• Industrial Engineering and Management Systems
• /
• 제14권2호
• /
• pp.210-219
• /
• 2015

A classification task requires an exponentially growing amount of computation time and number of observations as the variable dimensionality increases. Thus, reducing the dimensionality of the data is essential when the number of observations is limited. Often, dimensionality reduction or feature selection leads to better classification performance than using the whole number of features. In this paper, we study the possibility of utilizing the Markov blanket discovery algorithm as a new feature selection method. The Markov blanket of a target variable is the minimal variable set for explaining the target variable on the basis of conditional independence of all the variables to be connected in a Bayesian network. We apply several Markov blanket discovery algorithms to some high-dimensional categorical and continuous data sets, and compare their classification performance with other feature selection methods using well-known classifiers.

• Transactions on Electrical and Electronic Materials
• /
• 제2권3호
• /
• pp.24-27
• /
• 2001

The end point of oxide chemical mechanical polishing (CMP) have determined by polishing time calculated from removal rate and target thickness of oxide. This study is about control of oxide removal amounts on the shallow trench isolation (STI) patterned wafers using removal rate and thickness of blanket (non-patterned) wafers. At first, it was investigated the removal properties of PETEOS blanket wafers, and then it was compared with the removal properties and the planarization (step height) as a function of polishing time of the specific STI patterned wafers. We found that there is a relationship between the oxide removal amounts of blanket and patterned wafers. We analyzed this relationship, and the post CMP thickness of patterned wafers could be controlled by removal rate and removal target thickness of blanket wafers. As the result of correlation analysis, we confirmed that there was the strong correlation between patterned and blanket wafer (correlation factor: 0.7109). So, we could confirm the repeatability as applying for STI CMP process from the obtained linear formula. As the result of repeatability test, the differences of calculated polishing time and actual polishing time was about 3.48 seconds. If this time is converted into the thickness, then it is from 104 $\AA$ to 167 $\AA$. It is possible to be ignored because process margin is about 1800 $\AA$.

• Child Health Nursing Research
• /
• 제18권4호
• /
• pp.164-169
• /
• 2012

Purpose: The purpose of this study was to compare the effectiveness for infants of antifebrile therapy using a hypothermia blanket or rectal antipyretics following open heart surgery. Methods: This was a retrospective study and 174 infants who had open heart surgery at P University Hospital, and whose body temperature body temperature exceeded $37.2^{\circ}C$ were included in the study. The assessment tool was composed of 32 items was used for assessment of fever therapy, physiological indexes and antifebrile duration. Physiological indexes included systolic blood pressure, diastolic blood pressure, heart rate, pH, $PaCO_2$, $PaO_2$, $HCO_3{^-}$, $SaO_2$, and $K^+$ and the antifebrile duration was minutes from having a fever until BT returned to normal levels. Results: The antifebrile duration with the hypothermia blanket was shorter than with rectal antipyretics. There were significant differences in the physiological indexes with either type of antifebrile therapy, but drop in BT was greater with the hypothermia blanket than rectal antipyretics. Conclusion: The results of this study indicate that a hypothermia blanket is a non-invasive, non-drug and safe antifebrile therapy. Therefore, a hypothermia blanket can be applied to infants with a fever following open heart surgery.

• 한국기계가공학회지
• /
• 제20권5호
• /
• pp.121-127
• /
• 2021

Reverse offset printing is considering as an emerging technology for printed electronics owing to its environmentally friendliness and cost-effectiveness. In reverse offset printing, selecting the materials for cliché and blanket is critical because of its minimum resolution, registration errors, aspect ratio of reliefs, pattern area, and reusability. Various materials such as silicon, quartz, glass, electroplated nickel plates, and imprinted polymers on rigid substrates can be used for the reverse offset printing of cliché. However, when new structures are designed for specific applications, new clichés need to re-fabricated each time employing multiple time-consuming and costly processes. Therefore, by modifying the blanket materials containing the printing ink, several new structures can be easily created using the same cliché. In this study, we investigated various elastomeric materials and evaluated their applicability for designing a highly stretchable blanket with controlled elastic deformation to implement tunable reverse offset printing.

• 대한기계학회논문집B
• /
• 제38권8호
• /
• pp.709-714
• /
• 2014

리버스 옵셋 인쇄는 인쇄전자를 위한 미세 패터닝기술 중 하나로서 수 ${\mu}m$ 이하의 선폭을 구현할 수 있다. 옵셋 인쇄의 특성상 잉크는 PDMS 재질의 블랑켓에 전사된 후 음각으로 패턴된 클리쉐에 접촉하여 불필요한 패턴을 제거하게 되는데, 이 때 블랑켓은 압력에 의하여 음각 패턴 내부로 침투하는 변형이 발생한다. 이러한 변형은 인쇄 압력에 비례하며, 과도한 인쇄 압력은 넓은 면적의 패턴을 인쇄할 때 클리쉐 패턴의 바닥에 블랑켓이 닿는 불량을 일으키게 된다. 이 논문에서는 리버스 옵셋 인쇄에서 가압변위에 따른 PDMS 블랑켓의 변형을 유한요소기법을 이용하여 모델링하고 접촉압력 대비 변형량을 예측함으로써 실제 인쇄 장비의 실험 결과와 비교하여 인쇄결함이 발생하지 않도록 하는 클리쉐의 제작조건을 제시하고자 한다.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1131-1140
• /
• 2011

A new rotary gravure-offset printing unit is constructed by paralleling a gravure plate cylinder, a blanket cylinder and a impression roller. A Muti-Unit Gravure-Offset Printing Press(MUGOP) equipped with a series of the 3 printing units is utilized for roll-to-roll fine printing. Its core technology is precise over-piling printing of fine patterns. The severe problems of 'slurring' and 'doubling' in typical offset printing are unavoidable, which can be eliminated by applying a soft pad-type blanket cylinder and the unique 'true rolling' technique. Nip pressure between the blanket cylinder and the plate cylinder is measured by the constant pressure control system which equipped with load cells attached on the cylinders' axes. The running circumference of the blanket cylinder is increased to reach the same circumference of the plate cylinder as the pressure increasing, so that the specifications of the blanket cylinder is determined by the relationships of its shore hardness, diameter and nip pressure. When a softer blanket is used, a blanket cylinder of smaller diameter could give higher nip pressure. Realization of the true rolling technique on the MUGOP makes multilayer printing possible as well as fine printing in printed electronics.

• 중환자간호학회지
• /
• 제10권3호
• /
• pp.53-64
• /
• 2017

Purpose : This study investigated the effects of active warming using a Warm Touch warming system or a cotton blanket in postoperative patients after general anesthesia for abdominal surgery. Methods : This quasi-experimental study utilized two experimental groups and one control group: a cotton-blanket group (n = 25) were warmed with a cotton blanket and a sheet; a forced-air warming group (n = 24) were warmed with a Warm Touch warming system, a cotton blanket, and a sheet; and a control group (n = 25) were warmed with a sheet. Measurement variables were postoperative pain, body temperature, and thermal discomfort. Data were analyzed using a one-way ANOVA, ${\chi}^2-tests$, Fisher's exact test, and a repeated measures ANOVA. Results : The effects of active warming using a Warm Touch warming system and a cotton blanket on postoperative patients was significant in reducing pain (F = 13.91, p < .001) and increasing body temperature (F = 12.49, p < .001). Conclusion : Active warming made a significant difference in pain and body temperature changes. Active warming methods may help patients' postoperative recovery and prevent complications. Further research is needed to explore the effects and side effects of active warming on recovering normothermia.

• 한국안전학회지
• /
• 제27권6호
• /
• pp.14-19
• /
• 2012

The Helium cooled ceramic reflector(HCCR) test blanket module(TBM) has been designed and developed to participate the ITER(International Thermonuclear Experimental Reactor) test blanket program in Korea. The TBM was one of the main objectives for developing ITER for proving the tritium self-sufficiency and the heat transfers to produce the electricity with the breeding blanket concept. Among the TBM components, the first wall(FW) was the most important component in safety since it was directly faced a high level of a heat and fast neutrons from the plasma side and could protect the others components inside TBM. In this paper, the FW has been designed through the thermo-mechanical analysis considering ITER operation conditions. With the developed simple models, the stress limit analysis based on RCC-MR code which is the nuclear power plant design codes in France was evaluated for the allowable design criteria. The results showed that the designed FW model satisfied $1.5S_m$ or $3S_m$ of the allowable stress($S_m$) in RCC-MR code at the maximum stress region in the FW.

• Geomechanics and Engineering
• /
• 제35권4호
• /
• pp.385-393
• /
• 2023

To analyze the consolidation with horizontal sand drains, the plane strain consolidation model under multi-ramp loading is established, and its corresponding analytical solution is derived by using the separation of variables method. The proposed solution is verified by the field measurement data and finite element results. Then, the effects of the loading mode and stress distribution on consolidation and dissipation of pore pressure are investigated. At the same time, the influence of hydraulic conductivity and thickness of sand blankets on soil consolidation are also analyzed. The results show that the loading mode has a significant effect on both the soil consolidation rate and generation-dissipation process of pore water pressure. In contrast, the influence of stress distribution on pore pressure dissipation is obvious, while its influence on soil consolidation rate is negligible. To guarantee the fully drained condition of the sand blanket, the ratio of hydraulic conductivity of the sand blanket to that of clay layer k_d/k_v should range from 1.0×10⁴ to 1.0×10⁶ with soil width varying from 100 m to 1000 m. A larger soil width correspondingly needs a greater value of kd/kv to make sure that the pore water can flow through the sand blanket smoothly with little resistance. When the soil width is relatively small (e.g., less than 100 m), the effect of thickness of the sand blanket on soil consolidation is insignificant. And its influence appears obvious gradually with the increase of the soil width.

• 한국환경과학회지
• /
• 제4권3호
• /
• pp.87-87
• /
• 1995

This study was investigated with denitrification of wastewater containing nitrate using upflow sludge blanket process. Contents of this study were the nitrogen gas Production, relationship between HRT and COD/$NO_3^--N$ ratio in case of various hydrogen donor addition, relationship between nitrate loading rate and various hydrogen donor addition.