• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.69.1-69.1
• /
• 2005

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1326-1327
• /
• 2011

결정질 태양전지 제작 시 실리콘 기판 표면의 전극형성은 주로 스크린 프린트를 이용하여 형성되고 있다. 이는 squeeze 와 실리콘 기판과의 직접 접촉으로 인하여 기판의 파손이 야기 될 수 있으며, 보다 미세한 전극 형성이 어려운 단점이 있다. 본 연구에서는 비접촉식 잉크젯 프린팅을 이용한 태양전지의 전극형성에 관하여 기술하였으며, 고효율 태양전지를 제작하기 위해 레이저를 이용한 grooving 형성과 전극의 패턴에 따른 반사방지막층 제거를 통하여 Buried contact cell 제작을 연구하였다. 이를 통해 전극의 선 폭을 $45{\mu}m$로 구현하였으며, 나노 크기의 입자 형태를 띤 Ag 잉크를 이용하여 인쇄하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.5
• /
• pp.351-354
• /
• 2011

This paper was carried about thermal analysis for high efficiency point contact solar cell. Therefore, we carried about 2-D device and process simulator according to design and process parameters. As a result of simulations, power transfer efficiency have decreased more increasing temperature. Especially, power transfer efficiency of room temperature have been showed 25%. The other hand, power transfer efficiency of 350 K kalvin temperature have been showed 20%. Therefore, we will considered design with thermal dissipation of device.

• Electrical & Electronic Materials
• /
• v.10 no.10
• /
• pp.1034-1040
• /
• 1997

A solar cell conversion effiency was degraded by grain boundary effect in polycrystalline silicon. Grain boundaries acted as potential barriers as well as recombination centers for the photo-generated carriers. To reduce these effects of the grain boundaries we investigated various influencing factors such as emitter thickness thermal treatment preferential chemical etching of grain boundaries grid design contact metal and top metallization along boundaries. Pretreatment in $N_2$atmosphere and gettering by POCl$_3$and Al were performed to obtain multicrystalline silicon of the reduced defect density. Structural electrical and optical properties of slar cells were characterized before and after each fabrication process. Improved conversion efficiencies of solar cell were obtained by a combination of pretreatment above 90$0^{\circ}C$ emitter layer of 0.43${\mu}{\textrm}{m}$ Al diffusion in to grain boundaries on rear side fine grid finger top Yb metal and buried contact metallization along grain boundaries.

• Journal of Microbiology and Biotechnology
• /
• v.8 no.5
• /
• pp.478-483
• /
• 1998

For the enhanced production of a cardiac glycoside, digoxin, using in situ adsorption by biotransformation from digitoxin in plant cell suspension cultures, selection of proper resins was attempted and the culture conditions were optimized. Among various kinds of resins tested, Amberlite XAD-8 was found to be the best for digoxin production in considering adsorption characteristics as well as the effect on cell growth. Adequate time for resin addition was determined to be 36 h from the beginning of biotransformation and the presence of resins should be as short as possible to increase the productivity. In addition, to prevent the cells from direct contact with resin particles, immobilized systems were designed and examined. Immobilization further improved the advantages of in situ adsorption. It was confirmed that the increase of the contact area for mass transfer was an important factor in utilizing an immobilized system to enhance digoxin production.

• Journal of Hydrogen and New Energy
• /
• v.14 no.4
• /
• pp.291-297
• /
• 2003

As an alternative bipolar plate material for polymer electrolyte membrane fuel cell (PEMFC), TiN-coated 316 stainless was evaluated in terms of electrical contact resistance and water contact angle. Performance and lifetime of the TiN-coated 316 bipolar plates were measured in comparison with those of graphite and bare 316 bipolar plates. At a cell voltage of 0.6 V, current density of the single cells using graphite, AISI 316, and TiN/316 bipolar plates was 996, 796, and $896mA/cm^2$, respectively. By coating 316 stainless steel with TiN layer, performance degradation rate determined to be the voltage degradation rate at a cell voltage of 0.6 V was reduced from 2.3 to 0.43 mV/h.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.947-953
• /
• 2010

The KTX-Sancheon has been commercially operating on the high-speed line since March. 2. In order to verify the performance of high-speed train and core equipments such as current collection system, sophisticated tests and evaluating procedures should have been considering. In this paper, the load cell with a built-in strain-gauge which developed to improve measuring method of contact force between the pantograph and catenary system is introduced. The static test results of the load cell shows that its design is very suitable and applicable for the dynamic test and on-line test. After the test and evaluation of load cell's dynamic calibration with pantograph, we will be applied to test interaction characteristics between the pantograph and catenary system on the high-speed line.

• ETRI Journal
• /
• v.39 no.6
• /
• pp.859-865
• /
• 2017

This paper presents a method for determining the optimum active-area width (OAW) of solar cells in a module architecture. The current density-voltage curve of a reference cell with a narrow active-area width is used to reproduce the current density profile in the test cell whose active area width is to be optimized. We obtained self-consistent current density and electric potential profiles from iterative calculations of both properties, considering the distributed resistance of the contact layers. Further, we determined the OAW that yields the maximum efficiency by calculating efficiency as a function of the active-area width. The proposed method can be applied to the design of the active area of a dye-sensitized solar cell in Z-type series connection modules for indoor and building-integrated photovoltaic systems. Our calculations predicted that OAW increases as the sheet resistances of the contact layers and the intensity of light decrease.

• KSBB Journal
• /
• v.27 no.1
• /
• pp.45-50
• /
• 2012

In this paper, we investigated the effect of nanostructure on the cell behaviors such as adhesion and growth rate. Nanoporous structures with various diameters (30, 40, 45, 50, 60 nm) and 500 nm of the depth were fabricated using the anodizing method. The water contact angle of the surface consisting of nanopores with 30 nm diameter was 40 degree and those were 60~70 degree in cases of nanopores with over 40 nm diameter. Hela cells were cultivated on various nanoporous structure surface to investigate the cell behavior on nanostructure. As a result, Hela cells preferred 30 nm diameter nanoporous surface that has lower water contact angle. This result was confirmed by protein adsorption experiment and scanning electron microscope investigation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.81-84
• /
• 2006

To investigate the characteristics of water droplet on the gas diffusion layer from both upper-view and side-view of flow channel, a rig test apparatus was designed and fabricated with L-shape acryl plate in a $1mm{\times}1mm$ micro-channel. This experimental device is used to simulate the single droplet growth and its transport process under fuel cell operating condition. As a first step, we investigated the growth and transport of single water droplet with working temperature and air flow velocity. The contact angle and its hysteresis of water droplet at departing moment are measured and analyzed. It is expected that this study can provide the basic understanding of liquid water droplet behavior in gas flow channel and GDL interface during the PEM fuel cell operation.