• 대한전자공학회논문지SD
• /
• 제45권11호
• /
• pp.95-101
• /
• 2008

최근 발진수정자에 칩패키지를 결선한 SMD형의 적층세라믹 발진기를 많이 사용한다. 이러한 발진기들은 그 길이 및 패키지 내부의 패턴 등에 의하여 부유인덕턴스 및 기생 커패시턴스가 발생하고, 전원의 반사 및 잡음 발생으로 출력신호의 진폭감소 및 신호 손실이 발생하여 발진기 성능을 정상적으로 평가할 수 없다. 본 논문에서는 발진기와 계측기의 부정합임피던스로 부터 발생한 신호 손실 및 진폭감소를 방지하기 위해 지그 회로를 개발한다. 이를 통하여 발진기의 정확한 스펙트럼 분석 및 성능을 평가함으로써 발진기의 성능향상을 기한다.

• 한국공작기계학회논문집
• /
• 제11권2호
• /
• pp.17-23
• /
• 2002

A cylindrical capacitance-type spindle displacement sensor was developed and its effectiveness as a system to monitor cutting forces during hard turning was tested in this research. The sensor was installed between the face of spindle cover and the chucking element and measured pure radial motion of the spindle under the condition with presence of roundness error at measured surface. To prove the effectiveness of the developed system hard aiming tests using ceramic inserts and tool steel as workpiece were conducted. The workpiece was hardened up to 65 Rc. The variations of pure radial motion of the spindle ware measured during the cutting tests. The signals from the sensor showed the same pattern of cutting force variations from the tool dynamometer due to the progress of tool wear. As the flank wear of the ceramic tool increased both static component of cutting forces and the amount of center shift of spindle orbit increased, Results from the research showed that the developed sensor could be utilized as an effective and cheap on-line sensing device to monitor cutting conditions and tool performance in the un-manned machining center.

• Bulletin of the Korean Chemical Society
• /
• 제23권5호
• /
• pp.741-744
• /
• 2002

Single phase of multicomponent oxide ZrTiO4 film could be prepared through surface sol-gel route simply by coating the mixture of 100 mM zirconium butoxide and titanium butoxide on $Pt/Ti/SiO_2Si(100)$ substrate, following pyro lysis at $450^{\circ}C$, and annealing it at 770 $^{\circ}C.$ The dielectric constant of the film was reduced as the film thickness decreased due to of the interfacial effects caused by layer/electrode and a few voids inside the multilayer. However, the dielectric property was independent of applied dc bias sweeps voltage (-2 to +2 V).The dielectric constant of bulk film, 31.9, estimated using series-connected capacitor model was independent of film thickness and frequency in the measurement range, but theoretical interfacial thickness, ti, was dependent on the frequency. It reached a saturated ti value, $6.9{\AA}$, at high frequency by extraction of some capacitance component formed at low frequency range. The dielectric constant of bulk ZrTiO4 pellet-shaped material was 33.7 and very stable with frequency promising as good applicable devices.

• Corrosion Science and Technology
• /
• 제2권1호
• /
• pp.7-11
• /
• 2003

Photoelectrochemical response and electrochemical impedance behavior was investigated for passive film formed on sputter-deposited Cr alloy in $0.1kmol{\cdot}m^{-3}$. Photoelectrochemical action spectrum could be separated into two components, which were considered to be derived from $Cr_2O_3$ ($E_g\sim3.6eV$) and $ Cr(OH)_3 $ ($E_g\sim2.5eV$). The band gap energy, $E_g$, of each component was almost constant for various applied potentials. polarization periods and alloying additives. The photoelectrochemical response showed negative photo current for most potentials in the passive region. Therefore, the photo current apparently exhibited p-typesemiconductor behavior. On the other hand, Mort-Schottky plot of the capacitance showed positive slope, which means that passive film formed on Cr alloy has n-type semiconductor property. These apparently conflicting results are rationally explained assuming that the passive film on Cr alloy formed in the acid solution has n-type semiconductor property with a fairly deep donor level in the band gap and forms an accumulation layer in the most of potential region in the passive state.

• 전자공학회논문지SC
• /
• 제43권4호
• /
• pp.45-52
• /
• 2006

본 연구에서는 위상잡음과 지터(jitter) 특성을 개선한 $5mm{\times}7mm$ 크기의 적층 세라믹 SMD(surface mounted device)형 VCXO를 개발한다. PECL(positive emitter coupled logic) 칩패키지를 발진수정자에 결선한 VCXO는 그 길이 및 패키지 내부의 패턴 등에 의하여 부유인덕턴스 및 기생 커패시턴스가 발생하고, 전원의 반사 및 잡음 발생으로 출력신호의 진폭 감소 및 신호 손실이 발생하여 발진기 성능을 정상적으로 평가할 수 없다. 이러한 신호 손실 및 진폭감소를 방지하기 위해 지그(Jig) 시스템을 개발하고, 이를 통하여 발진기의 정확한 스펙트럼 분석 및 성능을 평가한다. 동작전원은 3.3 V, 주파수 범위 120-180 MHz 및 Q인수는 5K이다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.197-200
• /
• 2005

As Plasma Immersion ion Implantation (PIII) using a conducting grid is very useful to reduce the effect of capacitance and charging in surface modification. If the bias voltage applied to the conducting grid is in the range of hundreds of volts, the effects of surface charge and space charge substantially affect the incident ion energy and ion current to the surface. In this paper, through an 1d and a 2d PIC simulation the time varying formation of the space charge and surface charge is analyzed. Experiment with the optimally designed grid on the basis of the simulation results is conducted, and the results of both cases with grid and without grid are compared. In our work with Poly Urethane(PU), the improvement of adhesion is yielded by increasing surface roughness and decreasing Si component of PU.

• 전기학회논문지P
• /
• 제61권1호
• /
• pp.41-46
• /
• 2012

Electrolytic power capacitors have been widely used in power conversion system such as inverter or UPS because of characteristics of large capacitance, high-voltage and low-cost. The electrolytic capacitor, which is most of the time affected by the aging effect, plays a very important role for the power-electronics system quality and reliability. Therefore it is important to diagnosis monitoring the condition of an electrolytic capacitor in real-time to predict the failure. In this paper, the on-line remote diagnosis monitoring system for UPS DC link electrolytic capacitors using low-cost single-chip zigbee communication modules is developed. To estimate the health status of the capacitor, the equivalent series resistor(ESR) of the component has to be determined. The capacitor ESR is estimated by using RMS computation using BPF modeling of DC link ripple voltage/current. Zigbee-based hardware experimental results show that the proposed remote capacitor diagnosis monitoring system can be applied to UPS successfully.

• 한국정보통신학회논문지
• /
• 제16권7호
• /
• pp.1391-1396
• /
• 2012

본 연구에서는 해저의 반사면이나 흡음재와 같이 주파수에 따라 다른 특성을 가지는 매체를 수치적으로 모델링하였다. 기존의 흡음재 해석 등가회로 모델에 용량성 성분을 부가하기 위해 Debye polarization 기법을 적용하여 흡음재의 모델링을 하였다. 이 모델의 파라미터를 추정하기 위해 폴리우레탄이라는 흡음재의 흡음 주파수 특성을 이용하였다. 파라미터의 추정에는 non-linear least squares라는 비선형 최적화 기법을 사용하였다. 먼저 두께 25 mm의 폴리우레탄의 흡음재의 파라미터를 추정하였으며, 이 파라미터를 이용해 50 mm의 폴리우레탄의 특성을 모델링하는 것이 가능하였다. 이를 바탕으로 흡음재의 주파수에 따른 흡음 특성을 하나의 간단한 모델로 모델링하는 것이 가능함을 보였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권8호
• /
• pp.975-982
• /
• 2007

The single-phase switched reluctance motor(SRM) drive requires DC source which is generally supplied through a rectifier connected with a commercial source. The rectifier is consist of a diode full bridge and a filter circuit. Usually the filter circuit uses capacitor with large value capacitance to reduce ripple component of DC power. Although the peak torque ripple of SRM is small, the short charge and discharge current of the filter capacitor draws the low power factor and system efficiency. A modified single phase SRM drive system is presented in this paper, which includes drive circuit realizing reduction of torque ripple and improvement of power factor. In the proposed drive circuit, one switching part and diode which can separate the output of AC/DC rectifier from the filter capacitor is added. Also, a upper switch of drive circuit is exchanged a diode in order to reduce power switching device. Therefore the number of power switch device is not changed, two diodes are only added in the SRM drive. To verify the proposed system, some simulation and experimental results are presented.

• 전력전자학회논문지
• /
• 제22권4호
• /
• pp.369-372
• /
• 2017

This paper presents a control scheme for three-level NPC inverters using small DC-link capacitors. To reduce the inverter system volume, the film capacitor with small capacitance is a promising candidate for the DC-link. When small capacitors are applied in a three level inverter, however, the AC ripple component increases in the DC-link NPV (neutral point voltage). In addition, the three-phase input grid currents are distorted when the DC-link capacitors are fed by diode rectifier. In this paper, the additional circuit is applied to compensate for small capacitor systems defect, and the offset voltage injection method is presented for the stabilization in NPV. These two proposed processes evidently ensure the quality improvement of the input grid currents and output load currents. The feasibility of the proposed method is verified by experimental results.