• Journal of Marine Bioscience and Biotechnology
• /
• v.7 no.1
• /
• pp.1-10
• /
• 2015

Bio diesel has advantages to reduce GHG(Greenhouse Gas) compare with the fossil fuel by using oil comes from plant/animal sources and even waste such as used cook oil. The diversity of energy feeds brings the positive effects to secure the national energy mix. In this circumstance, micro-algae is one of the prospective source, though some technical barriers. We analyzed the bio diesel which was derived from Dunaliella tertiolecta LB999 through the BD100 quality specifications designated by the law. From that result, it is revealed that the oxidation stability is one of the properties to be improved. In order to find the reason for low oxidation stability, we analyzed the oxidation tendency of each FAME components through some methods(EN 14111, EN14112, EN16091). In this study, we could find the higher double bond FAME portion, the more oxidative property(C18:1${\ll}C18:3$) in bio diesel and main unsaturated FAME group is acted as the key component deciding the bio diesel's oxidation stability. It is proved experimentally that C18:3 FAME are oxidized easily under the modified accelerated oxidation test. We also figure out low molecular weight hydrocarbon and FAME were founded as a result of thermal degradation. Some alcohol and aldehydes were also made by FAME oxidation. In conclusion, it is necessary to find the way to improve the micro-algal bio diesel's oxidation stability.

• Culinary science and hospitality research
• /
• v.17 no.4
• /
• pp.316-325
• /
• 2011

The property of deep frying oil is one of die important factors in fried food quality. The purpose of this study is to identify die quality of deep frying oil in continuous usages for 4 days by two types of fryers: traditional and modified fryers. After frying polk cutlets, die flying oil was kept not only for several physical analyses such as color, viscosity, and water content but also for quality analyses of flying oil such as free fatty acid, double bond changes and oxidative rancidity formation. The fried oil by a traditional flyer was significantly increased in die physical values of color and viscosity than that by a modified fryer. In die acid value, the fried oil by a traditional fryer was significantly increased in free fatty acid than that by a modified fryer while die iodine value was significantly decreased in die fried oil by a traditional fryer when compared to control oil and fried oil by a modified fryer. In die peroxide value as an indicator of primary oxidation products, die fried oil by both fryers was significantly increased till die second day but decreased in die value after die third day because of unstable hydroperoxides' decomposition. In die p-anicidine value as an indicator of secondary oxidation products, die fried oil in a traditional fryer was significantly increased in die value than that in a modified fry.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.409-409
• /
• 2014

Recently hexagonal boron nitride (h-BN), III-V compound of boron and nitrogen with strong covalent $sp^2$ bond, is a 2 dimensional insulating material with a large direct band gap up to 6 eV. Its outstanding properties such as strong mechanical strength, high thermal conductivity, and chemical stability have been reported to be similar or superior to graphene. Because of these excellent properties, h-BN can potentially be used for variety of applications such as dielectric layer, deep UV optoelectronic device, and protective transparent substrate. Ultra flat and charge impurity-free surface of h-BN is also an ideal substrate to maintain electrical properties of 2 dimensional materials such as graphene. To synthesize a single or a few layered h-BN, chemical vapor deposition method (CVD) has been widely used by using an ammonia borane as a precursor. Ammonia borane decomposes into hydrogen (gas), monomeric aminoborane (solid), and borazine (gas) that is used for growing h-BN layer. However, very active monomeric aminoborane forms polymeric aminoborane nanoparticles that are white non-crystalline BN nanoparticles of 50~100 nm in diameter. The presence of these BN nanoparticles following the synthesis has been hampering the implementation of h-BN to various applications. Therefore, it is quite important to grow a clean and high quality h-BN layer free of BN particles without having to introduce complicated process steps. We have demonstrated a synthesis of a high quality h-BN monolayer free of BN nanoparticles in wafer-scale size of $7{\times}7cm^2$ by using CVD method incorporating a simple filter system. The measured results have shown that the filter can effectively remove BN nanoparticles by restricting them from reaching to Cu substrate. Layer thickness of about 0.48 nm measured by AFM, a Raman shift of $1,371{\sim}1,372cm^{-1}$ measured by micro Raman spectroscopy along with optical band gap of 6.06 eV estimated from UV-Vis Spectrophotometer confirm the formation of monolayer h-BN. Quantitative XPS analysis for the ratio of boron and nitrogen and CS-corrected HRTEM image of atomic resolution hexagonal lattices indicate a high quality stoichiometric h-BN. The method presented here provides a promising technique for the synthesis of high quality monolayer h-BN free of BN nanoparticles.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.5
• /
• pp.196-201
• /
• 2014

We investigated defects and surface polarity in AlN and GaN by using wet chemical etching. Therefore, the effectiveness and reliability of estimating the single crystals by defect selective etching in NaOH/KOH eutectic alloy have been successfully demonstrated. High-quality AlN and GaN single crystals were etched in molten NaOH/KOH eutectic alloy. The etching characteristics and surface morphologies were carried out by scanning electron microscope (SEM) and atomic force microscope (AFM). The etch rates of AlN and GaN surface were calculated by etching depth as a function of etching time. As a result, two-types of etch pits with different sizes were revealed on AlN and GaN surface, respectively. Etching produced hexagonal pits on the metal-face (Al, Ga) (0001) plane, while hexagonal hillocks formed on the N-face. On etching rate calibration, it was found that N-face had approximately 109 and 15 times higher etch rate than the metal-face of AlN and GaN, respectively. The size of etch pits increased with an increase of the etching time and they tend to merge together with a neighbouring etch pits. Also, the chemical mechanism of each etching process was discussed. It was found that hydroxide ion ($OH^-$) and the dangling bond of nitrogen play an important role in the selective etching of the metal-face and N-face.

• Culinary science and hospitality research
• /
• v.18 no.2
• /
• pp.1-18
• /
• 2012

This study was conducted to find out the effect of the role of a mentor on work outcomes and job satisfaction among the cooks working at five star hotels in Busan and Ulsan areas. 192 samples were obtained and analyzed using a social science statistics program SPSS/PC + for Window 12.0 along with frequency analysis, factor analysis, reliability analysis and regression analysis. The results of the analyses are as follows. First, experience and skills helped develop a bond of sympathy and cooperative relationships between a mentor and a mentee enabling them to achieve the organization's goal and provide high quality services. Second, the work execution and protective function of a mentor can create active planning and acting by helping individuals to improve for the future and giving them opportunities for professional works. Third, the psychological and social function of a mentor can create a bond of sympathy through personal contact, maintain smooth relationships in an organization and affect satisfaction in the working environment. Therefore, a mentor can have positive effects on work outcomes and satisfaction among cooks and also improve them. In this respect, through various efforts to institutionalize and activate the current nonofficial mentoring system into an official one, it should be used as a way of improving business performance and competitiveness.

• Journal of dental hygiene science
• /
• v.9 no.4
• /
• pp.405-412
• /
• 2009

The purpose of this study investigated the effect of Au coating on adhesion between porcelain matrix and metal substructure interface. Titanium, Ni-Cr alloy and Co-Cr alloy are well known as proper metal for the dental restorations. The success of a porcelain fused to metal (PFM) restoration depends upon the quality of the porcelain-metal bond. However, adhesion between dental alloys and porcelain is related to diffusion of oxygen during ceramic firing. The excessive oxidized layers make hard adhesion between dental alloy and ceramic. Ni-Cr and Co-Cr specimens were divided into test and a control group and Titanium specimens were divided into three test groups and a control group. Each group had 20 specimens. The adhesion characteristics of porcelain and metal with Au coating layer and without Au coating layer were observed with scanning electron microscopy(SEM). The adhesion was evaluated by a biaxial flexure test and volume fraction of adherent porcelain was determined by SEM/EDS analysis. Result of this study suggest that Au coating layer is effective barrier to diffuse oxide layer completely protect non-precious alloys from oxidation during the porcelain firing. The SEM photomicrographs of cross-section specimens showed a smooth interface between Au coating layer and metals and porcelain which suggested proper chemical bonding, and no gap, porosity were observed. The mode of failure was mainly adhesive for Ti tested specimens, but mixed failures with adhesive and cohesive were observed in Ni-Cr and Co-Cr specimens. The adhesion between non-precious metals and porcelain would not be improved by Au coating agent. However, It is suggested that the continuous study is required further investigation and development.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.6A
• /
• pp.525-534
• /
• 2010

A road curbstone is a structure installed at the boundary of the sidewalk and the street with the objectives of road drainage, drawing attention and such. The current general construction method of curbstones places foundation concrete for the curbstones first, waits until the concrete reaches the strength to support the curbstones, places the curbstones on top, and then places the gutter and rear filling concrete. Such method has the issues of poor compaction and weakened bond strength of concrete due to split placing of concrete, and causes the curbstones to easily separate due to vehicle impact or earth pressure, in turn creating maintenance costs and spoiling the aesthetics. To improve such conventional construction methods, an all-in-one method was developed using formwork rail and jig where both the curbstones and gutter can be worked at the same time, and to evaluate the structural performance, static tests of lateral loading test, pullout test, and bending test were executed, and dynamic tests such as pendulum test and actual vehicle impact test were executed. In all tests, the all-in-one construction method using formwork rail and jig was shown to be superior to the conventional construction method by the increase of construction quality and bond strength of concrete.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.13-22
• /
• 2007

This study was carried out to scrutinize possibility of manufacturing pitch pine (Pinus rigida) glued laminated timber in order to add values of pitch pine trees. Also, it was investigated to improve bending performance of pitch pine glulam. Pitch pine was imported as one of major plantation species in Korean peninsula. Machine stress rated grades of pitch pine lumber mostly ranged between E7 and E9. which grades were more or less inferior to producing high quality glulam. However, the adhesive properties between pitch pine and pitch pine, and between pitch pine and Japanese larch (Larix kaempferi Carr.), such as shear bond strength, wood failure rate and de-lamination rate of bonded layer submerged in cold and boiling water, were higher than Korean Standard criteria. These properties are essential for manufacturing glulam with single species or multiple species. The modulus of rupture (MOR) of pitch pine glulam exceeded the criterion of Korean Standard for glulam strength grade but modulus of elasticity (MOE) was lower than the criterion. On the other hand, the bending performances (MOR and MOE) were improved 20 percent by mixing with Japanese larch laminar. It is effective to arrange higher quality Japanese larch laminar at the outer layer of glulam for improving bending performances. In conclusion, it is possible to use low quality pitch pine as laminar of structural glulam for adding values of pitch pine.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.42 no.6
• /
• pp.39-49
• /
• 2014

Unpleasant facilities have been unwelcomed by residents within the region since they are considered to negatively influence the living conditions of the region. Yet recently, a park project within these unpleasant facility areas has begun to improve the negative impression of the region and the satisfaction of local residents has been shown to be very high. Also a park project within unpleasant facilities is found to have significant influence on the community, including resolving conflicts and building mutual friendships among residents by creating pleasant living conditions and improving the quality of life of local residents. The purpose of this study is to investigate how the park project within unpleasant facilities changes the satisfaction level of local residents and affects the sense of community. In order to do so, surveys were given to visitors of Seoul Maru Park, which was turned into a park from a sewage treatment center. According to the analysis result, after the sewage treatment center was recreated as Maru Park, citizen satisfaction was found to be very high. The sense of community that the visitors feel was found to be high in general, but the 'sense of connection and neighbor bonds' turned out to be lower compared to the 'sense of settlement and belonging.' A regression analysis was performed to determine the relative influence of visitor satisfaction on the sense of community. As a result, in the division of 'sense of settlement and belonging,' the satisfaction with ecological health was affected the most, followed by satisfaction with scenic beauty, whereas satisfaction with cleanness had no influence. In the division of 'sense of connection and neighbor bond,' none of the satisfaction with cleanness, ecological health and scenic beauty showed any influence in the analysis. According to the above result, a park project within unpleasant facilities brings a positive influence on the 'sense of settlement and belonging,' yet in order to improve the 'sense of connection and neighbor bond,' which is not influenced by the project, the adequate facilities and activity programs are considered to be necessary to change the residents' of sense of community.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.3 s.17
• /
• pp.75-82
• /
• 2005

Sewage facilities are positively necessary for environment improvement such as rainwater removal, sewage disposal, preservation of the quality of water and health of the citizens in present-day. Meanwhile, a deterioration of the concrete sewer pipe is increasing rapidly due to the chemical and physical attack and especially biochemical attack that is to say biodeterioration. So, in advanced countries, prediction techniques and corrosion inhibition system for sewer concrete are developed and are being applied. Also, antibiotics were developed already but application of that is low because it is not economical and has no practical use. But, in domestic, countermeasures for the corrosion of sewage concrete are not sufficient and biochemical attack is not reflected in those essentially. In this study, to prevent biochemical corrosion of the sewer concrete, surface of the concrete was spread with liquefied inorganic antibiotics and then its engineering properties were experimentally investigated. As a result, compressive strength of the specimen spread with antibiotics were similar to those of non spread, Both bond strength and abrasion amount of the specimen spread with antibiotics were inferior to non spread. Properties of absorption and air permeability of the specimen spread with antibiotics were superior to non spread. Finally, carbonation depth, chloride ion penetration depth and weight change ration of the specimen spread with antibiotics were smaller than non spread.