• Journal of the Korean institute of surface engineering
• /
• v.55 no.6
• /
• pp.441-447
• /
• 2022

Silicon-based materials are one of the most promising anode active materials in lithium-ion battery. A carbon layer decorated on the surface of silicon particles efficiently suppresses the large volume expansion of silicon and improves electrical conductivity. Carbon coating through chemical vapor deposition (CVD) is one of the most effective strategies to synthesize carbon- coated silicon materials suitable for mass production. Herein, we synthesized carbon coated SiOx via pilot scale CVD reactor (P-SiO_x@C) and carbon coated SiO_x via industrial scale CVD reactor (I-SiO_x@C) to identify physical characteristic changes according to the CVD capacity. Reduced size silicon domains and local non-uniform carbon coating layer were detected in I-SiO_x@C due to non-uniform temperature distribution in the industrial scale CVD reactor with large capacity, resulting in increased surface area due to severe electrolyte consumption.

• Analytical Science and Technology
• /
• v.19 no.6
• /
• pp.460-467
• /
• 2006

Carbon-coated $TiO_2$ was prepared by $CCl_4$ solvent mixing method with different heat treatment temperature (HTT). Since the carbon layers derived from pitch on the $TiO_2$ particles were porous, the carbon-coated $TiO_2$ sample series showed a good adsorptivity and photo decomposition activity. The BET surface area was decreased by the increasing of the heat treatment temperature. The SEM results present to the characterization of surface texture on the carbon-coated $TiO_2$ sample and carbon distributions on the surfaces for all the materials used. The main elements of C, O and Ti were shown from EDX spectra. And the quantity of these elements is very rich in the samples. From XRD data, the pristine anatase peaks were observed in the X-ray diffraction patterns for the carbon-coated $TiO_2$ at the different HTTs. However, the rutile peaks were observed for the carbon-coated $TiO_2$ at HTT of 1073 K and 1123 K. Finally, the excellent photocatalytic activity of carbon-coated $TiO_2$ with UV-vis spectra between absorbance and time could be attributed to the homogeneous coated carbon on the external surface and structural phase transform, and the photocatalytic activity was decreased by the increasing of the HTT.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.4
• /
• pp.743-748
• /
• 2010

Boron nitride (BN) and carbon nitride (CN) films, which have relatively low work functions and commonly exhibit negative electron affinity behaviors, were coated on carbon nanotubes (CNTs) by magnetron sputtering. The CNTs were directly grown on metal-tip (tungsten, approximately 500nm in diameter at the summit part) substrates by inductively coupled plasma-chemical vapor deposition (ICP-CVD). The variations in the morphology and microstructure of CNTs due to coating of the BN and CN films were analyzed by field-emission scanning electron microscopy (FE-SEM). The energy dispersive x-ray (EDX) spectroscopy and Raman spectroscopy were used to identify the existence of the coated layers (CN and BN) on CNTs. The electron-emission properties of the BN-coated and CN-coated CNT-emitters were characterized using a high-vacuum field emission measurement system, in terms of their maximum emission currents ($I_{max}$) at 1kV and turn-on voltage ($V_{on}$) for approaching $1{\mu}A$. The results showed that the $I_{max}$ current was significantly increased and the $V_{on}$ voltage were remarkably reduced by the coating of CN or BN films. The measured values of $I_{max}-V_{on}$ were as follows; $176{\mu}A$-500V for the 5nm CN-coated emitter and $289{\mu}A$-540V for the 2nm BN-coated emitter, respectively, while the $I_{max}-V_{on}$ of the as-grown (i.e., uncoated) emitter was $134{\mu}A$-620V. In addition, the CNT emitters coated with thin CN or BN films also showed much better long-term (up to 25h) stability behaviors in electron emission, as compared with the conventional CNT emitter.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.10
• /
• pp.1480-1488
• /
• 2003

Synthesis of carbon nanomaterials on a substrate coated with metal nitrates using an ethylene fueled inverse diffusion flame was illustrated. The effects of radial distance, residence time of the substrate, and hydrocarbon composition on the synthesis of carbon nanomaterials were investigated. The effects of catalyst metal particles were also studied using SUS304 substrates coated with Fe(NO$_3$)$_3$ (ferric nitrate, nonahydrate) and Ni(NO$_3$)$_2$(nickel nitrate, hexahydrate), and Cu substrate. Carbon nanomaterials, with diameters ranging from 30 - 70 nm, were observed on the substrate for both cases of using substrates only and using them with metal nitrates. In case of using the substrate with metal nitrates, the formation and growth of carbon nanomaterials were occurred in the lower temperature region than that of using the substrates only due to the easy activation of the metal particles coated on the surface of the substrates.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.4
• /
• pp.168-171
• /
• 2005

The electrochemical properties of $LiFePO_4$ as a cathode for Li-ion batteries were improved by incorporating conductive carbon into the $LiFePO_4$. X-ray diffraction analysis and SEM observations revealed that the carbon-coated $LiFePO_4$ consisted of fine single crystalline particles, which were smaller than the bare $LiFePO_4$. The electrochemical performance of the carbon-coated $LiFePO_4$ was tested under various conditions. The carbon-coated $LiFePO_4$ showed much better performance in terms of the discharge capacity and cycling stability than the bare $LiFePO_4$. The improved electrochemical performances were found to be attributed to the reduced particle size and enhanced electrical conductivity of the $LiFePO_4$ by the carbon.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.7
• /
• pp.1607-1610
• /
• 2009

The carbon-coated Si/Cu powder has been prepared by mechanical ball milling and hydrocarbon gas decomposition methods. The phase of Si/Cu powder was analyzed using X-ray diffraction (XRD), dispersive Raman spectroscopy, electron probe microanalysis (EPMA) and transmission electron microscope (TEM). The carbon-coated Si/Cu powders were used as anode active material for lithium-ion batteries. Their electrochemical properties were investigated by charge/discharge test using commercial LiCo$O_2$ cathode and lithium foil electrode, respectively. The surface phase of Si/Cu powders consisted of carbon phase like the carbon nanotubes (CNTs) with a spacing layer of 0.35 nm. The carbon-coated Si/Cu/graphite composite anode exhibited a higher capacity than commercial graphite anode. However, the cyclic efficiency and the capacity retention of the composite anode were lower compared with graphite anode as cycling proceeds. This effect may be attributed to some mass limitations in LiCo$O_2$ cathode materials during the cycling.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1590-1592
• /
• 2007

In this study, we prepared CNF (carbon nanofiber) by the solvothermal method for FED (field emission display) applications. We controlled several conditions to synthesize effective CNF for field emission applications. Nano-sizesd Pt nanoparticles were coated on the CNF. In this study, we have applied Pt nanoparticles- coated CNF which can be produced in mass, to field emission application.

• Journal of Korean Port Research
• /
• v.14 no.3
• /
• pp.373-378
• /
• 2000

Oil spill in sea water is the most frequent and significant problem of marine pollution. As an early detection sensor of the pollution, an activated carbon coated quartz crystal is prepared and examined for its performance of detection sensitivity and stability. Powdered activated carbon and phenol resin is coated on the surface of the sensor and the sensor is baked for an hour. Adsorption of acetone dissolved in water and salt water is measured using frequency shift of quartz crystal at different concentrations of solute material. The outcome indicates that the sensor preparation is adequate and the measurement of solute concentration is stable and sensitive enough to be implemented on the monitoring of solute concentration is stable and sensitive enough to be implemented in the monitoring of organic pollution of sea water.

• Journal of Electrochemical Science and Technology
• /
• v.9 no.1
• /
• pp.1-8
• /
• 2018

The effect of mixing ratio on the corrosion protection of carbon steel coated by a film composed of poly(vinylidene) fluoride (PVDF) and poly(methyl methacrylate) (PMMA) was examined using electrochemical impedance spectroscopy. Surface crystallization behavior and thermal properties of the PVDF/PMMA coated carbon steel were evaluated using polarized optical microscopy and differential scanning calorimetry, respectively. A Maltese cross-pattern spherulite crystal was observed in the PVDF/PMMA coating film, which became more apparent with increasing PVDF content. The highest corrosion protection performance was achieved with 60 wt.% PVDF-coated carbon steel, and delamination and corrosion reactions were observed for 20 wt.% PVDF-coated carbon steel. Further, corrosion protection performance with an amorphous/crystal mixture (PVDF/PMMA, 60/40 (w/w)) was better than those observed in the amorphous domain and the perfect-crystal domain of the PVDF/PMMA blended coating system.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.2
• /
• pp.122-128
• /
• 2002

This study was conducted to synthesize the diamond like carbon films by plasma enhanced chemical vapor deposition (PECVD). The effects of gas composition on growth and mechanical properties of the films were investigated. A little amount of hydrogen or oxygen were added to base gas mixture of methane and argon. Methane dissociation and diamond like carbon nucleation were enhanced by installing negatively bias grid near substrate. The deposited films were indentified as hard diamond like carbon films by micro-Raman spectroscopy. The surface and fractured cross section of the films which were observed by scanning electron microscopy showed that film growth is very slow as about 0.3$\mu\textrm{m}$/hour, and relatively uniform with hydrogen addition. Vickers hardness of tungsten carbide (WC) cutting tool increased from about 1000 to 1600~1800 by deposition of DLC film, that of commercial TiN coated tool was about 1270. In cutting test of aluminum 6061 alloy, DLC coated cutting tool showed 1/3 or lower crater and flank wear than TiN coated or non-coated WC cutting tools.