• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1955-1961
• /
• 2012

In this work, the reactions of carbamyl and thiocarbamyl halides with $NH_3$ were studied in the gas phase at the MP2(FC)/6-31+G(d) level of theory. Single point calculations were performed at the QCISD/6-311+G(3df,2p) to refine the energetics. The reaction mechanisms were also studied in aqueous solution. The structures were fully optimized at the CPCM-MP2(FC)/6-31+G(d) and refined by a single point CPCM-QCISD/6-311+G(3df,2p) calculations. The reaction mechanisms for the title compounds were compared with those for the acetyl and thioacetyl halides. The lower reactivity of carbamyl (and thiocarbamyl) groups was explained by comparing the C=O and C=S ${\pi}$-bond strengths as well as resonance contributions in the ground state.

• Carbon letters
• /
• v.5 no.1
• /
• pp.12-17
• /
• 2004

In this study, the oxyfluorination of PAN-based carbon fibers was undertaken at room temperature using fluorine-oxygen mixtures, and the influence of oxyfluorination on properties was investigated. The surface characteristics of the modified fiber were determined by using X-ray photoelectron spectroscopy (XPS) and dynamic contact angle analyzer. The oxyfluorination of carbon fibers was one of the more effective methods to increase surface wettability by the formation of semicovalent C-F bond and C-O bond depending on reaction conditions. When oxygen mole fraction is increased from 0.5 to 0.9, it is probable that attached fluorine atoms at the surface of the fibers reacted with other components. As increased oxyfluorination time and decreased its pressures, semi-covalent peak is increased at 0.5 of oxygen mole fraction. The total surface free energy of oxyfluorinated carbon fibers decreased with increasing oxygen mole fraction over 0.5. These results indicate that the surface of carbon fibers became much more hydrophilic after the short oxyfluorination. The surface free energy of oxyfluorinated carbon fibers progressively decreased after 10 min treatment. The polar components of surface free energies were however, significantly higher for all oxyfluorinated samples than that for the untreated carbon fiber.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.09a
• /
• pp.219-225
• /
• 2002

This paper presents a novel "bumpless flip chip package"for cost! performance driven devices. Using the conventional electroplating and etching processes, this package enables the production of fine pitch BGA up to 256 I/O with single layer routing. An array of circuitry down to $25-50{\mu}{\textrm}{m}$ line/space is fabricated to fan-in and fan-out of the bond pads without using bumps or substrate. Various types of joint methods can be applied to connect the fine trace and the bond pad directly. The resin-filled terminal provides excellent compliancy between package and the assembled board. More interestingly, the thin film routing is similar to wafer level packaging whereas the fan-out feature enables high lead count devices to be accommodated in the BGA format. Details of the design concepts and processing technology for this novel package are discussed. Trade offs to meet various cost or performance goals for selected applications are suggested. Finally, the importance of design integration early in the technology development cycle with die-level and system-level design teams is highlighted as critical to an optimal design for performance and cost.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.344-350
• /
• 2010

The improved photocatalytic performance of a carbon/$TiO_2$ composite was studied for the Bisphenol A (BPA) decomposition. Titanium tetraisopropoxide (TTIP) and a rice husk from Korea were heterogeneously mixed as the titanium and carbon sources, respectively, for 3 h at room temperature, and then thermally treated at $600^{\circ}C$ for 1 h in $H_2$ gas. The transmission electron microscopy (TEM) images revealed that the bulk carbon partially covered the $TiO_2$ particles, and the amount that was covered increased with the addition of the rice husk. The acquired carbon/$TiO_2$ composite exhibited an anatase structure and a novel peak at $2{\theta}=32^{\circ}$, which was assigned to bulk carbon. The specific surface area was significantly enhanced to 123~164 $m^2/g$ in the carbon/$TiO_2$ composite, compared to $32.43m^2/g$ for the pure $TiO_2$. The X-ray photoelectron spectroscopy (XPS) results showed that the Ti-O bond was weaker in the carbon/$TiO_2$ composite than in the pure $TiO_2$, resulting in an easier electron transition from the Ti valence band to the conduction band. The carbon/$TiO_2$ composite absorbed over the whole UV-visible range, whereas the absorption band in the pure$TiO_2$ was only observed in the UV range. These results agreed well with an electrostatic force microscopy (EFM) study that showed that the electrons were rapidly transferred to the surface of the carbon/$TiO_2$ composite compared to the pure $TiO_2$. The photocatalytic performance of the BPA removal was optimized at a Ti:C ratio of 9.5:0.5, and this photocatalytic composite completely decomposed 10.0 ppm BPA after 210 min, whereas the pure $TiO_2$ achieved no more than 50% decomposition under any conditions.

• Bulletin of the Korean Chemical Society
• /
• v.7 no.6
• /
• pp.468-471
• /
• 1986

The isolated products from the reactions of $Rh(ClO_4)(CO)(PPh_3)_2$ (1) with CH_2$ = $CHCO_2C_2H_5$ (2) and trans-$CH_3CH$ = $CHCO_2C_2H_5$ (3) contain 80∼ 90% of $[Rh(CH_2 = CHCO_2C_2H_5)(CO)(PPh_3)_2]ClO_4$ (4) and [Rh(trans-$CH_3CH = CHCO_2C_2H_5(CO)(PPh_3)_2]ClO_4$ (5), respectively where 2 and 3 seem to be coordinated through the carbonyl oxygen. It has been found that complex 1 catalyzes the isomerization of $CH_2 = CH(CH_2)_8CO_2C_2H_5$ (6) to $CH_3(CH_2)_nCH = CH(CH_2)_{7-n}CO_2C_2H_5$ (n = 0∼7) under nitrogen at 25$^{\circ}C$. The isomerization of 6 is slower than that of $CH_2 = CH(CH_2)_9CH_3$ to $CH_3(CH_2)_nCH$ = $CH(CH_2)_{8-n}CH_3$ (n = 0∼8), which is understood in terms of the interactions between the carbonyl oxygen of 6 and the catalyst. It has been also observed that complex 1 catalyzes the hydrogenation of 2, 3, 6, trans-$C_6H_5CH = CHCO_2C_2H_5$ (7), $CH_3(CH_2)_7CH = CH(CH_2)_7CO_2C_2H_5$ (8) and $CH_2 = CH(CH_2)_9CH_3$ (9), and the isomerization (double bond migration) of 6 and 9 under hydrogen at 25$^{\circ}C$. The interactions between the carbonyl oxygen of the unsaturated esters and the catalyst affect the hydrogenation in such a way that the hydrogenation of the unsaturated esters becomes slower than that of simple olefins.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.5
• /
• pp.1539-1542
• /
• 2011

The aminolysis of O-methyl S-aryl thiocarbonates with benzylamines are studied in acetonitrile at -45.0$^{\circ}C$. The ${\beta}_X$(${\beta}_{nuc}$) values are in the range 0.62-0.80 with a negative cross-interaction constant, ${\rho}_{XZ}$ = -0.42, which are interpreted to indicate a concerted mechanism. The kinetic isotope effects involving deuterated benzylamine nucleophiles ($XC_6H_4CH_2ND_2$) are large, $k_H/k_D$ = 1.29-1.75, suggesting that the N-H(D) bond is partially broken in the transition state by forming a hydrogen-bonded four-center cyclic structure. The concerted mechanism is enforced by the strong push provided by the MeO group which enhances the nucleofugalities of both benzylamine and arenethiolate from the putative zwitterionic tetrahedral intermediate.

• Analytical Science and Technology
• /
• v.15 no.3
• /
• pp.317-320
• /
• 2002

The layer structure of the title compound, $[Ni(en)_2(H_2O)_2](CH_3C_6H_4SO_3)_2(H_2O)$ (en = ethylenediamine), consists of discrete cations, anions, and solvate water molecules linked by a hydrogen bonding network. The central Ni atom of the cation layer has a slightly distorted octahedral coordination geometry with the ethylenediamine ligands functioning as a N,N'-bidentate and the water ligands bonding through oxygen in a trans arrangement. The p-toluenesulfonate of the anion layer has an alternate sulfonate group directed toward opposite side of the cation layer. This layer structure is stabilized by a hydrogen bond involving the O atoms of the sulfonate, the water ligand, solvate water molecule, and the N atoms of the ethylenediamine.

• Journal of Power System Engineering
• /
• v.6 no.4
• /
• pp.56-61
• /
• 2002

This study is to investigate the wear behaviors of thermally sprayed ceramic coating by a pin-on-disk wear testing machine. The test specimens were plasma sprayed TiO2 coating material on carbon steel substrate(S45C) with Ni-4.5%Al alloy bond coating. Wear characteristics, friction coefficient and wear rates, were conducted at the three kinds of loads and velosities. Wear environments were dry and lubrication friction. The friction coefficients of TiO2 coating specimen in dry friction were almost same according to increase the friction velocity. The wear rate increased when the friction force is high. In lubrication friction, the wear hardly occured and friction coefficient was about 0.1. The adhesiveness of TiO2 in lubrication friction is larger than that in dry one.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.2
• /
• pp.120-125
• /
• 1995

Solid solutions of Pr2-xBaxNiO4±δ with K2NiF4-type structure were prepared in air and characterized by powder X-ray diffraction, Rietveld refinements, iodometry titrations, and conductivity measurements. The range of the solid solution was 0 ≤ x < 0.5. The crystal structure changes from orthorhombic (Fmmm) for x ≤ 0.1 to pseudo-tetragonal (I4/mmm) for x ≥ 0.2. The orthorhombic structure of x=0.1 transforms to tetragonal at low temperature. The bond distances obtained from the Rietvel analyses did not vary significantly with the Ba content except that of Ni-O (parallel to the c-axis) which showed an abrupt increase from x=0.1 to 0.2. The excess oxygen content (δ) decreases from 0.241 to 0.03 with increasing substituted Ba contents within the solution range. The samples are all semiconductors at the temperature range 4 < T < 300 K.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.4
• /
• pp.352-356
• /
• 1989

The crystal structure of maltitol, 4-O-${\alpha}$ -D-glucopyranosyl-D-glucitol, has been determined by X-ray diffraction method. The crystal is orthorhombic with cell parameters of a = 8.170(1), b = 12.731(1), c = 13.679(3) ${\AA}$, space group $P2_12_12_1$ and z = 4. The structure was solved by direct methods and refined to R = 0.030 for 1181 observed reflections measured on a diffractometer. The ${\alpha}$-glucose ring has chair conformation. The carbon atom chain of the glucitol residue has the bent, ap, Psc, Psc conformation. The angle at the ring oxygen atom is $112.6^{\circ}$ and the one at the glucosidic oxygen is $117.1^{\circ}$. The molecules are linked by very complicated hydrogen bonds, and there is an intramolecular hydrogen bond between O(1') and O(2').