and chemical constituents, so administration and dosage without discrimination of both sides can be open to question. According to the literature, it is recorded that Flowery Knotweed Root and Auriculate Swallowwort Root are similar to the characteristics, properties, and actions. From this study, the result is as follows: 1. Flowery Knotweed Root and Auriculate Swallowwort Root are divided into the family Apocynaceae and the family Polygonaceae, respectively. Accordingly 2. Flowery Knotweed Root is in shape of an irregular spindle and looks reddish- brown or deep reddish-brown and the section is light yellowish-brown, while Auriculate Swallowwort Root looks yellowish-brown and the section is white or yellow. 3. Flowery Knotweed Root is reported by the Journal of the Crude Drug that the medicinals have not the same therapeutic action as Auriculate Swallowwort Root. It is recorded that the properties, channel entry, functions of Flowery Knotweed Root and Auriculate Swallowwort Root in literature have much in common. Many works on the roots of this plant has been used traditionally as a tonic are required of. In view of the results, Flowery Knotweed Root and Auriculate Swallowwort Root varies both in nature and in shape, so that the administration and dosage of the medicinals must be taken a prudent attitude.

• Journal of Korea Multimedia Society
• /
• v.3 no.4
• /
• pp.333-338
• /
• 2000

MPEG2(or some situations, MPEG is mostly used to change the raw image into the compressed bitstreams for digital image processing. Also these bitsreams are stored in computer for several applications such as multimedia area. Transmission channels have various capacities according to the application area, and the bitstreams stored in computer should be converted in order not to exceed the capacities of a transmission channel. So the problem is how to convert compressed bitstreams of a given bit-rate into compressed bitstreams of other bit-rates. Such a specific transcoding problem in this paper is referred to as bit-rate conversion. Several researches have been done on bit-rate conversion for the bitstreams compressed by MPEG. But the existing schemes are not suitable fort MPEG4 applications because it needs to transmit shape information( which is not necessary for MPEG2) as well as texture information in MPEG4 system. So we propose a new bit-rate converter which considers both texture and shape information.