• 한국연소학회:학술대회논문집
• /
• 2002.06a
• /
• pp.185-191
• /
• 2002

The influence of N2 addition on soot formation, flame temperature and NOx emissions is investigated experimentally with methane fuel co-flow diffusion flames. The motivation of the present investigation is the differences in NOx reduction reported between fuel-side and oxidizer-side introduction of N2. To determine the influence of dilution alone, fuel was diluted with nitrogen while keeping the adiabatic flame temperature fixed by changing the temperature of the reactants. And to see the thermal effect only, air was supplied at different temperature without N2 addition. N2 addition into fuel side suppressed the soot formation than the case of oxidizer-side, while flame temperature enhanced the soot formation almost linearly. These results reveals the relative influences of the thermal, concentration effects of N2 additives on soot formation In accordance with experimental study, numerical simulation using CHEMKIN code was carried out to compare the temperature results with those acquired by CARS measurement, and we could find that there is good agreement between those results. Emission test revealed that NOx emissions were affected by not only flame temperature but also N2 addition.

• Korean Journal of Food Science and Technology
• /
• v.22 no.6
• /
• pp.640-645
• /
• 1990

Changes of the electrophoretic patterns of myofibrillar proteins by sugar audition and heat treatment was studied. In the electrophoretic patterns of myofibrills prepared from no sugar added meat, as the intensity of higher molecular weight band such as myosin heavy chain showed a remarkable decrease by heating, that of lower molecular weight band such as actin showed no change. That from sugar added meat showed more remarkable decrease in the intensity of higher molecular weight band than that from no sugar added meat and this tendency was most noticeable in case of glucose addition. The effect of digestion with proteases after sugar addition and heat treatment on the electrophoretic patterns exhibited the descending order of trypsin >chymotrypsin >peptidase. By digestion with these three enzymes at one time myosin produced 27.000 dalton and 32.000 dalton components, and actin showed 16,000 dalton component. in the case of heat treatment, a part of actin was not digested. And in the case of glucose addition the myosin aggregates was not digested with these three enzymes at a time.

• Korean Journal of Food Science and Technology
• /
• v.17 no.3
• /
• pp.146-154
• /
• 1985

Low-salted Kochuzang was made by the replacement of a part of NaCl with 4% ethanol as the preservative. Comparative analysis were performed for general components in 7 kinds of low-salted Kochuzang. The activities of ${\alpha}-and{\beta}-amylase$ and protease were high in ripened Kochuzang of low salt concentration in case of addition of alcohol. The changes of total sugar and pH were remarkably decreased when alcohol and salt were added. Total acid contents showed a remarkable increase when alcohol was not added, and in case of salt concentration. Total nitrogen contents were not remarkably changed, but the contents of amino nitrogen and ammonia nitrogen were increased in case of low salt conuntration with alcohol. Reducing sugar contents were increased in case of low salt concentration and alcohol added. Alcohol contents were not remarkably changed in case of addition of alcohol, but when alcohol was not added and low salt concentration they showed a remarkable increase(about 2.2%). A good Kochuzang may be produced by adding 4% alcohol to a low salted one (5.1% content in Kochuzang) in seventy days of the fermentation.

• Journal of Information Technology Applications and Management
• /
• v.17 no.3
• /
• pp.1-24
• /
• 2010

Most of enterprises depend on a data modeler during developing their management information systems. In formulating business requirements for information systems, they widely and naturally use the interview method between a data modeler and a field worker. But, the discrepancy between both parties would certainly cause information loss and distortion that lead to let the systems not faithful to real business works. To improve or avoid modeler-dependant data modeling process, many automated data design CASE tools have been introduced. However, since most of traditional CASE tools just support drawing works for conceptual data design, a data modeler could not generate an ERD faithful to real business works and a user could not use them without any knowledge on database. Although some CASE tools supported conceptual data design, they still required too much preliminary database knowledge for a user. Against these traditional CASE tools, we proposed a Requirement-Oriented Entity Relationship Model for automated data design tool, called ROERM. Based on Non-Stop Methodology, ROERM adopts inner systematic modules for complete and sound ERD that is faithful to real field works, where modules are composed of interaction modules with a user, rules of schema operations and sentence translations. In addition to structure design of ROERM, we also devise detailed algorithms and perform an experiment for a case study.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.3
• /
• pp.252-258
• /
• 2017

This paper describes on introduction of CASE 3 for EFD-CFD comparison workshop which is incharged of aerodynamic subcommittee of The Korean Societry or Aeronautical and Space Science. In addition, the results of candidate for CASE 3 were compared with experimental result and computational result. Currently, for this case 3, there are eight candidates from company, university and research institute. According to comparison of their results, they are in accordance with experimental data and computational data.

• Journal of Veterinary Clinics
• /
• v.22 no.4
• /
• pp.435-438
• /
• 2005

Two dogs (case 1:2-year-old intact male German Shepherd-mixed dog and case 2: 4-year-old intact female Jindo miked) with perineal hernia were referred to the Chonbuk Animal Medical Center, Chonbuk National University. In the both cases, there were unilateral perineal swelling involving the right side of the anus. In addition, in case 2, swelling was also present ventral to the anus. Rectal palpation of pelvic diaphragm revealed weakness of the muscles. Both cases were surgically treated using muscle transposition technique for hemiorrhaphy. In case 1, transposition of the superficial gluteal and internal obturator muscles and in case 2, transposition oi semitendinosus muscle was performed for hemiorrhaphy and reconstruction of the pelvic diaphragm. Both dogs became recovered after the surgical correction and no complications were observed during 10-month (casel) and 9-month(case2). Muscle transposition can be a useful technique for the treatment of perineal hernia in the dog.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.1
• /
• pp.25-30
• /
• 2021

The differential gear system is a device designed to distribute the driving force of both vehicle wheels and control the rotational speed when the vehicle turns on a curve. The differential device consists of a differential gear case, a ring gear, and a pressure ring. A differential pinion gear and side gear are mounted on the differential pinion shaft inside the differential gear case. In this study, a pin press-fitting device that mounts the pinier gear and side gear to the differential pinion shaft in the differential gear case was designed, and a jig device for pin press-fitting using servo press was developed. In addition, by precisely measuring the pin press-in load and press-in distance according to the pin hole diameter of the differential gear shaft, the optimization of the pin pressin process was established.

• Journal of Environmental Science International
• /
• v.30 no.7
• /
• pp.519-527
• /
• 2021

Moving average precipitation provides periodic precipitation patterns by solving precipitation irregularities. However, due to uncertain moving average periods, excessive data smoothing occurs, which limit the possibility to analyze groundwater levels in the short term. Nonetheless, groundwater level fluctuation can compensate these limitations as it can calculate appropriately for unit time and verify the effect of precipitation penetrated into groundwater in a short time period. In this study, the characteristics of groundwater level were evaluated using groundwater level fluctuation to compensate for limitations of groundwater level analysis using moving average precipitation. In addition, the groundwater quality was investigated using the electrical conductivity fluctuation. The study site was Hyogyo-ri, Yesan-si, Chungcheongnam-do. Four observation wells and an automated weather system were used. The correlation between groundwater level fluctuation and precipitation (Case 1) and the correlation between groundwater level and moving average precipitation (Case 3) were compared. In the analysis for 1 hour data, the correlation coefficient of Case 1 was higher than that of Case 3, and in the analysis for 1 day data, the correlation coefficient of Case 3 was higher than that of Case 1.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.82-88
• /
• 1999

In this study, the formation of mullite phase with mineralizer have been investiagated Hadong Kaolin and boehmite were used as starting materials and also of TiCl4 and MnCl4 aquous solution were used as a mineralizer. In the addition of 3.5% MnO as a mineralizer, mullite single phase could be obtained at 125$0^{\circ}C$ without any other second phases. However in the addition of TiO2 as a mineralizer, mullite single phase is obtained at above 135$0^{\circ}C$. Therefore the formation of mullite is lowered in the case of MnO as a mineralizer than of TiO2. Because it is easy to obtain mullite single phase in the case of MnO addition, all the characteristics improved. The values of bulk density, water absorption and bending strength at room temperature were 2.72g/㎤, 0.27% and 180 MPa, respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.1053-1055
• /
• 2002

Recently CRT is getting large-sized, Flatness and High Fine Pitched in the meantime the raw material for shadow mask is in rapid progress of thinness, Low Thermal Expansion and high strength.Until now we have used AK(Aluminum Killed) & Invar(Fe-Ni alloy) materials for main raw material of shadow mask component. However recently Nb and Co addition and Nb+Co addition, which has advantage of Low Thermal Expansion and High Strength. has been developed as well as applying in mass production as CRT's trend has become more flat and fine pitch. Among of them, Co addition has been mass production as forming type (Flat CRT) with the beneficial effect of low thermal expansion & high strength for the first time. Since then Nb+Co addition has been used in mass production by the request of much higher strength of shadow mask component. In case of Nb addition, It's thermal expansion coefficient is a little lower than normal Invar and a little higher than Co addition, meanwhile Its Mechanical property is almost similar to Co Addition. The used samples of this experiment are 36%Ni + Fe, 32%Ni + 5%Co + Fe, 32%Ni + 5%Co + 0.3%Nb + Fe, 32%Ni + 0.3%Nb + Fe with heat treatment temperature of 600$^{\circ}C$, 650$^{\circ}C$, 700$^{\circ}C$, 750$^{\circ}C$, 800$^{\circ}C$, 850$^{\circ}C$, 900$^{\circ}C$ respectively under the condition of 15min holding time. After heat treatment, we have observed the change of mechanical property with addition of small elements through mechanical property investigation and metal structure observation as well as transition of thermal expansion coefficient by measuring of thermal expansion coefficient at 850$^{\circ}C$. In conclusion, 5%Co addition indicates that its thermal expansion coefficient is very similar under the condition of at 850$^{\circ}C$ for 15min 's heat treatment. From the experimental result it is suggested that Co addition is mostly suitable for Doming property and Nb addition is mostly suitable for Drop property.