• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.99-103
• /
• 2000

This paper describes the development of standard series for turbo blowers. In mass production system, it is very required to standardize blowers to improve the productivity of ordering, estimating, manufacturing. To standardize blowers, we performed researches on the effects of $b_1$(impeller inlet width), $b_2$(impeller outlet width), ${\beta}_1$(blade inlet angle), ${\beta}_2$(blade outlet angle), Z(number of blades) of impellers and geometry of casing experimentally. Through this study, we chose the several best model of turbo blowers with high efficiency and low noise, which represent each specific speed series 63, 80, 100, 125, 160, 200, 250, 315. After the development of such standardized blowers, the test results are used to prepare the fan geometry and performance database for a selection software.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.4
• /
• pp.40-46
• /
• 2014

This paper describes blower performance characteristics of a automated vacuum waste collection system. Blowers serially connected to six or seven centrifugal blowers are evaluated by experimental measurements to understand blower performances according to blower numbers operated. Two different blowers and duct diameters connected to the main blowers are considered. Data acquisition system is introduced to measure pressure and pressure difference at the main duct simultaneously, which is connected to several blowers serially. A auxiliary blower, which is installed between a filter room and an air deodorizing apparatus, is also added to simulate its performance effect on the main blower. Throughout the experimental measurements of the blower system, it is found that pressure and inlet velocity at the upstream of a blower increase 3.7 and 2.4 times separately by increasing the operating blower numbers from one to seven. It is noted that blower efficiency and pressure measured at the system vary according to the distance between a air intake and a blower system. Auxiliary blower is effective to increase blower inlet suction pressure, while total energy consumption is increased relatively.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.309-314
• /
• 2003

High-efficiency turboblowers in the next generation have been successfully developed and commercialized first in the world, using the high-speed BLDC motors and the foil air bearings. About 20-35% savings in electricity consumption in the field are found in comparison with the conventional roots rotary blowers and the integral gear-driven turboblowers. Current TB75 and TB150 products are replacing the existing blowers in the worldwide market.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.177-182
• /
• 2002

In the paper, the development of high-speed industrial turbo blowers with foil air bearings is presented as a first successful commercialization in the world. Their target market is various from wastewater treatment to cement factory processes which require compressed air ranging between 0.6 and 0.8 bar gauge. Employing the state-of·the-art technology of the high-speed BLDC motors, the bump-type foil air bearings and the high- efficient turbo impellers/diffusers, so much compact, efficient and silent blower machines of a single stage are now available in the market, aiming to replace the existing inefficient, bulky and noisy ones, such as roots blowers. The first production lines are established fur 25,75 and 150 hp class blowers. Rotational speeds from about 20,000 to 80,000 rpm are realized directly from the high-speed BLDC motors without any gear boxes, and no lubrication oil is required. A brief introduction of design, manufacture and test results is presented fur mechanical, electrical and aerodynamic performance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1115-1116
• /
• 2010

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.541-543
• /
• 2004

An optimal soot blowing system has been developed for an optimal operation of power utility boilers by both minimization of the use of steam and the number of soot blowers worked during soot blowing. Traditionally, the soot blowing system has been operated manually by operators. However, it causes the reduction of power and thermal performance degradation because all soot blowers installed in the plant should be worked simultaneously even there are lots of tubes those are not contaminated by slagging or fouling. Heat transfer area is divided into four groups, furnace, convection area including superheater, reheater and economizer, and air preheater in the present study. The condition of cleanness of the tubes is calculated by several parameters obtained by sensors. Then, a part of soot blowers works automatically where boiler tubes are contaminated. This system has been applied in a practical power plant. Therefore, comparison has been done between this system and manual operation and the results are discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.91-91
• /
• 2011

This paper describes development procedure of the four types of fuel cell's blowers: pressurized fuel blower, selective oxidation air blower, cathode air blower, and burner air blower. Diaphragm blowers having two heads are selected to maintain force balance when the rotating arms are moving by the driving motor. Dimensions of a diaphragm cavity is designed according to the optimal design procedure using numerical simulation and experimental measurement. Experimental apparatus is designed by considering the bower characteristics having low flow rate and high pressure. Test blower is operated by a diaphragm, which has suction and discharge port on the top of the blower. For analyzing the internal flow of the blower, three-dimensional Navier-Stokes analysis is introduced in the present study. Throughout the optimal design of the blowers, blower performance is enhanced by reducing the unbalance motion of the rotating arm and loss region in the diaphragm cavity.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.189-199
• /
• 1999

The revision was proposed for methods A-weighted sound pressure measurement for fans, blowers and compressors in order to apply newly developed measurement techniques to KS B 6361 established in 1987. This proposal includes modification of terminologies, revision of sound power methods for radiated sound from the body, inclusion of In-duct measurement method, and correction method for flow noise upon microphon.

• The Journal of the Korea Contents Association
• /
• v.17 no.9
• /
• pp.563-574
• /
• 2017

The predominant concerns of the study consist of: (1) the direct effects of social work students' evaluation toward connivers of exam-cheating on their evaluation toward connivers of corruptio ns in social welfare organizations; (2) the dual mediation effects of their concerning dysfunction of whistle-blowing and needing of protection arrangement for whistle-blowers. The notable findi ngs are as follows: First, the evaluation toward a person conniving at exam-cheating significantl y has an effect on the evaluation toward connivers committing corruptions in social welfare orga nizations($.211^{***}$). Second, the more positive evaluation for connivers of exam-cheating, the more concerning dysfunction of whistle-blowing, the less needing protection arrangement for whistle-blowers($-.191^{^{\prime}***}$). The students, concerning dysfunction of whistle-blowing more, show less neg ative evaluation toward a person, conniving at corruption in social welfare organizations($.245^{***}$). The more needing protection arrangement for whistle-blowers, the less positive evaluation regar ding whistle-blowers in the organizations($-.122^{***}$). Lastly, both mediating effects of the needing protection arrangement for whistle-blowers and concerning about dysfunction of whistle-blowing are significant so dual mediator are proved. Some practical implications are discussed based on the study's findings.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.424-432
• /
• 2000

The revision was provided for the method of A-weighted sound pressure measurement for fans and blowers, in which the newly developed measurement techniques were applied to KS B 6361. This revision includes the sound power methods for radiated sound from the body, the in-duct measurement method, and the correction method for flow noise upon measuring microphone, etc.