• New & Renewable Energy
• /
• v.16 no.1
• /
• pp.47-57
• /
• 2020

In Floating PV (Photovoltaic) systems, PV modules are installed on water by utilizing the surface of idle water such as a reservoir and multipurpose dam. A floating PV system, therefore, has the advantage of efficiency in national land use and improved energy yield owing to cooling effect compared to on-land PV systems. Owing to the limitation of installation environment for a floating PV system, the system, however, has the disadvantage of an increase in transmission distance of DC (Direct current) cables. A longer transmission distance of a DC cable results in greater power loss due to a voltage drop. This leads to a decline in economic feasibility for the floating PV system. In this paper, the economic analysis for 10 floating PV systems installed in a reservoir has been conducted in terms of a change in annual power sales according to the variation of transmission losses depending on the factors affecting the voltage drop, such as transmission distance, cross-section area of underwater cable, the presence of joint box, and PV capacity.

• Tribology and Lubricants
• /
• v.34 no.5
• /
• pp.169-174
• /
• 2018

A multi-stage compressor (MSC) is comprised of several impellers installed in the pinion gear shaft driven by a main bull gear. In the pinion shaft, a thrust collar (TC) is installed to support the thrust load. The TC makes the lubrication system simpler in the MSC; therefore, it is widely used in similar kinds of machinery. Typically, TCs are installed on both sides of the bull gear and pressure is developed in the lubricated area by creating a taper angle on the TC and bull gear surface. In the current study, we developed a numerical analysis model to evaluate the performance of the TC considering its design parameters. We sloved the Reynolds equation using the finite element method and applied the half Sommerfeld condition to consider cavitation. Based on the pressure calculated in the lubricated area, we calculated the power loss and minimum film thickness. In addition, we calculated stiffness and damping using perturbation method. We performed parametric studies using the developed model. The results of the analysis show that the maximum pressure presents in the center area of the TC and it increases with the taper angle. The area over which pressure is developed decreases with the taper angle. The results also show that there is an optimum taper angle providing minimum power loss and maximum film thickness. Additionally, the stiffness and damping decrease with the taper angle. As the applied load increases, the power loss increases and the minimum film thickness decreases. However, the stiffness and damping increase with the applied load.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.7
• /
• pp.26-31
• /
• 2005

In this paper, a small BPF(band pass filter) is designed using new probe type for wireless communication system. The dielectric resonator is used high Q ceramics for low loss characteristic. In order to provide a band pass filter which can be reduced in dimension, can be reduced in height, and can be surface-mounted. The filter was fabricated using $TE_{01{\delta}}$ mode dielectric resonator. The input/output probes are attached to coner portion of the rectangular metal cavity. Results of the manufactured filter($12{\times}12{\times}8[mm]$) show that the center frequency is 9.95358[GHz], the insertion loss is -1.9[dB], the 3[dB]_bandwidth is 14.9[MHz], and the loaf Q is 664.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.6
• /
• pp.2489-2493
• /
• 2015

Background: Loss of heterozygosity (LOH) on chromosomal regions is crucial in tumor progression and this study aimed to identify genome-wide LOH in pancreatic cancer. Materials and Methods: Single-nucleotide polymorphism (SNP) profiling data GSE32682 of human pancreatic samples snap-frozen during surgery were downloaded from Gene Expression Omnibus database. Genotype console software was used to perform data processing. Candidate genes with LOH were screened based on the genotype calls, SNP loci of LOH and dbSNP database. Gene annotation was performed to identify the functions of candidate genes using NCBI (the National Center for Biotechnology Information) database, followed by Gene Ontology, INTERPRO, PFAM and SMART annotation and UCSC Genome Browser track to the unannotated genes using DAVID (the Database for Annotation, Visualization and Integration Discovery). Results: The candidate genes with LOH identified in this study were MCU, MICU1 and OIT3 on chromosome 10. MCU was found to encode a calcium transporter and MICU1 could encode an essential regulator of mitochondrial $Ca^{2+}$ uptake. OIT3 possibly correlated with calcium binding revealed by the annotation analyses and was regulated by a large number of transcription factors including STAT, SOX9, CREB, NF-kB, PPARG and p53. Conclusions: Global genomic analysis of SNPs identified MICU1, MCU and OIT3 with LOH on chromosome 10, implying involvement of these genes in progression of pancreatic cancer.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.20 no.2
• /
• pp.164-175
• /
• 2007

Purpose: The purpose of this study was to investigate the relationships between the herbal medicines used for women in puerperium on postpartum care, Kami-Saenghwatang(SHT) and Kami-Bohertang(BHT) and postpartum body composition change. We also examined the influence of gestational age, the number of parity and the route of delivery for gestational weight gain and postpartum weight loss. Methods: 239 women followed by postpartum care center. Variety factor s were conformed and then checked body composition analysis. 8 weeks later, we followed up body composition of 36 women among the former checked. and additionally asked the body weight of another 42 former checked women by telephone call. Results: $Mean{\pm}S.D$(standard deviation) of pre-pregnancy weight is $55.22{\pm}8.98kg$, $Mean{\pm}S.D$ of gestational maximun weight is $69.26{\pm}9.77kg$, $Mean{\pm}S.D$ of weight loss in postpartum 8 weeks(means sub-tract postpartum 1 week weight from postpartum 8 week weight) is $57.86{\pm}8.60kg$. The number of parities had corrrelation with gestational weight gain. Age, number of parities and route of delive were not significantly correlated with postpartum weight loss during 8 weeks after delivery, and also it was not correlated with body water mass, body fat mass, body mass index and body weight on postpartum 8 weeks whether they treated with SHT and BHT. conclusion: It was not correlated with body water mass, body fat mass, body mass index and body weight on 8 weeks postpartum whether they treated with SHT and BHT.

• Journal of the Korean Magnetics Society
• /
• v.14 no.5
• /
• pp.174-179
• /
• 2004

Attenuation of conduction noise through microstrip line attached with the high lossy iron flakes-rubber composites has been investigated in GHz frequencies. Microstrip line was designed with characteristic impedance of 50 $\Omega$ and a length corresponding to the center frequency of 3 GHz. Iron flakes were fabricated by mechanical forging of spherical iron powders using an attrition mill. The fabricated microstrip line shows a ideal propagation characteristics of S$\sub$11/ < -60 dB and S$\sub$21/ = 0 dB. Attaching a noise absorbing sheet on the microstrip line, S$\sub$11/ increases to about -10 dB and S$\sub$21/ decreases to -20～-60 dB depending on the length of absorbing sheet. The calculated power loss is as high as 80% in the frequency range 2～8 GHz. It is suggested that the most critical material parameter is magnetic loss for the enhancement of noise attenuation.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.6
• /
• pp.83-88
• /
• 2017

In this paper, a 3-port waveguide circulator of Ka-band millimeter-wave for isolation between transmit channel and receive channel at high power transmit mode is designed and fabricated for the seeker of the guided missile and circulator performance is verified through the S-parameter, high power and operation temperature test. At the configuration design, interface design between a seeker antenna and the circulator is considered and half-height of standard waveguide is applied for minimum and light weight body. The shape of permanent magnet and ferrite is optimized by simulation and tuning dielectrics at each port are placed for the best performance. In Fc(center frequency)${\pm}1000MHz$, designed waveguide circulator has below -20 dB return loss, below 0.5 dB insertion loss and below -23 dB isolation. It is found that circulator characteristics is similar to design results.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.2
• /
• pp.85-92
• /
• 2018

PURPOSE. This research evaluated clinical outcomes of two types of hydroxyapatite (HA)-coated implants: OT (Osstem TS III-HA, Osstem implant Co., Busan, Korea) and ZM (Zimmer TSV-HA, Zimmer dental, Carlsbad, USA). MATERIALS AND METHODS. The research was conducted on 303 implants (89 of OT, 214 of ZM), which were placed from January 16, 2010 to December 20, 2012. The prognosis was evaluated in terms of success rates, survival rates, annual marginal bone loss, and implant stability quotients (ISQ). The samples were classified into immediate, early, conventional, and delayed groups according to the loading time. RESULTS. Overall, there were no significant differences between OT and ZM in success rates, survival rates, and annual marginal bone loss, except for the result of secondary stability. OT showed $77.83{\pm}8.23ISQ$, which was marginally higher than $76.09{\pm}6.90ISQ$ of ZM (P<.05). In terms of healing periods, only immediate loading showed statistically significant differences (P<.05). Differences between OT and ZM were observed in terms of two indices, the annual marginal bone loss ($0.17{\pm}0.58mm/year$ < $0.45{\pm}0.80mm/year$) and secondary stability ($84.36{\pm}3.80ISQ$ > $82.48{\pm}3.69ISQ$) (P<.05). OT and ZM did not have any statistically significant differences in early, conventional, and delayed loading (P>.05). CONCLUSION. OT (97.75%) and ZM (98.50%) showed relatively good outcomes in terms of survival rates. In general, OT and ZM did not show statistically significant differences in most indices (P>.05), although OT performed marginally better than ZM in the immediate loading and 1-stage surgery (P<.05).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.843-854
• /
• 2013

This paper presents experimental research work for the evaluation of ultimate flexural behaviors of prestressed concrete beams with a corroded tendon. In order to evaluate the effects of loss of prestress or loss of tendon area on the ultimate flexural strength of prestressed concrete beams, static load tests are conducted using five prestressed concrete beams. After exposing prestressing tendons in two test beams using 25mm drill bit, the exposed tendons were corroded using an accelerating corrosion equipment to simulate loss of tendon area. During the tests, steel strains, concrete strains and displacements at the center of test beams were measured, and acoustic emission measurements were conducted to detect wire fractures. Based on the test results, evaluation method for predicting flexural strength of prestressed concrete beams with corroded tendons is investigated. In addition, evaluation methods for predicting the existence of corroded tendons in post-tensioned prestressed concrete beams at service loads are discussed.

• Journal of Advanced Navigation Technology
• /
• v.18 no.1
• /
• pp.29-34
• /
• 2014

Data fusion techniques combine data from multiple radars and related information to achieve more accurate estimations than could be achieved by a single, independent radar. In this paper, we analyze delay and loss of packets to be processed by multiple radar and minimize data processing interval from centralized data processing operation as fusing multiple radar data. Therefore, we model radar network about central data fusion, and analyze delay and loss of packets inside queues on assuming queues respectively as the M/M/1/K using NS-2. We confirmed average delay time, processing fused multiple radar data, through the analysis data. And then, this delay time can be used as a reference time for radar data latency in fusion center.