• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.109-112
• /
• 2005

Cu계$I-III-VI_2$화합물은 직접천이형 반도체로 광흡수계수가 매우 높아 박막형 태양전지 제조에 매우 유리하다 또한 화학적으로 안정하며 Ga, A1등을 첨가하면 에너지 금지대폭을 조절할 수 있어 Wide Bandgap 태양전지 및 탠덤구조 태양전지를 제조하기에도 용이하다. $CuInSe_2(CIS)$ 물질에서 In을 $20-30\%$ 정도 치환한 $Cu(In,\;Ga)Se_2(CIGS)$ 태양전지의 경우 $19.5\%$의 세계 최고 효율을 보고하고 있으며 이는 다결정 실리콘 태양전지의 효율과 비슷한 수준이다. 본 연구에서는 동시 진공증발법을 이용하여 증착한 CIGS 박막 및 $CuGaSe_2(CGS)$ 박막을 이용하여 태양전지를 제조하였다. 공정의 재현성 및 결정립계가 큰 광흡수층 제조를 위하여 실시간 기판 온도 모니터링 시스템을 도입하였으며 버퍼층으로는 용액성장한 CdS 박막을 사용하였다. SLG/MO/CIGS(CGS)/CdS/ZnO/Al구조의 태양전지를 제조하여 면적 $0.5cm^2$에서 각각 $15\%$(CIGS)와 $7\%(CGS)$의 효율을 얻었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.160-162
• /
• 2009

We have prepared and characterized particle based CIGS thin films using a thermal evaporator. As the copper rate, selenium rate changed, CIGS particles were obtained at $240^{\circ}C$ for 6 hours from the reaction of $CuCl_2$, $InCl_3$, $GaCl_3$ and Se powder in solvent. The CIGS thin films were deposited on a sodalime glass. The CIGS thin film were identified to have a typical chalcopyrite tetragonal structure by using UV/Vis-spectroscopy, X-ray diffraction(XRD), Auger Electron Spectroscopy(AES), Scanning Electron Microscopy(SEM).

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.87-92
• /
• 2016

The effects of selenization pressure on the structural, optical and electrical properties of the CIGS thin films prepared by RF magnetron sputtering using a single quaternary target were investigated. At selenization pressures lower than atmospheric pressure, CIGS thin films formed non-stoichiometric compounds due to deficiencies of Se vapor. In contrast, when selenization process was conducted at above atmospheric pressure, the residence time of Se vapor inside the tube increased so that the Se element could be incorporated within vacant sites of the CIGS structure, resulting in the formation of stoichiometric CIGS thin films. High quality CIGS thin films could be obtained when the selenization process was performed at pressures greater than atmospheric and $550^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.322-322
• /
• 2007

• Current Photovoltaic Research
• /
• v.7 no.1
• /
• pp.1-8
• /
• 2019

The $Cu(In,Ga)Se_2$ (CIGS) thin film obtained by two-step process (metal deposition and Se annealing) has a rough surface morphology and many voids at the CIGS/Mo interface. To solve the problem a precursor that contains Se was employer by depositing a (In,Se)/(Cu,Ga) stacked layer. We devised a two-step annealing (vacuum pre-annealing and Se annealing) for the precursor because direct annealing of the precursor in Se environment resulted in the small grains with unwanted demarcation between stacked layers. After vacuum pre-annealing up to $500^{\circ}C$ the CIGS film consisted of CIGS phase and secondary phases including $In_4Se_3$, InSe, and $Cu_9(In,Ga)_4$. The secondary phases were completely converted to CIGS phase by a subsequent Se annealing. A void-free CIGS/Mo interface was obtained by the two-step annealing process. Especially, the CIGS film prepared by vacuum annealing $450^{\circ}C$ and subsequent Se annealing $550^{\circ}C$ showed a densely-packed grains with smooth surface, well-aligned bamboo grains on the top of the film, little voids in the film, and also little voids at the CIGS/Mo interface. The smooth surface enhanced the cell performance due to the increase of shunt resistance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.295-295
• /
• 2010

Nanoparticles of the compound semiconductor, Cu(In, Ga)Se2 (CIGS), were synthesized in solution under ambient pressure below $100^{\circ}C$ and characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption spectroscopy and energy-dispersive X-ray (EDX) analyses. These materials have chalcopyrite crystal structures and the particle sizes less than 100 nm. Synthetic conditions were studied for the crystallized CIGS nanoparticles formation to prevent from side products of Cu2Se, Cu2-xSe, and CuSe etc. The single phase CIGS nanoparticles were applied to coating of thin films photovoltaic cells. The electro deposition of CIGS thin films is also a good non-vacuum technology and under investigation. In aqueous solutions, the different chemical compositions of CIGS thin films were obtained, depending on pH, concentration of starting materials and deposition potentials. The surface morphology of the prepared CIGS thin films depends on the complexing ligands to the solutions during the electrochemical deposition.

• Current Photovoltaic Research
• /
• v.5 no.1
• /
• pp.28-32
• /
• 2017

In this paper, (Ga,Al):ZnO layers were deposited by sputtering to evaluate the device performance according to the thickness of the layer. As the thickness increased, low transmittance was observed, but the electrical resistance was improved. On the other hand, the highest efficiency was recorded at 400 nm device than a 500 nm of it. Therefore, since the critical thickness exists, it is necessary to set an adequate TCO layer thickness in consideration of the characteristics of the underlying film and the device.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1129-1134
• /
• 2015

In this article, a study of a flower like nanostructured CdS buffer layer for improving the performance of a submicron-thick $CuIn_{1-x}Ga_xSe_2$ (CIGS) solar cell (SC) is presented. Both its synthesis and properties are discussed in detail. The surface reflectance of the device is dramatically decreased. SCs with flower like nanostructured CdS buffer layers enhance short-circuit current density, fill factor, and open-circuit voltage. These enhancements contribute to an increase in power conversion efficiency of about 55% on average compared to SCs that don't have a flower like nanostructured CdS buffer layer, despite them both having the same CIGS light absorbing layer.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.89-93
• /
• 2017

For various process pressures, aluminum doped zinc oxide(AZO) films were deposited by in-line pulsed-DC sputtering. The deposited AZO films were optically and electrically investigated and analyzed for the window layers of CIGS solar cell systems. As the pressure was increased from 9 mtorr to 15 mtorr, the thickness of AZO was decreased as a result of scattering and its sheet resistance was rapidly increased. The transmittance of AZO was slightly decreased as the pressure was increased and the calculation of figure of merit(F.O.M) was dependent on the sheet resistance. The structural characteristics of AZO thin films analyzed by X-ray diffraction(XRD) showed no significant dependency according to the pressure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.275-275
• /
• 2012

The relative composition of $Cu(InGa)Se_2$ solar cells is one of the most important measurement issues. However, quantitative analysis of multi-component alloy films is difficult by surface analysis methods due to severe matrix effect. In this study, quantitative depth profiling analysis of CIGS films was investigated by secondary ion mass spectrometry (SIMS). The compositions were measured by SIMS using the alloy reference relative sensitivity factors derived from the certified compositions and the total counting numbers of each element. The compositions measured by SIMS were linearly proportional to those by inductively coupled plasma-mass spectrometry (ICP-MS) using isotope dilution method. In this study, the quantification measured by ICP-MS method is compared with the composition calculated by SIMS depth profiles with AR-RSFs obtained from the reference. The SIMS depth profile of CIGS thin films according to the manufacturing condition was converted into compositional depth profile.