• 수산해양기술연구
• /
• 제31권2호
• /
• pp.190-198
• /
• 1995

전원을 단락시킴이 없는 SCR이중 브리지 트리거 방식을 고안하여, 정역전이 가능한 SCR 서보증폭기로 구성하여 본 결과 다음과 같은 결론을 내릴 수 있었다. I. 출력전압의 부호를 변경시킬 때 현재의 전언부호가 반전될 때까지 도통 상태를 유지시키다가, 전원부호가 반전된 이후 적절한 SCR을 도통 시킴으로서 크리거 실패가 없게 되어, 전원을 단락시키지 않게 되고 SCR의 소손을 막을 수 있었다. II. -에서 약 30Hz 부근까지는 60Hz의 전원으로서 원하는 출력을 표현할 수 있었는데, 이는 대형 직류 전동기의 동특성을 충분히 확보할 수 있는 값이다. III. 유도성 부하의 경우라도 이미 도통된 SCR을 통하여 유동성부하L에 저장될 수 있는 에너지의 총량은 전원의 반주기 시간과 전원이 파고치값 한계내이므로, 다음 반주기동안 부호만 반전된 전원 전압과 동일한 반주기의 시간이 존재하므로, 에너지 보존의 법칙에 의해 반드시 다음 반주기 안에 현재도통된 SCR은 소호되게 되므로 트리거실패는 존재하지 않는다.

• Journal of Electrochemical Science and Technology
• /
• 제10권3호
• /
• pp.302-312
• /
• 2019

The voltage produced from the salinity gradient in reverse electrodialysis (RED) increases proportionally with the number of cell pairs of alternating cation and anion exchange membranes. Large-scale RED systems consisting of hundreds of cell pairs exhibit high voltage of more than 10 V, which is sufficient to utilize water electrolysis as the electrode reaction even though there is no specific strategy for minimizing the overpotential of water electrolysis. Moreover, hydrogen gas can be simultaneously obtained as surplus energy from the electrochemical reduction of water at the cathode if the RED system is equipped with proper venting and collecting facilities. Therefore, RED-driven water electrolysis system can be a promising solution not only for sustainable electric power but also for eco-friendly hydrogen production with high purity without $CO_2$ emission. The RED system in this study includes a high membrane voltage from more than 50 cells, neutral-pH water as the electrolyte, and an artificial NaCl solution as the feed water, which are more universal, economical, and eco-friendly conditions than previous studies on RED with hydrogen production. We measure the amount of hydrogen produced at maximum power of the RED system using a batch-type electrode chamber with a gas bag and evaluate the interrelation between the electric power and hydrogen energy with varied cell pairs. A hydrogen production rate of $1.1{\times}10^{-4}mol\;cm^{-2}h^{-1}$ is obtained, which is larger than previously reported values for RED system with simultaneous hydrogen production.

• 한국수소및신에너지학회논문집
• /
• 제31권1호
• /
• pp.132-137
• /
• 2020

Lithium secondary batteries have become an important power source for portable electronic devices such as cellular phones, laptop computers. Presently, commercialized lithium-ion batteries use a LiCoO₂ cathode. However, due to the high cost and environmental problems resulting from cobalt, an intensive search for new electrode materials is being actively conducted. Recently, solid solution LiMn_1-xNi_xO₂ have become attractive because of high capacity and enhanced safety at high voltages over 4.5 V. The Li_1.6Ni_0.35Mn_0.65O₂ compounds were conventionally prepared by a sol-gel method, which can produce the layered Li-Ni-Mn-O compounds with a high homogeneity. And by adding a graphene 2wt% the first charge-discharge voltage profiles was increased over Li_1.6Ni_0.35Mn_0.65O₂ compound. Also, the variation s of the discharge capacities with cycling showed a higher capacity retention rater. In this study, material lifecycle evaluation was performed to analyze the environmental impact characteristics of Li_1.6Ni_0.35Mn_0.65O₂ & graphene 2wt% half-cell manufacturing process. The software of material life cycle assessment was Gabi. Through this, environmental impact assessment was performed for each process. The environmental loads induced by Li_1.6Ni_0.35Mn_0.65O₂ & graphene 2wt% synthesis process were quantified and analyzed, and the results showed that the amount of power had the greatest impact on the environment.

• 청정기술
• /
• 제27권2호
• /
• pp.152-159
• /
• 2021

다양한 환경문제를 일으키는 휘발성 유기 화합물(volatile organic compounds, VOCs)은 산업 지대 및 도심의 실내외에서 다양하게 발생한다. 악취성 VOCs는 심미적 불쾌함과 더불어 인체에 심각한 영향을 미칠 수도 있다. 기존에 악취성 VOCs를 저감하는 방식에 비하여, 전기 분해를 통해 생산된 산화제를 이용한 수세정 방식은 오염 물질 저감과 동시에 산화제의 재생이 가능하다는 장점이 있다. 본 연구에서는 염소계 산화제인 OCl^-을 생산하기 위한 최적 조건을 연구하였다. 산화 및 환원 전극의 종류와 전해질의 종류, 전해질의 농도 및 전류 밀도를 변화시켰다. 산화 전극은 Ti/IrO₂, 환원 전극은 Ti을 사용하였을 때 OCl^- 생산이 가장 우수하고 안정적이었다. 전해질의 OCl^- 생산 능력은 KCl과 NaCl이 유사하게 나타났으나, 경제적이고 쉽게 구할 수 있는 NaCl이 최적이라고 판단하였다. OCl^- 생산 속도가 우수하고 농도가 가장 높게 생산된 NaCl 농도 및 전류 밀도 조건은 0.75 M NaCl, 0.03 A cm^-2이었다. 하지만 전력 비용을 고려했을 때 본 실험에서는 1.00 M NaCl, 0.01 A cm^-2의 조건의 OCl^- 생산이 가장 효율적이었다. 실제 현장 적용시 오염물질의 농도 및 특성에 따라서 전류밀도를 조절하여 OCl^-을 생산하는 것이 바람직할 것이다.

• Bulletin of the Korean Chemical Society
• /
• 제31권7호
• /
• pp.2025-2030
• /
• 2010

When $Cu^{2+}$ was used as an electron acceptor, removal of $Cu^{2+}$ was achieved from the synthesized wastewater (SW) in the cathode compartment of a microbial fuel cell (MFC). By addition of $KNO_3$, the different initial pH of the SW showed no effect on the removal efficiency of $Cu^{2+}$. For $Cu^{2+}$ concentration of 50 mg/L the removal efficiencies were found to be 99.82%, 99.95%, 99.58%, and 99.97% for the $KNO_3$ concentrations of 0, 50, 100 and 200 mM, and to be 99.4%, 99.9%, 99.7%, and 99.7% for pH values of 2, 3, 4, and 5, respectively. More than 99% $Cu^{2+}$ was removed for the $Cu^{2+}$ concentrations of 10, 50, and 100 mg/L, while only 60.1% of $Cu^{2+}$ was removed for the initial concentration of 200 mg/L (pH 3). The maximum power density was affected by both $KNO_3$ concentration and initial concentration of $Cu^{2+}$. It was increased by a factor of 1.5 (from 96.2 to 143.6 mW/$m^2$) when the $KNO_3$ concentration was increased from 0 to 200 mM (50 mg/L $Cu^{2+}$), and by a factor of 2.7 (from 118 to 319 mW/$m^2$) when $Cu^{2+}$ concentration was increased from 10 to 200 mg/L (pH 3).

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권2호
• /
• pp.179-184
• /
• 2016

In recent years, the on-resistance, power loss and cell density of Si power devices have not exhibited significant improvements, and performance is approaching the material limits. GaN is considered an attractive material for future high-power applications because of the wide band-gap, large breakdown field, high electron mobility, high switching speed and low on-resistance. Here we report on the Ohmic contact resistance and reverse-bias characteristics of AlGaN/GaN Schottky barrier diodes with and without annealing. Annealing in oxygen at $500^{\circ}C$ resulted in an increase in the breakdown voltage from 641 to 1,172 V for devices with an anode-cathode separation of $20{\mu}m$. However, these annealing conditions also resulted in an increase in the contact resistance of $0.183{\Omega}-mm$, which is attributed to oxidation of the metal contacts. Auger electron spectroscopy revealed diffusion of oxygen and Au into the AlGaN and GaN layers following annealing. The improved reverse-bias characteristics following annealing in oxygen are attributed to passivation of dangling bonds and plasma damage due to interactions between oxygen and GaN/AlGaN. Thermal annealing is therefore useful during the fabrication of high-voltage GaN devices, but the effects on the Ohmic contact resistance should be considered.

• 전기화학회지
• /
• 제4권4호
• /
• pp.160-165
• /
• 2001

황산원자를 포함하는 mercapto화합물은 도금시 전착속도를 증가시키는 첨가제로 알려져 있는데, 이 중 4가지의 mercapto 화합물을 선정하여 농도를 변화시켜가며 Hull cell test, Haring-Blum cell test, cathodic polarization, EQCM(Electrochemical Quartz Crystal Microbalance)등을 이용하여 도금특성 및 throwing power를 알아보았다. Cathode polarization 및 EQCM을 통한 구리 전착량을 알아본 결과 4가지의 mercapto 화합물 중 3-mercapto-1-propanesulfonic acid가 activator로서 가장 적당하였으며, 그 농도가 20 ppm에서 throwing power를 증가시키고, 농도 및 활성 과전압이 오직 $Cl^-$만 포함되었을 때보다 cathodic scan시 100 mV 만큼 shift되어 증착속도를 증가시킴을 알 수 있었다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제41권5호
• /
• pp.457-462
• /
• 2018

The purpose of this study was to compare image quality of indirect digital radiography (IDR) system using the International Electro-technical Commission standard (IEC 62220-1), and to suggest the analysis of noise power spectrum (NPS) which were applied to IEC 62220-1 in medical imaging. In this study, Pixium 4600 (Trixell, France) which is indirect flat panel detector (FPD) was used. The size of image receptor (IR) is $7{\times}17$ inch (matrix $3001{\times}3001$) which performed 14bit processing and pixel pitch is $143{\mu}m$. In IEC standard, NPS evaluation were applied to RQA3, RQA5, RQA7 and RQA9. Because of different radiation quality, each region of interesting (ROI) were compared. The results of NPS indicated up to $3.5mm^{-1}$ including low Nyquist frequency. RQA5 indicated the lowest NPS and the others indicated higher NPS results relatively. NPS result of ROI a38 was higher than ROI a92 and this result indicated that there are more noise in left (cathode) than right (anode). This study were to evaluate NPS by using different radiation quality and setting the each ROI, and to suggest the quantitative methods of measuring NPS.

• 전기전자학회논문지
• /
• 제18권1호
• /
• pp.25-30
• /
• 2014

본 논문에서는 파워 클램프에 적용하기 위한 SCR 기반의 ESD 보호회로를 제안하였다. 기존 SCR 구조의 낮은 홀딩 전압에 의한 래치-업 문제를 개선하기 위해 n+ 플로팅 영역을 삽입하고 추가적인 n-웰과 p-웰까지 확장된 p+ 캐소드 영역을 통해 높은 홀딩 전압을 가질 수 있도록 고안되었다. 제안된 ESD 보호회로는 높은 홀딩 전압을 통해 정상 동작 상태에서의 래치-업 면역 특성을 확보하였으며, 우수한 ESD 보호 능력을 가진다. 제안된 ESD 보호회로는 Synopsys사의 TCAD 시뮬레이션을 통해 전기적 특성을 검증하였다. 시뮬레이션 결과, 트리거 전압은 약 27.3 V에서 최대 32.71 V 사이에서 변화하는 반면, 홀딩 전압은 4.61 V에서 최대 8.75 V까지 상승하는 것을 확인하였다. 따라서 제안된 ESD 보호회로는 트리거 전압은 기존 SCR과 비슷한 수준을 유지하면서 높은 홀딩 전압을 갖는다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.981-983
• /
• 1999

In this paper, the electrical characteristics of $\lambda$ vibration-mode piezoelectric transformer for applying to CCFL driving inverter was investigated. Piezoelectric transformer was made of PZT - PMN - 0.5wt% $Nb_{2}O_{5}$ composition. As a results of the electrical characteristics of piezoelectric transformer, when applied voltage was $35[V_{rms}]$ in $100[k{\Omega}]$ load resistance, output voltage was about $710[V_{rms}]$ and output power was more than 2[W]. As output power increased, step-up ratio and temperature was very stable until output power was 2.5[W]. Also, Efficiency was maximum in $70[k{\Omega}]$ load resistance, and about 89[%]. Also, when CCFL was used as load, the maintaining voltage was $700[V_{rms}]$ and the luminescence was $2000[cd/m^2]$ in applying $25[V_{rms}]$ to piezoelectric transformer. Conclusively, piezoelectric transformer fabricated in this paper can be applied to piezoelectric inverter for CCFL driving.