• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.34 no.3
• /
• pp.283-286
• /
• 1998

For the systematic study on the resistance characteristics of the planing hull, the experimental studies on the correlation between geometrical characteristics of the subject hull forms and their hydrodynamic characteristics are carried out. This study is the first stage to develop the advanced planing hull type fishing boat and involves the followings; -Resistance characteristics for typical four different section types, -Resistance characteristics for different length-beam ratio

• Journal of Ship and Ocean Technology
• /
• v.9 no.2
• /
• pp.1-10
• /
• 2005

A light-weight cantilever type towing carriage was devised and installed in the towing tank at Seoul National University. Wireless measurement devices were also provided for appropriate data acquisition during high-speed towing tests. With the new carriage system, a series of model tests were performed to investigate the hydrodynamic characteristics of the racing boat in the towing tank and the resistance test results had sufficient accuracy so that they could be used in the development of a high speed planning hull.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.3
• /
• pp.95-99
• /
• 1997

In these days, the pollution of marine environment near island at Korean coastal zone caused by the trash human waste and livestocks excreata become intensified. One of the most economic and efficient way to prevent this pollution problem is to set up island circulating incineration system. In this paper, the result of feasibility study on the application of turtle boat hull form to the incinerating vessel has been summarized especially for the resistance and course keeping point of view.

• Journal of Ship and Ocean Technology
• /
• v.10 no.1
• /
• pp.1-9
• /
• 2006

The resistance reduction by an air lubrication effect of a large air cavity covering the hull bottom surface and the similarity relations involved have been investigated with a series of towing tank tests of three geometrically similar models. The test results of geometrically similar models have indicated that a large air cavity was formed beneath the bottom having a backward-facing step by artificially supplying air is effective for resistance reduction. The areas of air cavity and the required flow rates of air are directly related to the effective wetted surface area. The traditional extrapolation methods seem to be applicable to the estimation of the resistance in the tested range if corrections are made to account the changes in the frictional resistance caused by the changes in the effective wetted surface area. To investigate the effectiveness of air lubrication in improving the resistance performance of a practical ship, a small test boat having a backward-facing step under its bottom has been manufactured and speed trials in a river have been performed. Air has been supplied artificially into the downstream region of the bottom step to form a large air cavity covering the bottom surface. The results have confirmed the practical applicability of air lubrication for the resistance reduction of a small high-speed boat.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.6
• /
• pp.810-817
• /
• 2018

In Korea, tuna purse seine fishery is the industry with the highest production volume in domestic deep-sea fishery. Research has been continuously carried out since the late 1980s, and research on modernization of technology has been actively conducted. However, while auxiliary works boats on the fishing vessels play an important role in the purse seine fishing, related research is not sufficient. In this study, we tried to rebuild the propulsion system of the Net-boat from the propeller to the waterjet type and to perform the hull form conversion to improve the resistance performance of the hull part and improve the motion performance. For this, we calculated the change of the fluid performance of the ship through computational numerical analysis. In addition, towing tank tests were carried out to verify the performance of the existing ship and the ship which changed the propulsion system. As a result, resistance performance of the waterjet type compared to the propeller type was improved by approximately 45 %. It was confirmed that this was due to reduction of the wetted surface area by removing net and improvements in hull form.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.30 no.3
• /
• pp.95-102
• /
• 2018

As a recent technical approach, a high-speed planing hull was tried to realize a friction reducing system by simultaneously actuating the triple streamlined step hull form in association with optimum speed of 35 knot planing for fishing boat. In this approach, the streamlined step hull form with triple structure of type was attached under the bottom of high-speed planing hull, while a friction resistance is reduced in the process of running at the speed of 35 knot. In addition, this research was to make a performance test as to the manufactured product and acquire the purposed values and the development items. Actually, after manufacturing the desired prototype of high-speed planing hull, the significant items, fuel efficiency (second) and amount of fuel consumption (degree) including maximum speed (knot) were estimated for a performance test. And tensile strength (MPa) and bend strength (MPa) as to the completed prototype like a high speed planing hull were also acquired during the test.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.4
• /
• pp.240-247
• /
• 2013

Hydrodynamic characteristics of a planing craft are very sensitive to the hull form variations, especially when the craft navigates with high-speed. Therefore, we need to verify hydrodynamic performances of the craft during the process of hull form design. In this paper, motion performances of a 40ft class cruise leisure boat are evaluated by both model tests and theoretical analyses using two different methods. Model tests are carried out at calm sea and regular wave conditions using high speed towing carriage installed in SNU towing tank. Theoretical methods used are a empirical method proposed by Martin (1976) and a potential method based on Rankine panel (DNV, 2010). The results from the theoretical methods are compared with and verified by those of model tests. Results of empirical formula showed somewhat larger motion RAOs and resonant frequencies than those of model tests. Potential based method showed even larger discrepancies with the model test results. From the analyses of comparison results, we could confirm the limitation of each theoretical method and suggest the way of improvement for the better prediction of motion performances.

• Journal of Navigation and Port Research
• /
• v.34 no.8
• /
• pp.623-628
• /
• 2010

High speed marine vehicle, such as semi-planing, planing craft have been developed recently. These ships paid attention to the resistance characteristics, especially in high speed region. Model test method is divided to two equipment greatly, first 'Towing tank', second 'C.W.C.'. It is difficult to estimate a resistance characteristics for high speed boat. because these are made for low speed ship. This paper suggests a new model test method and system. This is real sea model test and it's comprised of eight part. Firstly, This method is tested at C.W.C that is possible to using in real sea model tes using low speed boat modelt. And then, Real sea model test and CFD calculation are performed and compared with tow way used high speed boat model. It can be a good way to estimate a performance for high speed boat.

• Journal of Korea Ship Safrty Technology Authority
• /
• s.22
• /
• pp.34-53
• /
• 2007

In the case of hull material. large sized merchant ships are made of steel, on the other hand FRP or wood are used for small sized fishing boats. At present in Korea approximately 88,500 fishing boats are in operation of which 70% are made of FRP In the meantime, stainless steel is frequently used as shaft materials of the small-size FRP fishing boat. Namely, the kinds of shaft materials are STS 304(18Cr-8Ni), STS 316(18Cr-12Ni-2.5Mo steel) and STS 630(17Cr-Ni-Nb steel)etc. Among these things, STS 304 which is the cheapest and having ordinary corrosion resistance is most widely used as 2nd class shaft material. But, using STS 304 for shaft system material of the small-size FRP fishing boat on seawater environments entails a severe corrosion which causes shaft system troubles. Particularly, the corrosions tend to be concentrated of the stern and bow side, propeller shaft surface of inside of stern tube and the boat having no stern cooling pipe line system. As a solution for those problems, research on the ways to mitigate corrosion on the part of 2nd class stainless steel shaft have been undertaken. In the result, not only clarification for the reason of corrosion of the part of stainless steel shaft used mainly for the small-size FRP fishing boat was done, but also most optimal corrosion protection system was developed by experimenting shaft's protection simulation based of the electrochemical cathodic protection principle. In addition, verification through the field test on the optimal cathodic corrosion protection method by means of aluminum sacrificial anode was carried out. In this study, effective and economical shaft's protection system is suggested to the small-size FRP fishing boat operator by substantiating the results obtained from the research on the optimal cathodic protection.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.4 no.4
• /
• pp.488-503
• /
• 2012

The stern boat deployment system was investigated to evaluate the capability of launching and recovering rigid hull inflatable boat (RHIB) via the stern ramp. The main parameters to launch and recover RHIB were tested at the design stage. The combined hydrodynamic effect of the stern wake and the water jet flow made it difficult to maintain the maneuvering and sea-keeping ability of RHIB approaching to the stern ramp. The safe recovery course was proposed to maintain the directional control of RHIB and to reduce the combined hydrodynamic effect in the transom zone. To evaluate the feasibility of RHIB recovery, the stern sill depth was measured in various conditions and the ramp availability time was obtained. Also, the experimental percent time operability (PTO) test was performed by the number of successive launching and recovering operations.