• Journal of the Korean Vacuum Society
• /
• v.21 no.2
• /
• pp.106-112
• /
• 2012

New equipment for quantitative and qualitative adsorption of volatile organic compound was set up, and using this equipment, adsorption behaviors of various carbob-based nanomaterials and $TiO_2$ thin films prepared by atomic layer deposition were compared. We could conclud that $TiO_2$ thin films can show higher adsorption capacity of toluene comparing to the carbon-based nanostructures due to higher affinity of the surface OH groups of $TiO_2$ towards toluene adsorption. We also demonstrate that our method allows to discriminate reversible and irreversible adsorptions at a given temperature.

• Carbon letters
• /
• v.10 no.1
• /
• pp.14-18
• /
• 2009

We measured the degree of macrodispersion of the various single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs) using UV-VIS-NIR absorption spectroscopy. CNTs were dispersed with SDS of 2 wt % in deionized water using the homogenizer and then were further centrifugated at 6000 g for 10 min. The degree of macrodispersion, expressed by $D_m({\lambda})=A_a({\lambda})/A_b({\lambda})^*100$ (%), where ${\lambda}$ is the wavelength and $A_a({\lambda})$ and $A_b({\lambda})$ are the absorbance of the sample after and before centrifugation, respectively. In the case of MWCNTs, we evaluated the degree of macrodispersion by the average degree of macrodispersion ($D_m({\lambda})$) between 1000 and 1200 nm. The degree of macrodispersion of SWCNTs was evaluated at the wavelength in which van Hove singularity-related transition regions were excluded, i.e., the range was chosen between ${E_{11}}^S$ and ${E_{22}}^S$ peaks. We have estimated six samples with the same method. The standard deviation of each sample was lower than 5. Therefore, we presented a reliable evaluation method for the macrodispersion of CNTs for standardization.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.421-421
• /
• 2009

Since carbon nanotubes (CNTs) are discovered, tremendous attentions have been paid to these materials due to their unique mechanical, electrical and chemical properties. Thereupon, many methods to produce a large scale of CNTs have been contrived by many scientists and engineers. Thus the examination of growth mechanisms of CNTs, which is essential to produce CNTs in large scale, has been an attractive issue. Though many scientists have been strived to investigate and understand the growth mechanisms of CNTs, many of them still remain controversial or unclear. Here we introduce representative growth mechanisms of CNTs, based on broadly employed fabrication methods of CNTs. We applied Thermo-electrical Pulse Induced Evaporation (TPIE) method based on field and thermal evaporation to synthesis of CNTs. However TPIE method was originally devised to fabricate graphene sheets and $Ge_2Sb_2Te_5$ nanostructures. While performing TPIE experiments to synthesize graphene, we eventually found experimental results widely supporting the growth model of CNTs proposed already. We observed the procedure of growth of CNTs obtained by TPIE method through Transmission Electron Microscopy (TEM). We believe this study provides an experimental basis on understanding and investigating carbon-based nanomaterials.

• Carbon letters
• /
• v.16 no.2
• /
• pp.132-134
• /
• 2015

When manufacturing bulk graphite, pores develop within the bulk during the carbonization process due to the volatile components of the fillers and the binders. As a result, the physical properties of bulk graphite are inferior to the theoretical values. Impregnants are impregnated into the pores generated in the carbonization process through pressurization and/or depressurization. The physical properties of bulk graphite that has undergone impregnation and re-carbonization processes are outstanding. In the present study, a green body was manufactured by molding with natural graphite flakes and phenolic resin at 45 MPa. Bulk graphite was manufactured by carbonizing the green body at 700 and it was subsequently impregnated with impregnants having viscosity of 25.0 cP, 10.3 cP, and 5.1 cP, and the samples were re-carbonized at $700^{\circ}C$. The above process was repeated three times. The open porosity of bulk graphite after the final process was 22.25%, 19.86%, and 18.58% in the cases of using the impregnant with viscosity of 25.0 cP, 10.3 cP, and 5.1 cP, respectively.

• Membrane Journal
• /
• v.26 no.5
• /
• pp.351-364
• /
• 2016

In recent decades, many researchers have tried to improve desalination performances of polyamide (PA) thin-film composite membranes (TFCs) by incorporating nanomaterials into a selective PA layer. This review focuses on PA-based nanocomposite membranes with high performances for energy-effective desalination in reverse osmosis. Carbon based nanomaterial (e.g., graphene oxide (GO), carbon nanotubes (CNT)) and/or other nanoparticles (e.g., zeolite, silica and etc.,) were applied to overcome the trade-off correlation between water permeability and salt rejection of current polymeric desalination membranes. Here, this brief review will discuss current studies of PA-based nanocomposite membranes with enhanced separation characteristics and provide the future research direction to achieve further improved desalination performances.

• Carbon letters
• /
• v.18
• /
• pp.30-36
• /
• 2016

Well-dispersed Ag₃VO₄ nanoparticles @polyacrylonitrile (PAN) nanofibers were synthesized by an easily controlled, template-free method as a photo-catalyst for the degradation of methylene blue. Their structural, optical, and photocatalytic properties have been studied by X-ray diffraction, transmission electron microscopy, field-emission scanning electron microscopy equipped with rapid energy dispersive analysis of X-ray, photoluminescence, and ultraviolet-visible spectroscopy. The characterization procedures revealed that the obtained material is PAN nanofibers decorated by Ag₃VO₄ nanoparticles. Photocatalytic degradation of methylene blue investigated in an aqueous solution under irradiation showed 99% degradation of the dye within 75 min. Finally, the antibacterial performance of Ag₃VO₄ nanoparticles @PAN composite nanofibers was experimentally verified by the destruction of Escherichia coli. These results suggest that the developed inexpensive and functional nanomaterials can serve as a non-precious catalyst for environmental applications.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.2
• /
• pp.108-113
• /
• 2017

We investigated the effect of graphite electrode geometry and combination on nanocarbon material synthesis using underwater discharge plasma(UDP). The UDP system consists of two graphite electrodes and beaker filled with de-ionized water. A high voltage of 15 kV with a frequency of 25 kHz is applied to produce UDP using an alternating-current power source. The UDP system with conical electrodes produced the largest amount of products due to the concentration of electrical fields between electrodes. In addition, hollow-shaped stationary electrode and conical-shaped moving electrode stores discharge-induced bubbles and maintains longer reaction time. We found from Raman spectroscopy and electron microscopy that high quality carbon nanomaterials including carbon nanotubes are synthesized by the UDP system.

• Safety and Health at Work
• /
• v.12 no.3
• /
• pp.403-415
• /
• 2021

Background: This study aimed to assess the possibility of benzene exposure in workers of a Korean semiconductor manufacturing company by reviewing the issued patents. Methods: A systematic patent search was conducted with the Google "Advanced Patent Search" engine using the keywords "semiconductor" and "benzene" combined with all of the words accessed on January 24, 2016. Results: As a result of the search, we reviewed 75 patent documents filed by a Korean semiconductor manufacturing company from 1994 to 2010. From 22 patents, we found that benzene could have been used as one of the carbon sources in chemical vapor deposition for capacitor; as diamond-like carbon for solar cell, graphene formation, or etching for transition metal thin film; and as a solvent for dielectric film, silicon oxide layer, nanomaterials, photoresist, rise for immersion lithography, electrophotography, and quantum dot ink. Conclusion: Considering the date of patent filing, it is possible that workers in the chemical vapor deposition, immersion lithography, and graphene formation processes could be exposed to benzene from 1996 to 2010.

• Applied Microscopy
• /
• v.48 no.4
• /
• pp.117-121
• /
• 2018

The multiple length scale analysis of previously designed Fe-Mn-Al-C based low-density model alloys reveals the difference in ordered ${\kappa}-carbide$, $(Fe,Mn)_3AlC_x$, between Fe-25Mn-16Al-5.2C (at%) alloy and Fe-3Mn-10Al-1.2C (at%) alloy. For the former alloy composition consisting of fully austenite grains, ${\kappa}-carbide$ showed majorly cuboidal and minorly pancake morphology and its chemical composition was not changed through aging for 24 h and 168 h at $600^{\circ}C$. Meanwhile, for the isothermally annealed ferritic alloy system for 1 hr at 500 and $600^{\circ}C$, the dramatic change in the chemical composition of needle-shape ${\kappa}-carbide$, $(Fe,Mn)_3(Fe,Al)C_x$, was found. Here we address that the compositional fluctuations in the vicinity of the carbides are significantly controlled by abutting phase, either austenite or ferrite. Namely, the cooperative ordering of carbon and Al is an important factor contributing to carbide formation in the high-Mn and high-Al alloyed austenitic steel, while the carbon and Mn for the low-Mn and high Al alloyed ferritic steel.

• Advances in nano research
• /
• v.16 no.4
• /
• pp.353-363
• /
• 2024

The incorporation of nanoplatelets in composite and polymeric materials represents a recent and innovative approach, holding substantial promise for diverse property enhancements. This study focuses on the application of nanocomposites in the production of sports equipment, particularly soccer balls, aiming to bridge the gap between theoretical advancements and practical implications. Addressing the longstanding challenge of suboptimal interaction between carbon nanofillers and epoxy resin in epoxy composites, this research pioneers inventive solutions. Furthermore, the investigation extends into unexplored territory, examining the integration of glass fiber/epoxy composites with nanoparticles. The incorporation of nanomaterials, specifically expanded graphite and graphene, at a concentration of 25.0% by weight in both the epoxy structure and the composite with glass fibers demonstrates a marked increase in impact resistance compared to their nanomaterial-free counterparts. The research transcends laboratory experiments to explore the practical applications of nanocomposites in the design and production of sports equipment, with a particular emphasis on soccer balls. Analytical techniques such as infrared spectroscopy and scanning electron microscopy are employed to scrutinize the surface chemical structure and morphology of the epoxy nanocomposites. Additionally, an in-depth examination of the thermal, mechanical, viscoelastic, and conductive properties of these materials is conducted. Noteworthy findings include the efficacy of surface modification of carbon nanotubes in preventing accumulation and enhancing their distribution within the epoxy matrix. This optimization results in improved interfacial interactions, heightened thermal stability, superior mechanical properties, and enhanced electrical conductivity in the nanocomposite.