• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.121-130
• /
• 2003

The purpose of this study was to evaluate the possibile clinical application of electroplating to increase diameter of an orthodontic wire, through examining the change of physical properties. The diameter of stainless steel orthodontic wire was increased from 0.016 inch to 0.018 inch by electroplating in a bath of nickel sulfate 100g/L, nickel chloride 60g/L, boric acid 30g/L, and sodium chloride 50g/L, under the conditions of 1.7V, $25\~29^{\circ}C\;and\;3.1\~3.3pH$. During the electroplating, the rate of diameter increase was measured every minute. To investigate uniformity, the diameter was measured at three different locations of each wire specimen aster electroplating. An X-ray diffraction test was performed to analyze the nature of the electroplated metal. Following heat treatment to improve adhesion between the wire and electroplated metal, a three-point bending test was conducted to compare stiffness, field strength, and ultimate strength among four wire groups; 0.016 inch, electroplated 016, electroplated and heat-treated 016, and 0.018 inch wires. Through the comparison of each wire group, following results were obtained. 1. In the load-deflection graph, the curve of the electroplated group was Placed between that of the 0.016 inch group and the 0.018 inch group, and the owe was closer to the 0.018 inch group by heat treatment. 2. In the electroplated and heat-treated 016 wire group, the values of stiffness, yield strength and ultimate strength showed higher tendency than in the original 0.016 Inch group. Stiffness and ultimate strength showed statistically significant differences between two groups. 3. Stiffness, yield strength, and ultimate strength of electroplated wire presented lower values than those of 0.018 inch wire group. 4. Stiffness, yield strength, and ultimate strength of electroplated and heat-treated wire showed higher tendency than those of electroplated wire group, and ultimate strength showed statistically significant difference between two groups. 5. After electroplating, the difference in diameter between the three locations was within $0.1\~0.3\%$ variation, and showed no statistical significance.

• Economic and Environmental Geology
• /
• v.35 no.3
• /
• pp.241-255
• /
• 2002

The purpose of this study is to investigate environmental geochemical characteristics for the acid mine drainage and stream sediments in the abandoned Honam coal mine area. For the chemical analysis, stream winter samples were collected at 54 sites and for the mineralogical and chemical analysis, stream sediments samples were collected at 34 sites. Physical and chemical characteristics of stream water were measured at the site and chemical compositions were analyzed by ICP-AES, ICP-MS and IC. Mineralogical characteristics of stream sediments samples were determined using XRD, SEM and EDS. In physical and chemical properties, stream water shows thats pH 2.85~8.12, Eh -62~215 mV, EC 0.205~146 ms/m, ER 0.234~255 {$\Omega}{\cdot}$m, DO 0.03~1068 mg/L and TDS 10.96~1420mg/L. In chemical compositions, we obtain that K 0.118~3.184 mg/L, Mg 2.1~114.48 mg/L, Ca 2.59~l25.02 mg/L, Al 0.01~44.72 mg/L, Fe 0.108~89.49 mg/L and Na 5.45~125.41 mg/L. Stream sediments are commonly composed of quartz, illite and goethite in the result of x-ray diffraction. After heat treatment at 98$0^{\circ}C$, the hematite peaks are distinctly shown. In consideration of heavy metals (include Fe) for steam sediments, Fe ranges 22575~34713 ppm, Zn 41.66~970.3 ppm, Cd 0.52~52.07 ppm, Cu 1.25~198.5 ppm and Pb 0.43~77.35 ppm.

• Korean Journal of Food Science and Technology
• /
• v.50 no.2
• /
• pp.191-197
• /
• 2018

This study investigated the influence of starch extraction (ST-EX) solutions on the extraction yield and characteristics of Chinese yam (CY) starches from domestic Dioscorea batatas. Ascorbic acid (VitC), $Na_2S_2O_3$, $NaHCO_3$, and $Na_2CO_3$ were used as ST-EX solutions (0.4%, w/v). The extracted CY starches were examined for ST-EX yield, chemical composition, size distribution, X-ray diffraction, solubility, swelling power, gelatinization, and pasting viscosity. The highest ST-EX yield was obtained from $NaHCO_3$, followed by VitC. Lower protein content, relative crystallinity, and gelatinization enthalpy were found in CY starches from alkaline ST-EX solutions ($NaHCO_3$ and $Na_2CO_3$). Size distribution and gelatinization temperature did not generally differ for CY starches from the different ST-EX solutions. Pasting viscosities increased in the order from $Na_2CO_3$ > $Na_2S_2O_3$ > $NaHCO_3$ > VitC ST-EX solutions. Thus, VitC may be most appropriate to extract CY starch from Dioscorea rhizomes, considering its ST-EX yield, total starch content, and variation in pasting viscosity.

• Journal of Radiation Protection and Research
• /
• v.20 no.1
• /
• pp.45-52
• /
• 1995

This study is to compare A point doses in human pelvic phantom by film dosimetry, computer planning and manual calculation by using of along-away table. We developed tissue equivalent human pelvic phantom composed of four pieces of cylindrical acryl tubes with water, to simulate intracavitary radiation (ICR) in patients with cervix cancer. When the phantom assembled from 4 pieces, it has a small space for inserting Fletcher-Suit-Delclos applicator like a human vagina. Fletcher-Suit-Delclos applicator inserted into the space was packed tightly with furacin gauzes, and three $^{137}Cs$ sources with radioactivity of $15.7mg\;Ra-eq$ were inserted into the tandem. For the film dosimetry, two pieces of X-OMAT V film (Kodak Co.) of which planes include point A, were arranged orthogonally in the slits between phantoms. A point dose and iso-dose curves were measured by means of optical densitometer. A point doses by film dosimetry, RTP system and manual calculation by using of along-away table were compared, and iso-dose curves by film dosimetry and computer planning were also compared. The dose of A point was 51.2cGy/hr by film dosimetry, 46.7cGy/hr by RTP system and 47.9 cGy/hr by along-away table. A point dose by computer planning was similar to the dose by calculation using of along-away table with acceptable accuracy $({\pm}3%)$, however, the dose by film dosimetry was different from two others with about 10% error. Since most clinical beams contains a scatter component of low energy photons, the correlation between optical density and dose becomes tenuous. In addition, film suffers from several potential errors such as changes in processing conditions, interfilm emulsion differences, and artifacts caused by air pockets adjacent to the film. For these reasons, absolute dosimetry with film is impractical, however, it is very useful for checking qualitative patterns of a radiation distribution. In future, solid state dosimeter such as TLD must be used for the dosimetry of ionizing radiation. When considerable care is used, precision of approximately 3% may be obtained using TLD.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.116-116
• /
• 2007

21 세기에 접어들면서 인터넷을 통한 정보 통신의 발달과 개인 휴대용 이동 통신기기의 활발한 보급에 따라 휴대형 전자기기들의 소형화와 고성능화로 나아가고 있다. 이러한 전자기기에 사용될 IC의 내장 메모리 또한 집적화 및 고속화, 저 전력화가 이루어져야 한다. 이러한 전자기기들에 필수적인 압전 세라믹스 부품 중 압전 부저 및 기타 음향 부품등을 각종 전자기기와 무선 전화기에 채택함으로써 압전 부품에 대한 수요와 생산이 계속 증가할 것으로 전망된다. 이처럼 압전 세라믹스를 이용한 그 응용 범위는 대단히 방대하며, 현재 모든 압전 부품들은 PZT 계열 재료로 만들어지고 있고, 차후 모두 비납계열 재료로 대체될 것이 확실시된다. Pb의 환경오염은 이미 오래전부터 큰 문제점으로 인식되고 있었으며 그 일례로 미국의 캘리포니아 주에서는 1986년부터 약 800종의 유해물질, 그 중에서도 Pb 사용을 300ppm 이하로 규제하는 Proposition 65를 제정하여 실행하고 있다. 그리고 2003년 2월에 EU (European Union) 에서 발표한 전자산업에 관한 규제 사항중 하나인 위험물질 사용에 관한 지칭 (Restriction of Hazardous Substance, RoHS) 에 의하면, 2006 년 7월부터 전기 전자 제품에 있어서 위험 물질인 Pb을 포함한 중금속 물질(카드늄, 수은, 6가 크롬, 브롬계 난연재)의 사용을 금지한다고 발표하였다. 비록 전자세라믹 부품에 함유된 Pb는 예외 사항으로 두었지만 대체 가능한 물질이 개발되면 전자세라믹 부품에서도 Pb의 사용을 금지한다고 규정하였다. 더욱이 일본은 2005 년부터 Pb 사용을 금지시켰다. 이와 같이 Pb가 환경에 미치는 영향 때문에 비납계 강유전 물질 및 압전 세라믹스 재료에 대한 연구가 전 세계적으로 활발히 진행되고 있다. 본 연구에서는 비납계 강유전체의 patterning을 위해서, NKN 박막을 고밀도 플라즈마원인 ICP를 이용하여 식각 mechanism을 연구하고, 식각변수에 따른 식각 공정을 최적화에 대하여 연구하였다. 가스 혼합비에 따라 식각 할때 700 W의 RF 전력과 - 150 V의 직류 바이어스 전압을 인가하였고, 공정 압력은 2 Pa, 기판 온도는 $23^{\circ}C$로 고정하였다. 식각 속도는 Tencor사의 Alpha-step 500을 이용하여 측정되었으며 식각 시 NKN 박막 표면과 라디칼과의 화학적인 반응을 분석하고 식각 메커니즘을 규명하기 위하여 XPS(x-ray photoelectron spectroscopy)를 사용하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.348-351
• /
• 2003

산소 과전압이 낮은 $MnO_2$를 촉매로 사용하여 반도체 산화물계의 산소선택성 전극을 제조하고 산화물 coating층의 미세구조와 전기화학적 특성을 분석하였다. Ti 기판에 열분해 법을 이용하여 $MnO_2$ 피막을 형성하였고, 또한 PVDF : $MnO_2$의 함량비를 1 : 1에서 1 : 40까지 정량적으로 변화시키고 DMF의 함량을 각각의 고정된 PVDF : $MnO_2$의 함량비에서 변화시켜 Pb전극에 1.5 mm/sec의 속도로 5회 dipping하여 $MnO_2$ 피막층을 형성 하였다. $450^{\circ}C$에서 1시간 열분해하여 약 $1\;{\mu}m$의 $MnO_2$ 피막층이 형성되었으나 Ti 기판과의 접착력이 약하여 피막자체에 대한 전기화학적 특성을 관찰할 수 없었다. PVDF : DMF = 4 : 96인 경우 pb 전극의 피막층이 얇기 때문에 박리현상이 일어났으며 이는 산화물 용제의 낮은 점도 때문인 것으로 판단된다. 또한 PVDF : DMF = 10 : 90의 경우는 5회 dipping 하여 약 $150\;{\mu}m$의 피막층을 형성하였다. PVDF : $MnO_2$의 함량비가 1:1에서 1:6 까지는 DMF의 함량에 무관하게 전극 특성이 나타나지 않았지만 $MnO_2$의 양이 상대적으로 증가하면 cycle이 증가하더라도 거의 일정한 전류 값을 갖고 $MnO_2$와 PVDF의 비가 20:1 이상의 조성에서는 균일한 CV 특성을 나타냈다. 이는 $MnO_2$가 효과적으로 촉매 작용을 한 것으로 판단되며 anodic polarization에 의한 산소 발생 과전압도 약 1.4V 정도로 감소되었다.동등한 MSIL 코드를 생성하도록 시스템을 컴파일러 기법을 이용하여 모듈별로 구성하였다.적용하였다.n rate compared with conventional face recognition algorithms. 아니라 실내에서도 발생하고 있었다. 정량한 8개 화합물 각각과 총 휘발성 유기화합물의 스피어만 상관계수는 벤젠을 제외하고는 모두 유의하였다. 이중 톨루엔과 크실렌은 총 휘발성 유기화합물과 좋은 상관성 (톨루엔 0.76, 크실렌, 0.87)을 나타내었다. 이 연구는 톨루엔과 크실렌이 총 휘발성 유기화합물의 좋은 지표를 사용될 있고, 톨루엔, 에틸벤젠, 크실렌 등 많은 휘발성 유기화합물의 발생원은 실외뿐 아니라 실내에도 있음을 나타내고 있다.>10)의 $[^{18}F]F_2$를 얻었다. 결론: $^{18}O(p,n)^{18}F$ 핵반응을 이용하여 친전자성 방사성동위원소 $[^{18}F]F_2$를 생산하였다. 표적 챔버는 알루미늄으로 제작하였으며 본 연구에서 연구된 $[^{18}F]F_2$가스는 친핵성 치환반응으로 방사성동위원소를 도입하기 어려운 다양한 방사성의 약품개발에 유용하게 이용될 수 있을 것이다.었으나 움직임 보정 후 영상을 이용하여 비교한 경우, 결합능 변화가 선조체 영역에서 국한되어 나타나며 그 유의성이 움직임 보정 전에 비하여 낮음을 알 수 있었다. 결론: 뇌활성화 과제 수행시에 동반되는 피험자의 머리 움직임에 의하여 도파민 유리가 과대평가되었으며 이는 이 연구에서 제안한 영상정합을 이용한 움직임 보정기법에 의해서 개선되었다. 답이 없는 문제, 문제 만들기, 일반화가 가능한 문제 등으로 보고, 수학적 창의성 중 특히 확산적 사고에 초점을 맞추어 개방형 문제가 확산적 사고의 요소인 유창성, 독창성, 유연성 등에 각각 어떤 영향을 미치는지 20주의 프로그램을 개발, 진행하여 그 효과를 검증하고자

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.1-33
• /
• 1997

The objective of this study was to analyze the in vitro and in vivo corrosion products of low and high copper amalgams. The four different types of amalgam alloy used in this study were Fine cut, Caulk spherical, Dispersalloy, and Tytin. After each amalgam alloy and Hg were triturated according to the directions of the manufacturer by means of the mechanical amalgamator(Amalgam mixer. Shinhung Co. Korea), the triturated mass was inserted into a cylindrical metal mold which was 12mm in diameter and 10mm in height. The mass was condensed by 150Kg/cm compressive force. The specimen was removed from the mold and aged at room temperature for about seven days. The standard surface preparation was routinely carried out by emery paper polishing under running water. In vitro amalgam specimens were potentiostatically polarized ten times in a normal saline solution at $37^{\circ}C$(potentiostat : HA-301. Hukuto Denko Corp. Japan). Each specimen was subjected to anodic polarization scan within the potential range -1700mV to+400mV(SCE). After corrosion tests, anodic polarization curves and corrosion potentials were obtained. The amount of component elements dissolved from amalgams into solution was measured three times by ICP AES(Inductive Coupled Plasma Atomic Emission Spectrometry: Plasma 40. Perkim Elmer Co. U.S.A.). The four different types of amalgam were filled in occlusal and buccal class I cavities of four human 3rd molars. After about five years the restorations were carefully removed after tooth extraction to preserve the structural details including the deteriorated margins. The occlusal surface, amalgam-tooth interface and the fractured surface of in vivo amalgam corrosion products were analyzed. In vivo and in vitro amalgam specimens were examined and analyzed metallographically by SEM(Scanning Electron Microscope: JSM 840. Jeol Co. Japan) and EDAX(Energy Dispersive Micro X-ray Analyser: JSM 840. Jeol Co. Japan). 1. The following results are obtained from in vitro corrosion tests. 1) Corrosion potentials of all amalgams became more noble after ten times passing through the in vitro corrosion test compared to first time. 2) After times through the test, released Cu concentration in saline solution was almost equal but highest in Fine cut. Ag and Hg ion concentration was highest in Caulk spherical and Sn was highest in Dispersalloy. 3) Analyses of surface corrosion products in vitro reveal the following results. a)The corroded surface of Caulk spherical has Na-Sn-Cl containing clusters of $5{\mu}m$ needle-like crystals and oval shapes of Sn-Cl phase, polyhedral Sn oxide phase. b)In Fine cut, there appeared to be a large Sn containing phase, surrounded by many Cu-Sn phases of $1{\mu}m$ granular shapes. c)Dispersalloy was covered by a thick reticular layer which contained Zn-Cl phase. d)In Tytin, a very thin, corroded layer had formed with irregularly growing Sn-Cl phases that looked like a stack of plates. 2. The following results are obtained by an analysis of in vivo amalgam corrosion products. 1) Occlusal surfaces of all amalgams were covered by thick amorphous layers containing Ca-P elements which were abraded by occlusal force. 2) In tooth-amalgam interface, Ca-P containing products were examined in all amalgams but were most clearly seen in low copper amalgams. 3) Sn oxide appeared as a polyhedral shape in internal space in Caulk spherical and Fine cut. 4) Apical pyramidal shaped Sn oxide and curved plate-like Sn-Cl phases resulted in Dispersalloy. 5) In Tytin, Sn oxide and Sn hydroxide were not seen but polyhedral Ag-Hg phase crystal appeared in internal space which assumed a ${\beta}_l$ phase.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.313-313
• /
• 2009

OLED 소자는 직접발광, 광시야각, 그리고 빠른 응답속도 때문에 동영상에 적합하여 최근 각광받고 있는 디스플레이장치 중의 하나이다. OLED 소자의 양극재료로는 높은 광투과율과 $\sim10^{-4}{\Omega}\;cm$ 수준의 낮은 전기 비저항을 갖는 ITO (Sn-doped $In_2O_3$)가 널리 사용되고 있다. 하지만 원료 물질인 인듐의 수급량 부족으로 인한 문제점과 독성, 저온증착의 어려움, 스퍼터링시 음이온 충격에 의한 막 손상으로 저항의 증가의 문제점이 있고, 또한 액정디스플레이의 투명전극으로 사용될 경우 $400\;^{\circ}C$정도의 높은 온도와 수소 플라즈마 분위기에서 장시간 노출 시 열화로 인한 광학적 특성변화가 문제가 된다. 반면에 Al이 도핑 된 ZnO (AZO)박막은 넓은 밴드갭 (3.37eV)와 400nm에서 700nm 사이의 가시광 영역에서 80% 이상의 우수한 투과성을 지니고 있다. 특히 Al이 도핑된 ZnO는 박막의 전기적 특성이 크게 향상되어 디스플레이나 태양전지로의 응용이 가능하다. 또한 비교적 낮은 비용과 플라즈마에서의 안정성, 무독성, 그리고 전기전도성과 같은 많은 이점이 있다. 그 결과 AZO 박막은 ITO기판을 대안하는 지원물질로 활발히 연구가 진행되고 있다. 본 연구에서는 TCO 박막의 면 저항과 표면 거칠기에 따른 OLED 소자의 특성을 분석하였다. ITO와 AZO 박막은 챔버 내 다양한 가스 분위기(Ar, Ar+$O_2$ and Ar+$H_2$)에서 R.F Magnetron Sputtering방법으로 증착하였다. TCO 박막의 구조적인 이해를 돕기 위해서 X-ray diffraction 과 FESEM으로 분석하였다. 광학적 투과도와 박막의 두께는 ultraviolet spectrophotometer (Varian, cary-500)와 surface profile measurement system으로 각각 측정하였다. 면저항 charge carrier 농도, 그리고 TCO 박막의 이동도와 같은 전기적특성은 four-point probe와 hall effect measurement(HMS-3000)로 각각 측정하였다. TCO 박막의 표면 거칠기 조절을 위해 photo lithography 공정을 사용하여 TCO 박막을 화학에칭 하였다. 미세사이즈 패턴 마스크가 사용되었으며 에칭의 깊이는 에칭시간에 따라 조절하였다. TCO 박막의 표면 형태는 FESEM과 AFM으로 관찰하였다. 투명전극으로 사용되는 ITO 및 AZO 기판 상용화를 위해 ITO 및 AZO 기판 위에 ${\alpha}$-NPB, Alq3, LiF, Al 의 순서로 증착 및 패터닝함으로써 OLED 소자를 제작하였다. 전류밀도와 전압 그리고 발광휘도와 전압과 같은 전기적 특성은 spectrometer(minolta CS-1000A)를 이용하여 측정하였다.

• Journal of agriculture & life science
• /
• v.45 no.3
• /
• pp.25-33
• /
• 2011

This study was conducted to examine genetic variation on leaf characteristics of Machilus thunbergii populations. Ten populations were subjected to multivariate analysis for 9 characteristics of leaf morphology. Average length of leaf blade, leaf width, petiole length, vein number were 9.8cm, 4.0cm, 1.8cm, 8.4 respectively, while angle of leaf base and leaf apex were $67.9^{\circ}$ and $78^{\circ}$ respectively. The coefficient of variation (C.V.) on leaf characteristics was 20% which indicate similar features among the populations. Nested analysis showed statistically signigicant differences among populations as well as among individuals within populations. Genetic relationship between populations using complete linkage method showed four groups to Euclidean distance 1.2 and did not show a tendency to cluster into the same group. There were three principal components that had a meaningful eigenvalue over 1.0 among the 9 components. The explanatory power of the top three main components on the total variation was 92.8%. The first principal component (PC) was explained about 40.3% which is mainly correlated with maximum leaf width and the second PC was explained about 28.7% which is correlated with leaf blade length. The third PC was explained about 23.8% which is correlated with petiole length ($X_3$). These characters were important factors for analysis of the relationship among natural populations of M. thunbergii.

• Journal of Sasang Constitutional Medicine
• /
• v.8 no.1
• /
• pp.377-393
• /
• 1996

Lumbago is the common disease in the human, many people have been sicked the Lumbago. As the traditional methods of Lumbago treatment, acupuncture, moxibustion, herb medicines have been applied to a patient, nowadays, new methods have been applied physical remedy, Yakchim (Korean herb acupuncture) remedy, Chuna remedy to. This report was collected 73 Lumbago patients by name, sex, age, motive, symptoms, X-ray, CT, MRI, lRCT, Sasang constitution type, Sasang herb medicine, Yakchim, Chuna, period of remedy, satisfaction of remedy, at the "WooRee Korean Medical Clinic" during 21 months from Sep. 14, 1994 to May 25, 1996. And this report was studied about the distribution of the Sasang constitution type, the Sasang herb medicine, the effect, the period. The results were as follows: 1. Lumbago patients were distributed like that; Taeum-ln (太陰人) 47 (66.3 %), Soyang-In 16 (21.9 %), Soum-In (13.7 %), Taeyang-In (太陽人) 0. This was different from distribution of Donguisuseibowon (東醫壽世保元), Taeum-In (太陰人) 50%, Soyang-In (少陽人) 30 %, Soum-In (少陰人) 20 %, Taeyang-In (太陽人) little, this report shows that the number of Taeum-In (太陰人) is more than that of Donguisuseibowon and the number of Soum-In is less than that of Donguisuseibowon. 2. The average satisfaction of remedy was 60.3 %, Taeum-In's satisfaction was 66.0 %, Soum-In's satisfaction was 56.3 %, Soyang-In's satisfaction was 60.0 %. 3. The effective herb medicines were as follows, Soyang-In used the Hyong Bang Ji Hwang Tang (荊防地黃湯), Yuk Mi Ji Hwang Tang (六味地黃樓), Soum-In used the Sib Yi Mi Goan Jung Tang (十二味寬中湯), Taeum-In used the Chung Sim Yon Ja Tang (淸心蓮子陽), Chung Pae Sa Gan Tang (淸師爾肝湯), Yeol Da Han So Tang (熱多寒少湯). 4. The period of remedy was about 6 weeks. The period of remedy of each types was as follows, Taeum-In was about 5.7 weeks, Soum-In was about 6.8 weeks, Soyang-In was about 4.2 weeks. 5. The method of Lumbago remedy is divided three types, sprain Lumbago, Pyobyong (表病 : outside Syndromes) Libyong (裡病 : inside symdromes). Soum-In's methods are Pyobyong's ascending the Yang (陽), adding the Gi (氣) [升陽益氣], and Libyong's descending the inside Yim (裡陰) [裡陰降氣], Soyang-In's methods are Pyobyongs's decending the outside-Yim [表陰降氣], and Libyong's ascending the cool Yang (濟陽) [淸陽上升]. Taeum-In's methods are Pyobyong's ascending the Lung's Yang (肺陽升氣), and Libyong's colding the dried hot liver (淸肝燥熱). Taeyang's methods are strong the liver and making Yim. (補r肝生陰) 6. There are two methods for using the YakChim (Korean herb-acupuncture) by Sasang constitution medicine, one is to select the Yakchim, the other is to choice the point for appling the Yakchim. The first, to select the Yakchim, the other is follows; Soum-In can select the bee Venom, Soyang-In can select the H.O. (Hong Whoa 紅花), Taeum-In can select the I (Hodo 胡挑), V, O.K. (Ungdarn, 薦膽), Uwhang 牛黃, Sa-Hyang 麝香, etc., Palgang Yakchim (eight principles Korean herb-acupuncture (八剛藥鐵)) could made by abstracted Sasang herb medicine. The second, to choice the points for applying the Yakchim are used in the TaeGiuk Acupuncture method (太梗針法), Sacho (四焦, four warmer) by Sasang constritutional physiology and pathology.