• Journal of Electrochemical Science and Technology
• /
• v.6 no.4
• /
• pp.139-145
• /
• 2015

Capacitive deionization (CDI) process is a novel approach for desalination of an aqueous salt solution. In the present study, an activated carbon cloth (ACC) is proposed as effective electrode material. Initially the carbon cloth was activated in 1 M and 8 M HNO₃ for 9 hours at room temperature. The untreated and chemically activated carbon cloth (ACC) electrode materials were subjected to BET surface area measurements in order to get information about their specific surface area, average pore size, total pore volume and micropore area. The above materials were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM) also. The electrochemical studies for the electrodes were done using cyclic voltammetry (CV) in 0.1 M Na₂SO₄ medium. From the studies, it was found that resistivity of the activated carbon cloth electrodes (treated in 1 M and 8 M HNO₃) was decreased significantly by the chemical oxidation in nitric acid at room temperature and its capacitance was found to be 90 F/g (1 M HNO₃) and 154 F/g (8 M HNO₃) respectively in 0.1 M Na₂SO₄ solution. The capacitive deionization behavior of a single cell CDI with activated carbon cloth electrodes was also studied and reported in this work.

• ETRI Journal
• /
• v.36 no.3
• /
• pp.361-366
• /
• 2014

In this paper, a new, simple capacitive tilt sensor with a metallic ball is proposed. The proposed tilt sensor has only two electrodes and a metallic ball, and this design assists in managing the inherent contact problem in measuring tilt angles. Capacitive sensing, compared with other types of tilt sensor, has many advantages such as simplicity, noncontact measurement, long-throw linear displacement, and sub-micron plate spacing. Its design and fabrication process are significantly simpler than previous types of tilt sensors. The dimensions of the prototype tilt sensor are $20mm{\times}20mm$, and the diameter of the polystyrene tube is 5 mm with a tube thickness of 0.15 mm. An analytical study of the prototype capacitive tilt sensor was undertaken, and the experimental results demonstrate the relationship between the tilt angles and measured capacitances compared with the analytical study.

• Membrane Journal
• /
• v.29 no.5
• /
• pp.292-298
• /
• 2019

The purpose of this study was to improve the desalination performance by using split electrodes in the capacitive desalination process. The experiment was carried out by measuring the desalination efficiency of the NaCl aqueous solution according to the partitioning of the electrode at 20 mL/min flow rate, 1.2 V, 3 min adsorption conditions, and -1 V, 1 min desorption conditions. The desalination efficiency for the non-divided electrodes with a surface area of $146cm^2$ reached 40% while the divided electrode with a surface area of $133cm^2$ showed a desalination efficiency of 57%. The desalination efficiency of the same split electrode was 49% at 2 cm divided interval and 57% at 1cm divided interval. The desalination efficiency of the split electrode was higher than that of the normal CDI and narrower divided intervals increased the performance.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.1
• /
• pp.57-64
• /
• 2014

Carbon electrodes for capacitive deionization were fabricated through mixing two different carbon powders (activated carbon powder, carbon black) with different particle sizes to investigate physical or electrochemical properties and finally desalination performances of the electrodes with various compositions of two carbon powders in weight and were compared with the electrode consisting of activated carbon. As a result, the electrode structure became more packed as increasing the amount of carbon black and resulted in 10% increase in mesopore fraction. The specific capacitance obtained from cyclic voltammograms of various electrodes showed that the electrode containing carbon black only had 107.4 F/g, while the specific capacitance of the electrode having more amount of carbon black increased and was higher than the one having no carbon black. The results of desalination runs in a capacitive deionization cell exhibited that the electrode having the highest amount of carbon black (1 wt%) in this study had the highest desalting efficiency, and no significant pH variation was observed during the runs. It was analyzed using accumulated charge that the fraction of non-Faraday current increased as the amount of carbon black increased in the electrodes. It can be concluded that the addition of carbon black changed the electrode structure resulting in an increase in the fraction of mesopore and finally enhanced the desalting efficiency by decreasing Faraday current.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.1
• /
• pp.38-43
• /
• 2004

Porous carbon aerogel-silica gel composite materials were used as the electrodes of capacitive deionization(CDI) process, which were prepared by a paste rolling method. The electrochemical parameters such at current values, coulombs af a function of cycle, and CDI efficiencies were investigated for 10th and 100th cycles in 1,000ppm NaCl solution. Carbon aerogel-silica gel composite electrodes showed good wet-ability and higher mechanical strengths even under the NaCl solutions as well. In our experimented runs, all of the composite electrodes also are showed good cycle-ability without destroy of active material during cycles and decreased manufacturing times by $50\%$. Conclusively, the adding of silica gel powder to carbon aerogel leads to the effective performance of CDI process due to effective utilization of active materials by increasing the wet-ability and mechanical hardness.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.129-133
• /
• 2016

Theoretical and graphical analysis of pull-in-voltage and figure of merit for a fixed-fixed capacitive Micro Electromechanical Systems (MEMS) switch is presented in this paper. MEMS switch consists of a thin electrode called bridge suspended over a central line and both ends of the bridge are fixed at the ground planes of a coplanar waveguide (CPW) structure. A thin layer of dielectric material is deposited between the bridge and centre conductor to avoid stiction and provide low impedance path between the electrodes. When an actuation voltage is applied between the electrodes, the metal bridge acquires pull in effect as it crosses one third of distance between them. In this study, we describe behavior of pull-in voltage and figure of merit (or capacitance ratio) of capacitive MEMS switch for five different dielectric materials. The effects of dielectric thicknesses are also considered to calculate the values of pull-in-voltage and capacitance ratio. This work shows that a reduced pull-in-voltage with increase in capacitance ratio can be achieved by using dielectric material of high dielectric constant above the central line of CPW.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.12
• /
• pp.2590-2597
• /
• 2002

A new torque measuring apparatus adopting the basic principle of a capacitive type sensor is proposed in this article. Two plate electrodes are working as a capacitive sensor, whose capacitance varies as torque is applied. One end of each plate is connected to the torque carrying shaft. Output characteristics of the torque sensor were theoretically analyzed and its validity was investigated through experiment. Calculations and calibration experiments show that the output is nonlinear, that is, the sensitivity is very high at low torque but decreases as torque increases. The sensitivity of the proposed system is about 100 times roughly higher than that of a conventional 4-strain gauge type torque sensor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.557-560
• /
• 1999

The design of large area thin film transistor liquid crystal displays (TFT-LCDs) requires consideration of cross-talks between the data lines and pixel electrodes. These limits are imposed by the parasitic capacitive elements present in a pixel. The capacitive coupling of the data line signal onto the pixel causes a pixel voltage error. In this study semi-empirical capacitance model which is adopted from VLSI interconnection capacitance calculations was used to calculate mutual coupling capacitances. With calculated mutual coupling capacitances and given image pattern, the root mean square(RMS) voltage of pixel is calculated to see vertical cross-talk from the first to the last column. The information obtained from this study could be utilized to design the larger area and finer image quality panel.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1896-1898
• /
• 2001

An offset problem caused by the static parasitic capacitors is analyzed and then some techniques to reduce their effect on the capacitive position sensor are presented. Also new offset compensation technique is proposed that by adjusting the magnitudes of the modulating signals independently, the charge imbalance between electrodes caused by the parasitic capacitors is eliminated without sensor gain variation. Simulation results are given to validate the proposed compensation technique.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.44.2-44
• /
• 2003