• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2006년도 학술발표회 논문집
• /
• pp.472-477
• /
• 2006

This study aims at investigating the failure cases of the pre-cast block system in river environments which widely used nowadays and reviewing the effect and flow resistance for grass concrete structure through the physical experiments by hydraulic model test and developing application method in river slope or levee which has rigid flood resistance. Grass concrete structure has been independently tested under high velocity flow under the super critical condition, it survived the 8 m/sec maximum flow velocity. This results shows grass concrete system is also suited to use in aggressive river environments such as repairing a flood damaged embankment that had placed at risk the adjacent drainage channel with vegetation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.57-60
• /
• 1998

Poly(3-hexylthiophene)(P3HT) was synthesized by use of FeCl$_3$ as a oxidizing agent at $25^{\circ}C$. The infrared spectrum of our polymer gave good evidence for the conjugation of 3-hexylthiophene monomer unit. P3HT contains the HT(head-to-tail) linkage larger than 64% based on NMR analysis. Electronic absorption and photoluminescence studies show that cast films of P3HT have three exciting state. Absorption spectrum was separated with three maximum peaks by Giese-French method and shifted to the shorter wavelength with increasing temperature. Separated absorption spectrum of P3HT is well adapted to PL peak appeared at longer wavelength. Low temperature PL spectrum is well separated at 669nm, 733nm and 812nm.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.998-1002
• /
• 1997

This study has been performed to predict beam absorption with analysis of temperature field by using a FEM in co /sab 2/ laser hardening and to invesrigate into some effects of power density and travel speed of laser beam on the microstructure and hardness of ductile cast iron treated by laser surface hardening technique. Optical micrograph has shown that large martensite and small amount of retained austenite appear in inside hardened zone. Hardness measurement has revealed that the range of maximum hardness value is Hv=415 .+-. 10. The power density increases and the travel speed decreases, the depth of hardened zone increases due to increase of input power density.

• 대한심미치과학회지
• /
• 제10권2호
• /
• pp.21-30
• /
• 2001

Fiber reinforced materials have favorable mechanical properties. Moreover, the strength to weight ratios of this material is superior to those of most alloys. Comparing to the metals, it showed many other advantages as well, including non-corrosiveness, translucency and easy repair characteristic. Since, it has the potential for the chair-side and laboratory fabrication, it is not surprising that fiber reinforced composites offer the potential for use in various applications in dentistry. To make the well-fitted restorations, Fiber reinforced composite (FRC) has been suggested as an alternative framework material for the implant supported fixed prosthesis. Two fixed partial denture fabrication procedures were tried. Vectris fiber was pressed to the EsthetiCone gold cylinder on the implant positioned cast. And then, Targis were added on it. In the other method, we used the customized component using UCLA abutment. The beads for retaining the Vectris fiber were added on the abutment. If careful laboratory and clinical techniques were done, these two techniques would fulfill the demands of the esthetics and strength.

• 대한기계학회논문집A
• /
• 제28권4호
• /
• pp.410-418
• /
• 2004

The multiaxial fatigue test under in-phase and out-of$.$phase load were performed to study what degradation phenomenon affects fatigue life with virgin and 3600 hrs degraded materials. The various kind of fatigue data fur fatigue life prediction were acquired under pure axial and pure torsional load of fully reversal condition. The models which was investigated are: 1) the von Mises equivalent strain range, 2) the critical shear plane approach method of Fatemi-Socie(FS) parameter, 3) the modified Smith-Watson-Topper(SWT) parameter. The result showed that, fatigue life by material degradation are decreased and life prediction which was used the FS parameter is not conservative but the best result.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2010년도 정기 학술대회
• /
• pp.517-520
• /
• 2010

BIM 설계시 의무사항으로 포함되어 있는 원지형과 암층별 지층, 흙막이 공법 중 CIP(Cast in Place Pile)공법, 구조물 형상을 3차원 정보 모델로 생성하고, 모델을 통해 정확한 2D 도면의 생성, 각 공정간의 간섭검토, 암층별 토공량 및 흙막이의 수량을 산출하였다. 최종 설계안을 도출하기 위해 3차원 기법이 설계 초기에 도입되어 반복적인 노력과 시간을 최소화하여 많은 설계대안을 제시하도록 하였으며, 정확한 설계결과를 얻기 위해, 2D 설계와 3D 설계를 병행 수행함과 동시에 이 과정과 결과를 비교하여 3차원 모델의 효과를 검증하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.188-191
• /
• 2005

Lower arm for automobile has been made in steel traditionally. Nowadays steel is being substituted fur aluminum to reduce weight of automobile. Widely applied production method of aluminum component has been casting processes or cast/forging processes. But casting or cast/forging processes have limits of application to parts which is required high strength durability like automotive component. In this research, hot forging process has been adopted to produce aluminum lower arm to ensure required mechanical properties. To reduce production cost, 2 pieces with 1 blow process was developed. Optimization and verification of hot forging process for aluminum lower arm was performed by computer aided engineering using finite volume methods.

• 대한치과기공학회지
• /
• 제44권1호
• /
• pp.24-30
• /
• 2022

This research introduces the manufacturing process of the metal-framework of one of the maxillary partial dentures, the "obturator", using milling wax-blocks, for patients with palate loss due to oral cancer. It explains the protocol of taking the patient's oral impression, preparation of a working cast, scanning, designing using a computer-aided design program, investing the milling wax-blocks, and completing the obturator. This method does not follow the traditional wax and agar process thereby reducing the errors arising during the manufacturing process and decreasing the time, material, and labor required. Moreover, the retention, stability, and compatibility of the metal framework were observed to be high in both the working cast and oral cavity.

• 콘크리트학회논문집
• /
• 제23권3호
• /
• pp.281-287
• /
• 2011

최근 프리캐스트 하부 구조에 대한 연구가 많이 이루어지고 있으며 국내 및 국외에서 현장 적용이 이루어지고 있는 실정이다. 그러나 프리캐스트 하부 구조의 경우 대부분 교각의 기둥 부분에 대한 연구에 매진하고 있으나, 프리캐스트 하부 구조를 완성하려면 코핑부 또한 사전 제작 및 현장 운반이 필요한데, 이를 위해서는 코핑부의 경량화를 이루어야 한다. 이렇듯 코핑부의 경량화를 위해서 코핑부 역시 기둥부와 같이 분절화하여 현장에서 조립하는 공법을 적용하여야 교량의 하부 구조 시스템이 완전하게 프리캐스트 하부 구조가 될 수 있을 것이다. 이 연구에서는 사전에 제안된 프리캐스트 교각에 맞는 프리캐스트 코핑부를 기존 연구자에 의하여 제시되어진 모델을 기반으로 한 수정 모델을 제안하였으며, 이를 해석 및 실험 연구를 통하여 거동 분석을 수행하여 그 성능을 분석하였다.

• 한국주조공학회지
• /
• 제33권1호
• /
• pp.32-40
• /
• 2013