• 전자공학회논문지 IE
• /
• v.48 no.3
• /
• pp.10-15
• /
• 2011

In the case of designing an acoustic transducer for high power application, we usually aim to transfer the source electric energy to the output acoustic energy as large as possible. For this purpose, we should match the impedance of the power amplifier to the impedance combined with the acoustic transducer impedance and the radiation impedance. Especially if we have electrical source with almost zero impedance, we need improve the power factor of the acoustic transducer in the load. In this paper, we propose a broad band impedance matching method by the improvement of power factor, which applies ABCD matrix.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.11
• /
• pp.99-104
• /
• 2003

We are designed and fabricated the Printed dual monopole antenna with CPW feeder for PCS and IMT2000 band. In this paper il proposed modified dual monopole antenna that is transform conventional monopole antenna to get dual band frequency. The dual monopole antennas had broad bandwidth and omni -directional radiation patterns in construct with conventional monopole antenna. On a monopole operated a stub to other monopole antenna, we could obtain easy an impedance matching. It is increased band width of impedance. The antenna bandwidth is about 150MHz(1.74 ∼1.89〔GHz〕)at 1$^{st}$ resonance frequency and 290MHz(1.95∼2.24GHz) at 2$^{nd}$ resonance frequency on VSWR(equation omitted)1.5 and then we can be got not only 1.75∼1.87〔GHz〕 PCS band but also 1.92∼2.17 〔GHz〕).GHz〕).

• Journal of electromagnetic engineering and science
• /
• v.13 no.4
• /
• pp.224-232
• /
• 2013

This paper describes composite cavity-backed crossed scythe-shaped dipoles with wide-beam circularly polarized (CP) radiation for use in Global Navigation Satellite Systems. Each branch of the dipole arm contains a meander line, with the end shaped like a scythe to achieve a significant reduction in the size of the radiator. For dual-band operation, each dipole arm is divided into two branches of different lengths. The dipoles are crossed through a $90^{\circ}$ phase delay line of a vacant-quarter printed ring to achieve CP radiation. The crossed dipoles are incorporated with a cavity-backed reflector to make the CP radiation unidirectional and to improve the CP radiation beamwidth. The proposed antennas have broad impedance matching and 3-dB axial ratio bandwidths, as well as right-hand CP radiation with a wide-beamwidth and high front-to-back ratio.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.7
• /
• pp.664-672
• /
• 2009

In this paper we propose an on-glass antenna which consists of conducting dual center striplines and multi-loaded striplines. Multi-loaded striplines and dual center lines were employed for achieving a broad matching bandwidth and improving a vertical radiation gain, respectively. The detail design parameters were determined using the Pareto genetic algorithm with an full wave EM simulator. The optimized design was built and installed on a commercial vehicle, and the antenna performances such as the return loss and the radiation gain were measured in a semi-anechoic chamber. The measurement results showed the matching bandwidth($S_{11}$<-3 dB) of about 49 % in the T-DMB frequency band, the vertical gain of about -3 dBi along the bore-sight direction, and the average gain of about -10 dBi along the azimuth direction.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.230-239
• /
• 2009

In this paper, we propose a novel on-glass antenna for FM radio reception in a recreation vehicle(RV). We use a multi-loop structure that takes advantage of a broad matching bandwidth and a high vertical radiation gain by efficiently utilizing a given space of a quarter glass in spite of the simple planar structure. Transparency of the antenna is also improved by adjusting the stripline widths based on the induced current distributions. The proposed antenna is printed on a quarter glass of a commercial vehicle and antenna performances such as the return loss and the gain are measured in a semi-anechoic chamber. The result shows the average gain of -9.67 dBi along the bore-sight direction($\theta=90^{\circ}$, $\phi=270^{\circ}$) in the FM radio band(80$\sim$l10 MHz), which is higher than a commercial monopole typed on-glass antenna($G_{ave}$=-12.49 dBi) and micro-antenna($G_{ave}$=-19.24 dBi) mounted on the roof of the RV.

• Journal of the Korea Knowledge Information Technology Society
• /
• v.12 no.4
• /
• pp.539-550
• /
• 2017

In this paper, we designed, fabricated and tested an UHF band cylindrical dipole array antenna. In the proposed antenna, cylindrical dipoles were vertically arranged in four stages. A parallel structure feeding circuit was installed inside the cylindrical dipole and mounted so as to be broadband matching. The feeding circuit was installed at the center of the cylindrical dipole to optimize the gain flatness characteristic of the azimuth direction omnidirectional radiation pattern. Minimizing the difference between the signals branched from the feeding circuit and realizing the symmetry of the radiation pattern. The required specifications are more than 11.2% bandwidth in UHF band, above 6dBi antenna gain, standing wave ratio of 2:1 or less, less than ${\pm}1dB$ gain flatness in azimuth radiation pattern, more than 13 degrees in elevation radiation pattern of 3dB beamwidth. We confirmed the possibility of implementation through M&S and verified the result of M&S through production and testing. The test results are 11.2% bandwidth in the UHF band, 6.30 to 8.31 dBi gain, 1.53:1 standing wave ratio or less, within ${\pm}0.2dB$ gain flatness in the azimuth radiation pattern, elevation radiation pattern of 3dB beam width was 15.62 to 15.84 degrees. The test result meets all requirements specifications.

• Composites Research
• /
• v.21 no.5
• /
• pp.9-14
• /
• 2008

Carbon nanofibers (CNFs) were used as dielectric lossy materials and NiFe particles were used as magnetic lossy materials. Total twelve specimens for the three types such as dielectric, magnetic and mixed radar absorbing materials (RAMs) were fabricated. Their complex permittivities and permeabilities in the range of $2{\sim}18$ GHz were measured using the transmission line technique. The parametric studios for reflection loss characteristics of each specimen to design the single-layered RAMs were performed. The mixed RAMs generally showed the improved absorbing characteristics with thinner matching thickness. One of the mixed RAMs, MD3with the thickness of 2.00 mm had the 10 dB absorbing bandwidth of 4.0 GHz in the X-band ($8.2{\sim}12.4$ GHz). It also showed very broad 10 dB absorbing bandwidth as wide as 6.0 GHz in the Ku-band ($12.0{\sim}18.0$ GHz) with the thickness tuning to 1.49 mm. The experimental results for selected several specimens were in very good agreements with simulation ones in terms of the overall reflection loss characteristics and 10 dB absorbing bandwidth.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.4165-4170
• /
• 2012

In this paper, a method for the improvement in the gain and bandwidth of a microstrip-fed broadband planar quasi-Yagi antenna (QYA) is studied. The broadband characteristics of the QYA are achieved from the coplanar strip-fed planar dipole driver and a parasitic director close to the driver. In order to obtain stable gain variation over the required frequency band, a director and a ground reflector are appended to the driver having a nearby parasitic director. The QYA is fed through an integrated balun composed of a microstrip line and a slot line which are terminated in a short circuit. By adjusting the feeding point, a broadband impedance matching is obtained. A QYA with an operating frequency band of 1.75-2.7 GHz and a gain > 4.5 dBi is designed and fabricated on an FR4 substrate with dielectric constant of 4.4 and thickness of 1.6mm. The experimental results show that the fabricated antenna has good performance such as a broad bandwidth of 59.7%(1.55-2.87 GHz), a stable gain between 4.7-6.5 dBi, and a front-to-back ratio > 10 dB. The measured data agree well with the simulation, which validates this study.