• 한국주조공학회지
• /
• 제13권1호
• /
• pp.42-49
• /
• 1993

Conventional manufacturing process for cast iron-babbitt metal composite is complicate and bimetallic bonding by centrifugal casting is also difficult because their melting point is largely different and nonmetallic inclusion exists on outer shell. This study is aiming to simplify multistage process by adding Cu-powder as insert metals during cast iron solidification. The variables on fabrication of composite pipe are mold rotating speed and inner surface temperature of outer metal. The optimum temperature range for fusion bonding between cast iron and Cu-layer was $1100^{\circ}C-1140^{\circ}C$ in case of mold rotating speed was 700rpm. When the inner surface of Cu-layer was at $900^{\circ}C$, the value of interfacial hardness between Cu-layer and babbitt metal were higher than Cu-matrix by forming diffusion layer, interfacial products between Cu-layer and babbitt metal are proved to be $Cu_6Sn_5({\eta})$by XRD.

• 한국주조공학회지
• /
• 제42권3호
• /
• pp.153-160
• /
• 2022

초내열합금 625 튜브의 제조에 필요한 원심주조품의 두께에 따라 응고조직과 기계적 특성에 미치는 영향을 고찰하였다. 10, 17, 50 mm 두께로 원심주조한 625합금에서 두께의 증가에 따라 주상정 부분의 길이와 2차 수지상 간격이 약간 증가하였으나 상온 인장특성은 큰 차이를 보이지 않았다. 주상정 부분의 응고는 일방향응고의 형태로 응고가 진행되기 때문에 일방향응고 조건을 변화시켜 2차 수지상의 간격을 비교하여 각 두께의 주조품에서 응고속도를 계산하였다. 두꺼운 주조품일수록 내부 다결정 조직의 비율이 증가하였다. 다결정 부분의 인장특성은 주상정 부분의 평균값과 유사한 값을 보였으며 이는 2차 수지상의 간격보다 결정립 형태의 영향인 것으로 사료된다.

• 한국주조공학회지
• /
• 제29권2호
• /
• pp.78-85
• /
• 2009

Functionally graded microstructure of centrifugal cast Al-Si alloy, especially distribution of primary Si particles according to the changes of melt pouring temperature and rotation frequency was investigated by numerical simulation. Moving velocity of Si particles increased as the melt pouring temperature and rotational frequency of mold increased. Therefore, segregation tendency of primary Si particles toward inner side of cylindrical sample increased as the melt pouring temperature and rotational frequency of mold increased. Rich distribution region of particles was located at 0.9, 0.7, 0.4 mm from inner surface of cylindrical sample under the centrifugal cast condition of $750^{\circ}C$ melt pouring temperature and 1500, 2000 and 2500 rpm mold rotational frequencies, respectively, by numerical simulation.

• 대한기계학회논문집A
• /
• 제21권9호
• /
• pp.1491-1497
• /
• 1997

The purpose of this research is to improve the surface roughness of cast-iron pipe porduced by the centrifugal casting. A twin-fluid atomizer of mold-wash slurry is designed for this project. New atomizer is equipped with the existing manufacturing facility to produce pipes. Cast-iron pipes (.cent.125*L3000mm) are produced and the surface roughnesses of those are analysed by UBM. The average surface roughness of new products is 6.7.mu.m while the old products of sand-resin coating method have 17.0.mu.m of average surface roughness. The surface roughness of cast-iron pipe is improved very much than before.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 제7회 압연 심포지엄
• /
• pp.111-114
• /
• 2009

Production of rolled steel has been growing partly supported by the advancement of rolls and rolling mills. Aiming at the further improvement in roll performance, various new techniques such as centrifugal casting, double poured casting cast steel, special build-up making, etc. have been introduced in the field of roll manufacture in these several years. The present paper describes the development of horizontal cast rolls(sleeve and indefinite chilled roll) made by Hyundai Steel and the results of mill tests. The developed roils are contributing the improvement of final products.

• 대한치과기공학회지
• /
• 제34권4호
• /
• pp.361-368
• /
• 2012

Purpose: The aim of this study was to analysis the composition on the centrifugal casting and the oxide on the casting temperature. Methods: The nickel based alloy were used in this study. Wax pattern specimens (10*10*2) were invested with phosphate-bonded investment in metal rings, the liquid/powder ratio and overall burn-out schedules for these investments were followed in accordance with the manufacturer's instructions. After casting, the alloy specimens were evaluated as regards composition(EPMA). The casting temperatures were as follows: $1400^{\circ}C$ and $1700^{\circ}C$. The quantitative analysis of oxides were scanning electron microscope(SEM), energy dispersive spectroscopy(EDS) and line scanning. Results: Nearer the injection lines showed that there is a large amount of nickel. Quantitative of oxides of Ni-Cr alloy cast from $1400^{\circ}C$ is lager than Ni-Cr alloy cast from $1700^{\circ}C$. Conclusion: Casting when using a centrifugal casting machine centrifugal force affects the composition of the alloy. The higher the temperature, the amount of oxide that is generated many.

• 한국주조공학회지
• /
• 제9권3호
• /
• pp.209-214
• /
• 1989

• 한국표면공학회지
• /
• 제37권5호
• /
• pp.296-300
• /
• 2004

The defects of partial denture frameworks are mainly shrinkage porosity, inclusions, micro-crack, particles from investment, and dendritic structure. In order to investigate a good casting condition of partial denture frameworks, the three casting alloys and casting methods were used and detected casting defects were analyzed by using electrochemical methods. Three casting alloys (63Co-27Cr-5.5Mo, 63Ni-16Cr, 63Co-30Cr-5Mo) were prepared for fabricating partial denture frameworks with various casting methods; centrifugal casting (Kerr, USA), high frequency induction casting (Jelenko Eagle, USA), vacuum pressure casting (Bego, Germany). The casting temperature was $1,380^{\circ}C$ (63Co-27Cr-5.5Mo and 63Ni-16Cr) and $1,420^{\circ}C$ (63Co-30Cr-5Mo). The casting morphologies were analyzed using FE-SEM and EDX. The corrosion test of the dendritic structure was performed through potentiodynamic method in 0.9% NaCl solutions at $36.5^{\circ}C$ and corrosion surface was observed using SEM. The defects of partial denture frameworks improved in the order of centrifugal casting, high frequency induction casting, and vacuum pressure casting method, especially, pore defects were found at part of clasp in the case of centrifugal casting method. The structure of casting showed dendritic structure for three casting alloys. In the 63Co-27Cr-5.5Mo and 63Co-30Cr-5Mo, $\alpha$-Co and $\varepsilon$-Co phases were identified at matrix and $${\gamma}$-Ni_2$Cr second phase were shown in 63Ni-16Cr. Also, the corrosion resistance of cast structure increased in the order of vacuum pressure casting, high frequency induction casting, and centrifugal casting method.

• 한국기계가공학회지
• /
• 제19권5호
• /
• pp.111-117
• /
• 2020

Centrifugal casting is suitable for producing hollow-products using centrifugal force. Bush type metal bearings are the key parts that facilitate the rotational movement of various machinery. Metal bearings produced by conventional centrifugal casting machines show rotational imbalance. Therefore, after injecting a large amount of material, the product's precision is secured in the secondary processing. Rotational imbalance is caused by the force acting on the rotary disc plate. In order to minimize rotational imbalance, NASTRAN was used for the optimal design and structural analysis. It was concluded that the rotating plate of the conventional centrifugal casting machine should be prevented from tilting. For this purpose, the location & thickness of the stiffeners were obtained through the optimum design. In the conventional centrifugal casting machine, both ends of the product are lower in temperature than the center part, so internal stress occurs. This solves this problem by inserting a heating coil into the rotating plate.

• 한국주조공학회지
• /
• 제8권4호
• /
• pp.429-436
• /
• 1988

The influences of some casting conditions on bonding ratio and state at bonding zone of stainless steel-cast iron dual tube produced by centrifugal casting process were investigated to estimate fabrication technics. 1) Bonding ratio is increasing such as increasing of inner surface temperature of outer metal(stainless steel STS 304), if pouring temperature of inner metal (cast iron) is constant. 2) The more pouring temperature of inner metal (cast iron) increase, the more bonding ratio increase when inner surface temperature of outer metal (cast iron) is constant. 3) As the mold rotary speed is increase, the hatching area of bonding map (perfect bonding area) goes down to the low pouring temperature of inner metal. 4) In order to predict bonding state of two different metal, we are able to make and use the bonding map about casting conditions such as inner surface temperature of outer metal, pouring temperature of inner metal and mold rotary speed.