• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.4
• /
• pp.435-442
• /
• 2011

In an attempt to respond to the increase in international oil prices and reduce operating expenses, ship remodeling was carried out on a 740ton class tuna purse seiner. To strengthen the competitiveness of the fisheries industry by improving vessel performance, a bulbous bow was newly equipped. The slipway and rudder area were also lengthened and enlarged with the propeller and main engine remained unchanged. To reduce the hull resistance, a circle type bulbous bow was attached on the hull behind bow thruster and thus the cost for exchanging electrical equipment for bow thruster was reduced. The new rudder area was expanded 15% more than the old one within the extent that the existing mechanical control part and rudder stock were not changed. To prevent fishing net damage and stabilize wake field, slipway was lengthened to the optimal position. All of the new design of remodeling parts went through the model tests in towing tank and CWC. Besides resistance test, all of necessary model test results were delivered for hydrodynamic character for the modified ship. The maneuvering simulation to verify that the remodeled ship satisfies the IMO rules was performed in both zigzag and turning tests. The estimated resistance with new bulbous bow and lengthened stern was reduced by 4.8% in the 2-dimensional analysis and 17.4% in the 3-dimensional analysis in comparison of conventional ship. The average reduction of resistance was estimated about 10%. Maneuvering character of modified hull form was found to satisfy all regulations under IMO. The remodeling of tuna purse seiner can not only improve fishing performance but also contribute to reduction of operating cost by saving energy for the fisheries industry.

• Journal of Fisheries and Marine Sciences Education
• /
• v.19 no.1
• /
• pp.129-136
• /
• 2007

The component parts of the shell plate of a ship are steel. but the screw propeller or the bow thruster is a compound of bronze, nickel and aluminum. On account of the these different components between metals of the shell plate, the screw propeller and the bow thruster, which are underwater, the shell plate of a ship is corroded by the action of ionization. Authors investigated the corrosion loss of the zinc anodes which were attached to the bottom shell of the training ship Kaya for about two years. The obtained results were as follows:1. In case of the shell plate the difference of the corrosion loss according to port and starboard was almost nothing. But the corrosion loss of the forward part was more than that of the aftward part.2. There was little difference in the corrosion loss between the forward and the aftward part on the bilge keel.3. The corrosion loss of the fore, midship and aft part on the false keel were 24.7%, 22.4% and 23.9% respectively.4. The corrosion loss of the fore and the aft part on the false keel was more than that of the midship part.5. The corrosion loss of the bow thruster was greater than any other parts.6. The nearer the zinc anode to the screw propeller the more the corrosion loss on the stern frame, and the situation was also same as on the rudder.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.98-99
• /
• 2016

The aim of study is to develop a dual driven ship berthing/deberthing system with $360^{\circ}$ steerability. A large ship used bow thruster, side thruster and pod propulsor etc. when approaching to a pier. But as marine leisure boats become large-scaled, the number of accidents is recently increasing what caused a ship to crash into a ship and a ship to crash into mooring facilities during berthing/deberthing on a marina. To solve the problem, the control responsiveness of a joystick connected with two motors and a propeller was checked and torque was increased by the electromagnetic design of magnetic gear. A sea trial test was carried out to investigate a performance of the developed system in the real sea.

• Journal of Navigation and Port Research
• /
• v.27 no.2
• /
• pp.193-198
• /
• 2003

The slew motion of a single point moored ship by the external forces is considered to control itself. The maneuvering equations of motion are derived to express the motion of a ship. The wind forces and the wave forces are considered as the external forces of the single point moored ship in the simulation. The wave forces in the time domain analysis are generated from the frequency transfer function calculated by 3-D source distribution method. The wind forces are used the results from OCIMF(1994). To control the slew motion, the bow thruster and the bridle anchoring with 2nd anchor are used in the numerical simulation.

• Journal of Navigation and Port Research
• /
• v.32 no.8
• /
• pp.597-602
• /
• 2008

T.S. HANBADA has a relatively large hull and superstructures above the water line, so she has much of leeway or turning of bow with the effect of winds. Especially on berthing, unberthing and/or sailing on low speed, these effects take place more significant. Therefore, it was carried out the numerical calculation of the wind force and moments acting on the T.S. HANBADA, and then calculated the leeway angle and counter rudder angle with the relative wind direction and velocity. Also, it was suggested the maximum wind velocity which could be berthed or unberthed used by bow thruster and the tugboat operations in strong winds. These results will be great helpful to the vessels with large superstructures on ship's handling in harbour or tugboat operations.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.290-297
• /
• 2004

In this paper, one of the harbour maneuvering tests is described. Its goal is to investigate the so-called crabbing performance of ships. By crabbing is meant the ability of the vessel to move sideways with the use of her own maneuvering devices like propellers, rudders, transverse thruster, etc. the 3m ferry model is made by ocean engineering wide tank in the university of ulsan. when the model ship is leaving and going to the quay, Transverse forces and Yawing moments are measured, in the condition of zero longitudinal force and the design draught, by load cell attached to the longitudinal center of gravity on the ship. the purpose of the experiment is to verify the reliability of ocean wide tank in university of ulsan about crabbing test compared with results of foreign research institute.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.359-362
• /
• 2006

This study develops an automatic berthing control algorithm for ships with a bow thruster and a stern thruster as well as a rudder. A nonlinear mathematical model for low speed maneuvering of ships is used to develop a MIMO(multi-input multi-output) nonlinear control algorithm. The algorithm consists of two parts, which are forward velocity control and heading angle control. The control algorithm is designed based on the longitudinal and yaw dynamic models of ships. The desired heading angle is obtained by the so called "Line of Sight" method. An optimal control force allocation method of the rudder and the thrusters is suggested. The nonlinear control algorithms are tested by numerical simulations using MATLAB, and shows good tracking performances.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.3
• /
• pp.165-174
• /
• 2023

Unmanned Surface Vehicle (USV)'s berthing and unberthing is the most difficult maneuvering tasks and have the highest risk of accidents. In this paper, we designed a berthing/unberthing control algorithm given human joystick command for an USV equipped with a waterjet and a bow thruster. The berthing and unberthing maneuvers are performed remotely by a joystick operator at the Ground Control Center (GCC) where the status of USV and environmental situation can be monitored. We interpret the human joystick commands into USV's desired speed, yaw rate, and heading angle commands. next, we developed a control algorithm for the desired target values of MIMO actuators (engine speed, bucket step, nozzle angle, and bow thruster state) to follow the interpreted commands. The validity of the control algorithm is confirmed through simulations and sea trials at Gwang Am port.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.2
• /
• pp.10-17
• /
• 2010

Conventionally, because it is difficult to control a ship in shallow water and because attempting to do so creates unwanted environmental effects, maneuvering ships in the harbor area for berthing is usually done with the assistance of tugboats. In this paper, we propose a new method for berthing ships automatically by using bow and stern thrusters. Specifically, a steering motion model of a ship is considered, and parameters in the equation are evaluated by the system identification technique. An optimal controller based on observations was designed from the linearization of the non-linear ship motion in the horizontal plane. It is used to reduce the uncertainty about the ship's dynamics and reduce measurement requirements. The performance of the controller was also analyzed for its robustness relative to avoiding disturbing the environment due to winds, currents, and wave-drift forces. Experiments were conducted to estimate the potential for identifying result and the design of the controller. Specifically, in this paper, the system modeling and tracking control approach are discussed based on a two-degree-of-freedom (2DOF) servo-system design.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2008.09a
• /
• pp.62-67
• /
• 2008

The hovercraft is the amphibious hovercraft. Design and manufacturing companies of the aero propeller exist rarely in the world. Hence the propeller has beef designed and manufactured by manufacturing companies which make aero propeller mainly. In this paper, the hovercraft propeller of similar, which is building and designing by HHIC, is considered the type of aero propeller, rotational speed, diameter, number of blades, Open air propeller efficiency. As the result of check, hovercraft which is necessary huge static thrust is needed the ducted propeller in order to improve climbing capacity. However, the number of blades and turning direction almost do not affect.