• The Journal of Engineering Geology
• /
• v.31 no.1
• /
• pp.67-81
• /
• 2021

Grouting is used for reinforcement and waterproofing of soft ground to increase its bearing capacity, reduce the impacts of rising or lowering groundwater levels, and reduce subsidence due to vibration and general causes. This study investigated the enhancement of grout strength and hardening time by the addition of reinforcing fibers, and the development of non-cement grouting materials from blast furnace slag. An experiment was performed to measure the increase in grout strength resulting from the addition of 0.5% increments of aramid and carbon reinforcing fibers. The results show that the uniaxial compressive strength of grout increases with increasing content of reinforcing fiber. Comparison of three admixtures of finely powdered blast furnace slag and 10%, 20%, and 30% calcium hydroxide stimulating agent showed that the uniaxial compressive strength of the mixture increases with increasing content of alkaline stimulant; however, the strength was lower than for 100% pure cement. The reaction of calcium hydroxide with blast furnace slag powder, which increases the strength of the grout, is more effective if injected as a solution rather than a powder.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.415-420
• /
• 2002

This study is intended to investigate the influence of mineral admixtures on the autogenous and drying shrinkage of high performance concrete. According to results, drying shrinkage increases with increase of fly ash content, and it does not show difference with replacement of blast furnace slag powder. It increases when incorporating silica fume or fly ash and silica fume together. The autogenous shrinkage shows increasing tendency with increase of silica fume and blast furnace slag powder content, and incorporating of silica fume or fly ash and silica fume together has effects on reducing autogenous shrinkage. Therefore, it is considered that application of both silica fume and fly ash can reduce the cracks caused by autogenous shrinkage, including enhancement in strength and placeability of high performance concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.823-828
• /
• 1999

Blast furnace slag cement(BSC) has many merits in relation to its prodution cost or environmental problem of these days, but it has still some limitation in broad use mainly because it has the lower early hydration strength than the normal portland cement(PC) has. In the present study, several different experimental concepts to improve its low strength in the early hydration stage were tried out which addition of the effective alkali activators such as Ca(OH)2 and limestone powder, fly ash in existing BSC. It was found that the addition of suitable quantity the effective alkali activators such as Ca(OH)2 and limestone powder, fly ash in BSC can be a possible way to get enough early strength compared with the PC and existing BSC.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.297-300
• /
• 1999

This study was carried out to present the properties of fresh concrete made with ground granulated blast-furnace slag (BFS) powder with variations of blaine and content, and to estimate the utilization of the BFS concrete as admixtural materials for concrete structures of the building. According to the results, the fluidity of concrete which BFS dosage rate was 45% had the considerable difference from that of concrete which BFS dosage rate was not bigger than 35%. Also, the diminution of bleeding was appeared with the increase of blaine and content of BFS. It is concluded that BFS concrete of low blaine can be used effectively in concrete structures of the building.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2002.10a
• /
• pp.149-152
• /
• 2002

This study is performed to evaluate the properties of ECO-permeable polymer concrete with blast furnace slag powder and stone dust. The unit weight is in the range of $1,821kg/m^3{\sim}1,955kg/m^3$, the unit weights of those concrete are decreased $15%{\sim}20.8%$ than that of the normal cement concrete. The highest strength is achieved by ECO-permeable polymer concrete filled blast furnace slag powder 50% and stone dust 50%, it is increased 36% by compressive strength, 119% by tensile strength and 217% by bending strength than that of the normal cement concrete, respectively. The coefficient of permeability is in the range of $5.6{\times}10^{-2}cm/s{\sim}8.1{\times}10^{-2}cm/s$, and it is largely dependent upon the mix design.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.259-262
• /
• 2012

Recently, as the national policy of green growth is promoted, construction field also makes an effort to reduce CO₂ gas released when producing cement continuously. In other words, as the method solving environmental pollution and resources exhaustion, lots of mineral material compounds such as blast furnace slag powder which is industrial by-product, fly ash, red mud, etc. are examined to bo used as the substitute good of cement Therefore this study is to investigate the hardening characteristics of alumino-silicate inorganic binder using red-mud used as a accelerator of industrial by-product such as fly ash and blast furnace slag powder according to curing temperature. As a result, it is effective to use red-mud as the accelerator of inorganic binder with other additory accelerators.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.04a
• /
• pp.147-150
• /
• 2007

As recent buildings often use low-quality concrete materials, are constructed defectively, and are put in extreme environmental conditions, many of them show the shortening of life resulting from the corrosion of reinforcing rods by salt damage, carbonization, freezing and thawing, cracking. This in turn raises the cost of repair and maintenance, so it is required to extend the life of structures through enhancing the durability of concrete. In response to the demand, researches on high-durability concrete are being made actively focused on the maximum water-cement ratio, the maximum unit quantity, the minimum cover thickness, the addition of mineral admixtures, etc. With this background, the present study examined the basic physical properties of concrete containing admixtures for enhancing the durability of concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.218-219
• /
• 2018

This study analyzed the unit weight and compressive strength properties of lightweight concrete using high volume blast furnace slag powder by the mixing ratio of lightweight coarse aggregate to investigate the properties of lightweight concrete using domestic artificial lightweight aggregate.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.939-944
• /
• 2000

This study examines both strength development and pore volume of high temperature curing mortar, using a blast-furnace slag powder (BFS). This study experiments with various pre-steaming period, differing curing temperature and the replacement of BFS. According to the results, the strength development of BFS mortar is stronger when higher curing temperature are used(as opposed to standard curing). Also, regardless of the curing method, pore volume decreases as the curing time increases. From these results we can identify the optimum conditions required pre-steaming period, differing curing temperature and the replacement to produce BFS mortar properties.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.136-137
• /
• 2020

This study compared and analyzed the fluidity and strength characteristics of mortar using the recycling water, indicates strong alkali properties, as pre-wetting water of artificial light aggregate to increase usage ratio of recycling.