• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.147-153
• /
• 2014

This study was performed to evaluate the effect of surface roughness on pump performance. To this end this, using commercial codes, ANSYS CFX and BladeGen, we simulated pump performance in terms of efficiency, head and shaft power, both with and without surface roughness. Finally simulation and experiment results were compared for a quantitative analysis. The results of this comparison showed that surface roughness led to an about 7% reduction in pump efficiency.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.3
• /
• pp.694-703
• /
• 2017

Many residents living near the cement factories are facing unpleasant odors. Thus, various efforts have been attempted to reduce the emission of odorous compounds from the cement manufacturing processes. This study focused on analysis of Acetaldehyde and their dispersion in vicinity of the residential area using theoretical calculation such as numerical simulation and dispersion model. The most significant odor species was acetaldehyde indicating 2 ppb at the test point, and the estimated concentration was similar to the value by Calpuff calculation. The modelling work revealed the emission source of the factory to influence the test site.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.74-77
• /
• 2011

A mixing characteristics on recess length change of Gas-centered swirl coaxial injector using high-performance staged combustion rocket engine carry out study through CFD(Computational fluid dynamics). propellant phase that combined gas-liquid simulate gas-gas. In order to measure spreading angle, velocity distribution to injector exit and spray structure of propellant analyzed. Axial velocity increase by increasing recess length, but tangential velocity decrease. The result confirmed qualitative characteristics that the spreading angle decreases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.745-749
• /
• 2011

Two-dimemsional liquid-solid multiphase fluid dynamics was used to analyze the suspension and mix of liquid fuel and solid particles in fuel tank installed mixing impeller. In this paper, the multiphase flow was modeled using Eulerian Grandular Multiphase model. Experimental measurements of the axial distribution of solids concentration in stirred tanks under 12vol% solid loading were used for comparison with the CFD simulation. Four cases for the impeller location and flow pumping direction also were reviewed under 10.5% solids loading and 700rpm in fuel mix tank. The result of quality of suspension was compared with each cases and the impeller location and operation of mixing fuel tank was established.

• Journal of Korea Multimedia Society
• /
• v.15 no.3
• /
• pp.380-387
• /
• 2012

The present investigation is to examine the thermal behaviors of air flows inside Korean traditional house made of the construction materials transmitted. The methodology is numerical predictions of air flows depend on the temperature distribution inside the indoor spaces. The transient computational simulations are performed along with the different house types, weather condition, and operating time. Thermal properties of building units have been obtained by the parallel measurements and utilized in the numerical works. Consequently, the details of flows and temperature of air in the houses illustrate the thermal design of the traditional Korean house satisfy the requirements of human living.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.99-103
• /
• 2003

An analysis of the flow within supersonic turbine cascades is necessary to design and manufacture turbo-pump system. Because of the differences between the specified inlet boundary value and the computed inlet value caused by the far field inlet boundary condition, the computations at desired inlet conditions can not be achieved. So, this paper studied the problem occurred when far field inlet conditions were specified as inlet boundary conditions. And the numerical analyses using Fine Turbo, CFD Program, has been performed and compared with those of experiments when a converging-diverging nozzle or a linear nozzle was located in front of cascades instead of the far field inlet condition.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.186-190
• /
• 2006

This study was performed to investigate the characteristics of a co-axial swirl injector. Especially to predict the initial liquid sheet thickness and spray cone angle of an outer orifice a concept of effective area was introduced from hydraulic analysis. In addition, the parameters determining the characteristics of a co-axial swirl injector were re-defined around outer orifice. The calculated results-SMD, spray cone angle, and spray thickness agreed well with the test results qualitatively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.246-253
• /
• 2013

This paper addresses the technology of active flow control for stabilizing a flow field. In order for flow field modeling from the control point of view, the huge-data set from CFD(computational fluid dynamics) are reduced by using a POD(Proper Orthogonal Decomposition) method. And then the flow field is expressed with dynamic equation by low-order modelling approach based on the time and frequency domain analysis. A neural network flow estimator from the pressure information measured on the surface is designed for the estimation of the flow state in the space. The closed-loop system is constructed with feedback flow controller for stabilizing the vortices on the flow field.

• Journal of computational fluids engineering
• /
• v.20 no.1
• /
• pp.10-15
• /
• 2015

In this study, the characteristics of water treatment mixer with various propeller profiles are numerically invesitgated. The computation was conducted by solving the incompressible Navier-Stokes equations on unstructured tetrahedral elements with k-${\varepsilon}$ turbulence model. It was found that the spreading angle and swirl magnitude of the jet are important factors for the mixer efficiency, since they clearly characterize the propeller and the frontal surface area of the propeller but not so much affected by the skew angle if it exceeds 30 degrees. The case1 and case2 models are found to show the best propeller efficiency. The case2 with low blade angle, however, requires the lowest power input for the same discharge capacity as the case1.

• Journal of computational fluids engineering
• /
• v.17 no.1
• /
• pp.61-69
• /
• 2012

In this paper, the shape design process is briefly discussed emphasizing the use of topology optimization in the conceptual design stage. The basic idea is to view feasible domains for sensitivity region concepts. In this method, the main process consists of two steps: as the design moves further inside the feasible domain using Taguchi method, and thus becoming more successful topology optimization, the sensitivity region becomes larger. In designing a double-eccentric butterfly valve, related to hydrodynamic performance and disc structure, are discussed where the use of topology optimization has proven to dramatically improve an existing design and significantly decrease the development time of a shape design. CFD analysis results demonstrate the validity of this approach.