• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 생명과학회지
• /
• 제12권6호
• /
• pp.700-707
• /
• 2002

높은 COD 농도의 유입수질에 따른 Bacillus 균주의 유기물 및 영양소 제거특성을 파악하고자 실험실 규모의 3가지 다른 기질 조성을 가지는 회분식 반응조(Rl, R2, R3)를 운전하였다. $NH_4^+$-N 및 $COD_{cr}$, 농도는 호기적 상태에서 95% 이상 제거되었으며, 각 반응조의 $NH_4^+$-N 및 $COD_{cr}$, 제거율은 각각 22.6 와 90.5%(Rl), 23.9 와 65.8%(R2), 30.2와 86.4%(R3)이었다. $NH_4^+$-N의 제거는 $NO_3^{-}$-N의 농도가 충분히 공급이 될 경우 제거효율이 높은 것으로 나타났고, 초기 nitrite의 농도가 높을 시에는 COD 처리효율을 크게 떨어뜨림을 알 수 있으며, 탈질에 이용되는 탄소량은 거의 없었다. 따라서, Bacillus 균주에 의한 탈질과정에서는 일반적 전자공여체 대신에 암모니아성 질소가 전자공여체로서 이용될 수 있다는 가능성을 보였다. $NO_3^{-}$-N농도는 무산소 조건에서 거의 탈질 되는 것으로 나타났으며, R3 반응조의 경우에만 호기상태에서도 10%의 제거가 일어났다. 총질소(TN)와 총인(TP)의 제거율은 각각 41.8 와 49.5%(Rl), 40.1와 35.8%(R2) 및 47.0 와 57.6%(R3) 이었다. Alkalinity는 호기조건에서 alkalinity의 농도가 많이 소모되었다가 다시 무산소 조건에서 탈질반응에 의하여 회복됨을 알 수 있었는데, 호기적 조건하에서 1 mg/L의 $NH_4^+$-N이 산화될 때 소모된 alkalinity는 Rl, R2, R3 반응조에서 각각 4.96, 5.41, 3.93 mg/L($CaCO_3$으로 환산한 농도로서)이었으며, 무산소 조건하에서는 1 mg/L의 $NO_3^{-}$-N이 제거되는 동안 회복되는 alkalinity는 각각 3.06, 3.17, 2.60 mg/L.($CaCO_3$으로 환산한 농도로서)이었다 Rl, R2, R3 각 반응조의 SOUR 값을 구해보면, 각각 38.5, 52.7 및 42.0 mg $O_2$/g MLSS/hr으로서 기존의 활성슬러지보다 높은 미생물 활성을 보였다. 각 반응조의 유기물질 용적부하율(OLR) 및 슬러지 생산량을 계산하면 각각 0.69 와 0.28(Rl), 0.77 와 0.20(R2) 및 0.61 kg COD/$m^3$/day 와 0.25 kg MLSS/kg COD(R3)이 었다. 유기물 부하율이 상당히 높은데 반해 슬러지 생산량은 다른 공법에 비해 다소 낮은 것으로 나타났다. 초기 $NO_3^{-}$-N 농도가 높은 R3 반응조는 무산소 조건하에서의 $NH_4^+$-N 1 mg 제거 당 가장 많은 양의 $NO_3^{-}$-N 제거 및 COD 1 mg 제거 당 가장 많은 $NO_3^{-}$-N 량이 제거되었다. Rl, R2 반응조에서의 $NH_4^+$-N 1 mg 당 제거된 COD mg수는 10.41-12.63으로서 호기적 탈질을 일으킨다고 보고된 T. pantotropha 균주를 사용한 실험결과와 비슷한 값을 나타내었고, $N_2$로의 변환에 의한 질소제거를 N-balance로부터 구해보면, R3 반응조의 경우가 가장 높은 제거율(40.9%)을 보였다. 이상의 결과들을 볼 때, Bncillus 균주는 호기적 탈질을 일으킬 수 있는 가능성이 있고, Bncillus 균주를 이용한 B3 공정은 탈질에 이용되는 탄소량이 거의 없고, 적은 alkalinity 소모에 의한 경제적 이익 등 장점을 가진 공정으로 보여 진다.

• Journal of Nutrition and Health
• /
• 제41권8호
• /
• pp.701-710
• /
• 2008

본 연구에서는 총항산화능 및 DPPH radicals 소거활성도를 통하여 항산화능을 확인한 산양삼 에탄올 추출물이 사염화탄소 투여로 급성 손상이 유도된 생쥐의 간에 대하여 보호 효능이 있는지를 확인하고자 하였다. 생리적 지표물질로 혈장 지질, GPT 활성, 혈장과 간의 TBARS 및 항산화효소 활성, 혈액 백혈구의 DNA fragmentation 등을 측정하여 다음과 같은 결과를 얻었다. 산양삼의 DPPH radicals 소거능은 76.85 ${\pm}$ 1.06%, IC50은 33.3 ${\mu}g$/mL였으며 총 항산화능은 2.13 ${\pm}$ 0.06 mmoL/mg으로 양성대조군으로 사용한 아스코르브산 (96.45 ${\pm}$ 0.07%, IC50 = 16.5 ${\mu}g$/mL, 3.63 ${\pm}$ 0.06 mmoL/mg)과 BHT (95.40 ${\pm}$ 0.71%, 3.12 ${\pm}$ 0.02 mmoL/mg) 보다는 낮았지만 천연물질로써는 높은 수준을 보였다. 장기 무게 및 식이 섭취량은 산양삼 추출물 투여 및 사염화탄소 처치 여부에 따라서 어떤 차이도 보이지 않았다. 혈장의 GPT와 혈중 트리글리세리드의 경우 정상대조군에 비해 사염화탄소단독투여군에서 유의하게 낮았으며, 산양삼 추출물 투여군에서는 큰 차이를 보이지 않았다. 혈청 총콜레스테롤 농도는 사염화탄소단독 투여군 (84.5 ${\pm}$ 23.0 mg/dL)이 정상 대조군 (140.6 ${\pm}$ 30.3 mg/dL)에 비하여 유의하게 감소하였으며, 산양삼 추출물 투여군 (130.68 ${\pm}$ 31.33 mg/dL)은 정상대조군과 같은 수준이었다 (p < 0.001). 사염화탄소 단독투여군의 간조직에서 TBARS는 정상대조군 (N)에 비해 28.64% 유의하게 증가하였으며 산양삼 추출물 투여군은 정상대조군과 비슷한 수치를 보였으나 (p < 0.001) 적혈구내의 TBARS는 세 군간의 유의한 차이가 없었다. 간조직의 SOD의 활성은 산양삼 추출물 투여군에서 유의하게 증가하였으며, 적혈구에서는 이러한 차이를 보이지 않았다. 그리고 적혈구내 GPx 활성은 사염화탄소 투여에 의해 20.1% 유의한 감소를 보였으며, 산양삼 추출액을 투여받은 군은 정상대조군의 수준을 유지하였다. 사염화탄소 투여군에서 혈장 백혈구의 tail DNA, tail length, tail moment 모든 값은 정상대조군에 비하여 각각 84.4%, 98.8%, 123.7% 증가하였으며, 산양삼 투여군에서는 이 모든 수치가 대조군의 수준으로 감소하였다 (p < 0.001). 이상의 결과를 종합해 보면 5일간 산양삼 에탄올 추출물을 미리 투여한 후 사염화탄소로 급성 간 손상을 유도하였을 때 혈 중 콜레스테롤 대사를 개선하고, 간의 지질 과산화를 효과적으로 억제하였으며 간의 SOD와 적혈구 GPx의 효소 활성을 대조군 이상으로 유지시키고, 산화적 손상으로부터 DNA를 보호하는 등의 일부 생리 활성을 확인하였다. 그러나 이런 산양삼의 항산화 활성의 작용 기전에 대하여 확실히 규명되어 있지 않아 추후보다 세부적인 연구가 필요할 것으로 사료된다.

• 생명과학회지
• /
• 제23권10호
• /
• pp.1230-1238
• /
• 2013

$17{\alpha}$-estradiol ($17{\alpha}-E_2$)의 에폽토시스 유도활성에 미치는 종양억제단백질 p53의 조절효과를 조사하고자, $17{\alpha}-E_2$에 의해 유도되는 에폽토시스 현상들을 인체 대장암 세포주 유래 클론인 HCT116 ($p53^{+/+}$) 및 HCT116 ($p53^{-/-}$) 세포에서 비교하였다. HCT116 ($p53^{+/+}$) 및 HCT116 ($p53^{-/-}$) 세포를 $17{\alpha}-E_2$ ($2.5{\sim}10{\mu}M$)로 처리하거나 혹은 HCT116 ($p53^{+/+}$) 및 HCT116 ($p53^{-/-}$) 세포를 $10{\mu}M$ $17{\alpha}-E_2$로 시간 별로 처리한 결과, HCT116 ($p53^{+/+}$)에 있어서는 세포독성과 에폽토시스-관련 sub-G1 peak의 비율은 처리농도와 시간에 의존적으로 나타났다. 그러나 HCT116 ($p53^{-/-}$) 세포의 경우는 이러한 현상이 미약하게 나타났다. $17{\alpha}-E_2$에 의해 유도되는 비정상적 유사분열방추사 형성, 중기판 염색체 배열의 미완성, 이에 따른 유사분열정지($G_2/M$ arrest) 등의 현상은 HCT116 ($p53^{+/+}$) 및 HCT116 ($p53^{-/-}$) 세포에서 유사한 수준으로 나타났다. 이에 반해, $17{\alpha}-E_2$에 의해 유도되는 Bak과 Bax의 활성화, 미토콘드리아의 막전위 상실(${\Delta}{\Psi}m$ loss), 그리고 PARP 분해 등의 현상은 HCT116 ($p53^{-/-}$) 세포에 비해 HCT116 ($p53^{+/+}$) 세포에서 훨씬 높은 수준으로 확인되었다. 아울러 $17{\alpha}-E_2$로 처리된 HCT116 ($p53^{+/+}$) 세포에서 확인되는 p53 (Ser-15)의 인산화 및 p53 수준의 증가와 일치하여, 세포 내의 p21및 Bax 수준도 현저히 증가하였다. 이때 $17{\alpha}-E_2$로 처리된 HCT116 ($p53^{-/-}$) 세포에서는 p21 및 Bax의 발현수준이 매우 낮았다. 한편, 에폽토시스 억제단백질인 Bcl-2 단백질 수준은 HCT116 ($p53^{-/-}$) 세포에 비해 HCT116 ($p53^{+/+}$) 세포에서 다소 낮았으나, 이러한 Bcl-2 단백질 수준은 $17{\alpha}-E_2$ 처리 후에도 크게 변화하지 않는 것으로 나타났다. 이러한 결과들은 $17{\alpha}-E_2$ 처리에 의해 유도되는 에폽토시스 유도 경로의 구성원들의 변화, 즉 비정상적 유사분열방추사 형성 및 이에 따른 유사분열정지($G_2/M$ arrest), 뒤이은 Bak 및 Bax의 활성화, 미토콘드리아의 막전위 상실, 그리고 이에 수반되는 caspase cascade 활성화 및 PARP 분해로 진행되는 에폽토시스 현상들 중에서, Bak 및 Bax의 활성화 단계가 종양억제단백질 p53의 에폽토시스 증진 활성에 의해 양성적으로 조절되는 작용 타켓임을 보여준다.

• Tuberculosis and Respiratory Diseases
• /
• 제43권6호
• /
• pp.945-953
• /
• 1996

연구배경: 진폐증을 비롯한 급만성 염증성 폐질환의 공통적인 병태생리는 활성화된 대식세포에서 분비되는 싸이토카인에 의해 염증세포 특히 독성 산화물질이나 단백분해효소 등을 분비하는 호중구의 침윤이 중요한 역할을 하며 염증이 지속되는 경우 비가역적인 섬유화를 가져오게 된다. 최근 강력한 호중구 화학주성인자로 밝혀진 IL-8은 TNF ${\alpha}$나 IL-1 에 의해 단핵세포나 대식세포, 섬유모세포등에서 분비되며 단백분해효소나 열 등에 안정하여 긴 반감기를 갖고 있어 다른 화학주성인자에 비해 지속적인 염증반응을 일으킨다. 실험 진폐증에서 유리규산에 폭로된 대식세포에서 TNF ${\alpha}$ 와 IL-1 이 증가함이 밝혀졌고, 유리규산과 같이 배양한 단핵세포에서 호중구 화학주성이 증가하며 lL-8 항체에 의해 호중구 화학주성이 억제됨이 보고된 바 있어 저자들은 IL-8 이 진폐증의 병태생리에서도 중요한 역할을 할 것으로 가정하게 되었다. 이에 진폐증 환자에서 IL-8의 분비가 증가하였는지 여부와 진폐증의 진행정도에 따른 IL-8 농도의 상관관계를 알아보고 진폐증의 조기진단에 IL-8을 생화학적 지표로 이용하고자 본 연구를 시도하였다. 방법: 분진 폭로력이 없는 아파트 경비원 16명을 대조군으로 하였고, 환자군은 흉부 X 선상 ILO 분류에 따라 의사진폐증군 16명, 소음영 진폐증군 16명, 대음영 진폐중군 16명을 대상으로 혈액 3$m{\ell}$를 채취하여 혈청을 얻은 다음 sandwich enzyme immnoassay technique 을 사용하여 IL-8을 정량분석하였다. 결과: 1. 대조군에 비하여 소음영 진폐증군과 대음영 진폐증군에서 연령이 높게 나타났으나 흡연력에는 차이가 없었으며 진폐증군사이에 분진 폭로력에도 유의한 차이는 없었다. 2. IL-8의 농도는 대조군에서 $17.85{\pm}33.85pg/m{\ell}$였던 것에 비하여 의사진폐증군에서 $70.50{\pm}53.63 pg/m{\ell}$ 소음영 진폐증군에서 $107.50{\pm}45.88pg/m{\ell}$ 대음영 진폐증군에서 $132.50{\pm}73.47pg/m{\ell}$로 대조군에 비하여 유의하게 증가하였다(p<0.001). 3. 진폐증군에서 진폐증이 진행할수록 IL-8 은 증가하는 경향을 보였고, 분산분석에서 다중비교를 하였을 때 의사진폐증군과 대음영 진폐증군사이에 통계적으로 유의한 차이가 있었다(p<0.05). 4. 진폐증 병형과 IL-8 농도사이에 상관계수는 0.4199(p<0.05)로 미약하지만 통계적으로 유의한 상관관계를 보여주었다. 결론: 진폐증의 조기진단을 위한 생화학적 지표로 IL-8 의 유용성이 클 것으로 기대되며 향후 진폐증에서의 IL-8항체의 호중구억제와 폐손상에 대한 방어 효과에 관한 연구가 이루어져야 할 것으로 생각된다.

• Tuberculosis and Respiratory Diseases
• /
• 제42권4호
• /
• pp.569-583
• /
• 1995

연구배경: 간질성 폐질환은 여러가지 다양한 원인에 의해, 또는 아직 밝혀지지 않은 원인에 의해 폐포염 및 폐간질내 염증으로 시작해 종국에는 폐섬유증으로 진행되는 질환들로 염증세포들의 이동에 필요한 접착분자들이 이들 질환의 발병기전에 중요한 역할을 할 것으로 추정되며, 현재까지는 뚜렷이 적당한 지표가 없었던 질환의 활동성을 판정하는 지표로 사용할 수 있을 가능성이 많다. 그러나 이제까지는 BAL내 AM에서 면역염색법으로 측정한 결과들로 방법 자체가 음성과 양성세포를 감별하기가 쉽지 않을 뿐 아니라 발현도 증가를 정량적으로 측정하지 못하는 단점이 있고, 따라서 발표된 결과들이 차이가 많다. 저자들은 간질성 폐질환 환자들에서 기관지 폐포세척액(BAL)내 AM과 임파구에서의 ${\beta}_2$-integrin(CD18)과 ICAM-1의 발현도를 FACS를 이용한 relative median fluorescence intenity(RMFI)를 측정하여 정상 대조군과 비교 관찰하고, 또한 혈청 및 BAL액내 가용정 ICAM-1(sICAM-1) 농도를 측정하고, BAL액내 다른 지표들과 비교하여 이들을 간질성 폐질환의 활성도를 반영할 수 있는 지표로 사용할 가능성을 알아 보았다. 방법: 대상은 조직학적으로 확인 된 미만성 간질성 폐섬유증(IPF) 환자 11명, 교원성 폐질환과 연관된 폐섬유증환자(CVD-PF) 6명, 폐유육종증 9명, 과민성 폐장염환자 2명과 대조군으후 건강한 정상인 9명이었고 BAL은 통상적인 방법을 사용하였다. ICAM-1 및 CD18은 단일항체를 사용하여 FACScan으로 median fluorescence intenity를 측정하여 RMFI를 구하고, sICAM-1농도는 ELISA법으로 측정하였다. 결과: AM에서 ICAM-1의 발현도는 $3.30{\pm}1.16$으로 대조군($0.93{\pm}0.18$)보다 증가되었고 임파구의 ICAM-1 발현도 $5.39{\pm}2.70$으로 대조군($1.06{\pm}0.21$)보다 높았다. CD18의 발현도는 임파구에서 $24.9{\pm}14.9$로 대조군($4.69{\pm}3.77$) 보다 향진되었으며, 이들 ICAM-1의 발현도는 AM 백분률과 역상관관계륜 보였고(r=-0.66, p=0.0001) 임파구의 백분율과는 정상관관계를 보였다(r=0.447, p=0.0116). 임파구가 증가되는 유육종증, 교원성질환, 과민성폐렴에서는 임파구의 ICAM-1 발현도와 BAL액내 임파구의 %(r=0.747, p=0.0006) 및 임파구농도(r=0.832, p=0.0002)와 좋은 상관관계를 보였고, 임파구의 IL-2수용체발현과도 연관관계를 나타내었다(r=0.539, p=0.0075). 또한 유육종증에서는 혈중 ACE 농도와 임파구의 ICAM-1 발현도가(r=0.905, p=0.0132) 높은 상관관계를 보여, 이들 접착분자 발현도가 병소의 활동성과 연관이 있음을 시사 하였다. 혈청내 sICAM-1농도는 환자군에서 $499.7{\pm}222.2\;ng/ml$로 대조군의 $199.0{\pm}38.9\;ng/ml$보다 높았으며(p=0.0097), BAL액내 sICAM-1농도도 환자군에서 $41.8{\pm}23.0\;ng/ml$로 대조군의 $20.1{\pm}13.6\;ng/ml$보다 증가를 보였다. 또한 혈청내 sICAM-1 농도는 AM의 ICAM-1 발현도 및 (r=0.554, p=0.0259) BAL액내 sICAM-1농도와 상관관계를 보였다. 또한 혈청 및 BAL액내의 albumin과 sICAM-1의 비율을 비교한 결과 BAL액내의 sICAM-1 농도가 훨씬 높은 것으로 미루어 대부분의 sICAM-1은 병소내에서 생성된 것임을 짐작할 수 있었다. 결론: 간질성폐질환환자들의 AM및 BAL-임파구에서 접착분자들의 발현도가 증가되었고, 혈청 및 BAL액내 sICAM-1 농도가 상승되어 있어 이들 접착분자들이 발병기전에 중요한 역할을 한다고 생각되며, 앞으로 이 활동성 판정의 지표로 사용할 기능성을 시사하였다.