• 한국표면공학회지
• /
• 제41권3호
• /
• pp.109-113
• /
• 2008

High strength 7xxx series Al-Zn-Mg alloy have been investigated for using light weight automotive parts especially for bump back beam. The composition of commercial 7xxx aluminum has the Zn/Mg ratio about 3 and Cu over 2 wt%, but this composition isn't adequate for appling to automotive bump back beam due to its high resistance to extrusion and bad weldability. In this study the Zn/Mg ratio was increased for better extrusion and Cu content was reduced for better welding. With this new composition we investigated the effect of composition on the resistivity against stress corrosion cracking. As the Zn/Mg ratio is increased fracture energy obtained by slow strain rate test was decreased, which means degradation of SCC resistance. While the fracture energy was increased with Cu contents although it is below 1%, which means improvement of SCC resistance. These effects of composition change on the SCC resistivity were identified by observing the fracture surface and crack propagation.

• 드라이브 ㆍ 컨트롤
• /
• 제13권2호
• /
• pp.10-18
• /
• 2016

A front-end loader (FEL) mounted on an agricultural tractor is one of the most commonly used implements to mechanize routine agricultural tasks. When the FEL is used with a loaded bucket, careful operation is required to maintain safety and avoid spillage when the tractor passes a bump because a change in the gravity center of the tractor due to varied loadings can affect the stability of the tractor. Use of a boom suspension system consisting of accumulators and orifice dampers can be instrumental in reducing pitching vibrations while increasing the handling performance of the FEL-mounted tractor. The objective of this research was to reduce bump shocks by adding an orifice and a flow control valve to the original hydraulic circuit composed solely of accumulators. A simulation study was performed using the SimulationX program to investigate the effects of an accumulator and an orifice-throttle damper on bump shocks. Results showed that the peak pressure on a boom cylinder and the vertical acceleration of a bucket were significantly affected by use of both an accumulator and an orifice damper. In a field test conducted with a 75-kW tractor, the peak pressure of the boom cylinder, and the root mean square (RMS) vertical acceleration of the bucket and seat were reduced by on average, 23.0, 42.2, and 44.9% respectively, as compared to those measured with the original accumulator system, showing that an improved design for the accumulator hydraulic circuit can reduce bump shocks. Further studies are needed to design a tractor suspension system that includes the effects of cabin suspension and tires as well as dynamic analysis.

• 대한기계학회논문집A
• /
• 제38권11호
• /
• pp.1231-1237
• /
• 2014

군용 차량의 경우 야지 주행에 대한 성능 시험이 필수적인데 실차 시험의 경우 비용과 시간에 의한 제약을 받게 되므로, 시뮬레이션을 통한 성능 분석이 효율적이다. 본 연구에서는 상용 다물체 해석프로그램인 MSC.ADAMS 를 이용하여 차량 모델을 개발한다. 타이어 수직 강성 시험을 수행하고 FTire 모델에 반영하여 타이어 모델을 생성한다. 댐퍼의 경우 비선형 특성 시험을 통해 얻은 결과를 반영하여 댐퍼를 모델링 하였으며, 겹판 스프링은 빔 요소 모델로 차량 모델을 구성한다. 단순 장애물 통과 시험 및 파형로 통과 시험을 수행하고 가속도 응답 및 휠 하중 응답 분석을 통해 차량 모델의 신뢰성을 검증하였다.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.347-354
• /
• 2000

This paper presents performance characteristics of a semi-active suspension featuring continuously variable ER (electro-rheological) dampers. These are evaluated through the field test of a passeng er car. Four ER dampers (two for front and two for rear part) are manufactured and their field-dependent damping properties are experimentally investigated. The damping force responses to step input fields are also identified by employing small size of high voltage amplifiers which are made adaptable to the field test. A skyhook controller considering the vertical, pitch and roll motions is formulated and incorporated with a car to be tested. The field test is then undertaken in order to evaluate both comfortability and steering stability showing bump, dive and squat responses.

• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.52-58
• /
• 2011

In this paper, the direct bonding process between FPCB and HPCB was studied. By using an ultrasonic horn which is mounted on the ultrasonic bonding machine, it is alternatively possible to bond the gold pads attached on the FPCB and HPCB at room temperature without an adhesive like ACA or NCA. The process condition for obtaining more bonding strength than 0.6 Kgf, which is commercially required, was carried out as 40 kHz of frequency, 0.6 MPa of bonding pressure and 2 second of bonding time. The peel off test was performed for evaluating bonding strength which results in more than 0.8 Kgf.

• 한국항공우주학회지
• /
• 제33권8호
• /
• pp.8-17
• /
• 2005

저속 압축성 유동에서 사용하는 예조건화 기법은 수렴성 증진에 효과적이다. 본 연구에서는 일반적인 오일러 지배 방정식과 각각 다르게 무차원화한 세 가지 종류의 예조건화 기법을 3차 공간 정확도의 MUSCL, DADI, 다중 격자, 국소 시간 전진 기법을 이용하여 2차원 비점성 bump 유동에 적용하였다. 결과적으로 국소 예조건화 기법에 전역 예조건화 기법의 압력 항 무차원화 방법을 적용하면, 마하수에 무관한 수렴 특성을 얻을 수 있다. 또한, 점근해석을 이용하여 각 예조건화 기법의 특성에 대해 언급하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.709-710
• /
• 2009

• Tribology and Lubricants
• /
• 제32권3호
• /
• pp.75-81
• /
• 2016

Future electronics such as electronic paper and foldable cellphone are required to be flexible and transparent and should have a high performance. In order to fabricate the flexible electronics using flexibility transfer process, techniques for transferring various devices from rigid substrate onto flexible substrate by elastomeric stamp, have been developed. Adhesion between the elastomeric stamp and various devices is crucial for successful transfer process. The adhesion can be controlled by the thickness of the stamp, separation velocity, contact load, and stamp surface treatment. In this study, we fabricated the bump shape stamp consisting of a UV-curable polymer and investigated the effects of curing condition, separation velocity, and contact load on the adhesion characteristics of bumps. The bumps with hemispherical shape were fabricated using a dispensing process, which is one of the ink-jet printing techniques. Curing conditions of the bumps were controlled by the amount of UV irradiation energy. The adhesion characteristics of bumps are evaluated by adhesion test. The results show that the pull-off forces of bumps were increased and decreased as UV irradiation energy increased. For UV irradiation energies of 300 and 500 mJ/cm², the pull-off forces were increased as the separation velocity increased. The pull-off forces also increased with the increase of contact load. In the case of UV irradiation energy above 600 mJ/cm², however, the pull-off forces were not changed. Therefore, we believe that the bump shape stamp can be applied to roll-based transfer process and selective transfer process as an elastomeric stamp.

• 한국지반공학회논문집
• /
• 제33권11호
• /
• pp.35-43
• /
• 2017

본 연구에서는 정착부 표면에 저항체를 설치한 앵커의 인발거동특성을 모형시험을 통해 규명하였다. 모형시험은 원형의 토조 중앙에 앵커체를 설치한 후 앵커를 등속으로 인발하면서 인발저항력을 측정하였다. 본 연구에서는 앵커형식(저항체 설치 유무), 앵커체 표면의 마찰조건($1/3{\phi}$, $2/3{\phi}$, ${\phi}$)과 돌기형 저항체 개수(1set, 2set, 4set), 돌기형 저항체 높이(0.05d, 0.10d, 0.20d) 등 총 10가지의 조건에 대하여 인발시험을 실시하였다. 인발시에는 일정한 속도(1mm/min)를 유지하였으며, 최대 80mm까지 인발하여 각 조건별 인발하중 및 변위를 측정하였다. 인발시험 결과 확장형 앵커는 마찰형 앵커와 비교하여 최대 인발저항력 뿐만 아니라 잔류 인발저항력도 크게 발생하는 것으로 분석되었다. 돌기형 저항체의 설치개수 증가에 따라 최대 인발저항력이 증가하였으며, 잔류 저항력 비율은 171~591%로 마찰형 앵커에 비해 현저하게 증가하였다.

• 한국군사과학기술학회지
• /
• 제1권1호
• /
• pp.65-81
• /
• 1998

Objective technology development has been carried out aiming performance improvement of the stabilized gun-pointing system for Type-4 tank. The full nonlinear simulation programs with gun bending modes and nonlinearities were developed to estimate, analyze and design the driving and stabilization system, and validated through the comparisons between simulations and test results of the existing Type-1 tank. The prototype is designed, fabricated, tested and evaluated on the test range as well as in the laboratory and followed by development and operational tests. The performance test results on stationary and on-the-move conditions are turned out to be superior to those of the advanced tanks developed in foreign countries.