• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.245-248
• /
• 2004

The press cutter is productive equipment that practically manufactures materials such as fabrics, papers, films, leathers, rubbers etc. into the desired shapes using cutting method. Plate cutting process is one of the primary energy absorbing mechanisms in a grounding or collision event. The cutting mechanism is complicated and involves plastic flow of plate in the vicinity of the tip, friction between wedge and plate, deformation of plate. In this paper, we studied the effect of friction between cutter and plastic sheet for producing precise and superior products. The press cutter is analyzed numerically using MARC finite element program according to the variation of friction coefficients. The FEM results showed that normal stress, equivalent cauchy stress, normal total strain, equivalent total strain are good when friction coefficient is 0.0 and shear stress, shear total strain are good when friction coefficient is 0.8.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.635-639
• /
• 2007

In this study, optimal design and test of flat-plate heat pipe were carried out in order to improve both thermal response and surface temperature uniformity of heating plate. Experimental results show that the thermal response of flat-plate heat pipe is faster than that of a conventional heating type ones along with less weight and cost. The surface temperature uniformity is also improved.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.2
• /
• pp.76-82
• /
• 2008

We investigated sterilization characteristics of UV lights by counting the number of bacteria units with varying sterilization time and distance from the light source. We focused on an idea that UV light of 184.9 nm could generate ozone and developed a new sterilizer. The UV-ozone duplex system sterilized bacteria faster than UV-only sterilizers. To reduce shadowing effects by target objects, we used UV transparent quartz plate as a support and put a reflecting plate. Distribution of UV irradiation intensity and ozone supply were analyzed by a 3D model and measured by a semiconductor UV sensor. But even with an Al reflector, multi-layered pens could not be treated properly from UV irradiation only. Ozone generating lamp could treat more uniformly multi-layered pens with a stirring fan by supplying ozone to shadowed surfaces.

• Journal of Korea Foundry Society
• /
• v.30 no.6
• /
• pp.235-240
• /
• 2010

The evolution of microstructure and phases of Mg-10Al-Mn alloy by cooling plate method during homogenization treatment have been investigated with metallographic analysis, scanning electron microscopy and energy dispersive spectroscopy. The ingots used for this experiment were prepared by cooling plate and homogenization heat treatment was performed at 300 and $400^{\circ}C$ for various holding times (0, 1, 4, 8 and 12h). The casting ingots were consisted of the fine grains and eutectic phases. And, these eutectic phases were dissolved into the matrix during homogenization treatment at $400^{\circ}C$ but the lower temperature (at $300^{\circ}C$) did not be.

• Proceedings of the Korean Society of Veterinary Clinics Conference
• /
• 2009.10a
• /
• pp.248-248
• /
• 2009

• Wind and Structures
• /
• v.2 no.2
• /
• pp.119-125
• /
• 1999

The ZG Bridge(preliminary design), with unfavorable aerodynamic stability characteristics, is a truss-stiffened suspension bridge, its critical wind speed of flutter instability is much lower than that of code requirement, In the present paper, based on both aerostatic and aeroelastic section model wind tunnel test, not only effects of some aerodynamic means on aerodynamic stability of its main girder are investigated, but also such effective aerodynamic means of it as flap and plate-like center stabilizer are concluded.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.940-943
• /
• 2007

The objective of the research presented in this paper is to design a highly efficient LCD-TV backlight unit (BLU) which minimizes lamp count without light leakage from the BLU. A new optical plate helps to successfully distribute spatial luminance in a 46inch LCD-BLU consisting of only 20 CCFLs.

• Structural Engineering and Mechanics
• /
• v.68 no.2
• /
• pp.261-275
• /
• 2018

A comprehensive study was provided to investigate the buckling behavior of the steel plates with and without through-thickness holes subjected to uniaxial compression using ABAQUS. The method was validated by the results reported in the literature. Using the critical stresses, the buckling coefficients ($K_c$) were calculated. The effects of inclusion of material nonlinearity, plate thickness (t), aspect ratio (AR), and initial imperfection on buckling resistance of the plate was studied. Besides, the effects of having the hole in the plate were also studied. The diameter of the hole was normalized by dividing by plate breadth and was given in the form of ${\alpha}$. Results showed that perforating one hole in the center of a plate increases the plate buckling resistance while the having two holes resulted in a decrease in the plate buckling resistance. The effects of hole eccentricity (Ecc) on the buckling resistance of the plate was studied. The position of the hole center was normalized by half of the plate breadth and length in X- and Y-directions, respectively. In this study, four cases of boundary conditions were considered, and the corresponding buckling behavior were studied combined with plate aspect ratio. It was observed that the boundary condition of the case I resulted in the highest buckling resistance. Finally, a comparison was made between the buckling behavior of the uniaxially and biaxially loaded plate. It was revealed that the buckling resistance of a biaxially loaded plate is lower half than half of that of the uniaxially loaded plate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1398-1401
• /
• 2004

This paper proposes a new approach for the shape design of the rotating outer-ring type epicycloid plate gear by using instant velocity center. First, this method defines the instant velocity centers for rotating outer-ring type epicycloid plate gear and calculates the contact angles and the contact points by using the geometric relationships and the kinematic properties of the reducer. Second, it generates the full shape of the cycloidal plate gear. Finally, the paper develops CAD-program for construction of the design automation using the proposed method. This CAD-program is developed to have the functions of the friendly user interface and the simulation of the real operation for the cycloid reducer.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.28 no.4
• /
• pp.49-56
• /
• 1986

This study was carried out to investigate mechanical characteristics of the uniformly loaded skew-plate at 4 kinds of boundary condition : i) all edges are clamped (BC-1) , ii) all edges are simply supported (BC- 2), iii) two opposite edges are clamped and the other two edges are free (BC-3), and iv )two opposite edges are simply supported and the other two edges are free (BC-4). Various skew angles, 0$^{\circ}$, 10$^{\circ}$, 15$^{\circ}$, 30$^{\circ}$, 40: 45: and 60, of the plate were tested for the above boundary conditions. Resutts obtained from the study are summarized as follows ; 1.The lateral displacement at the center of a skew- plate was decreased as the skewangle increased at all of the boundary conditions. The decrements of the conditions of BC-3 and BC-4 were considerable. And, difference of the displacement between the boundary conditions was decreased as the skew-angle was increased. 2. X-moments (to the Y-axis) at the center of a skew- plate and the minimum principal moments were shown as a similar pattern of change with respect to the skew-angle variation between BC-i and BC-2 and between BC-3 and BC-4, and the pattern of change at the conditions of BC-3 and BC-4 were shown higher rates than those for the conditions of BC-i and BC-2 3.Y-moments (to the X- axis) at the center of a skew-plate and the maximum principal moment were decreased as the skew-angle increased in a similar pattern at all of the boundary conditions. 4.X-moments at the obtuse angle side of a skew-plate were shown as a parabolic pattern of change (frist increased after then decreased) as the skew-angle increased, and a skew-angle resulting the maximum absolute moment was depended on the boundary conditions. 5.Y-moments at the obtuse angle side of a skew-plate were affected by the skewangle much more at the boundary condtions of BC-2 and BC-4 than at the conditions of BC-i and BC-3. 6.Maximum principal moments at the obtuse angle side of a skew-plate at the skew angle of 40$^{\circ}$- 45$^{\circ}$ were resulted almost the same value at all of the boundary conditions .