• 한국수산과학회지
• /
• 제36권5호
• /
• pp.541-548
• /
• 2003

Species identification in hydroacoustic survey is one of the key requirements to estimate biomass of organism and to understand the structure of zooplankton community. Feasibility of species identification using two frequencies (38 and 120 kHz) was investigated on the basis of mean volume backscattering strength difference (MVBS). Virtual echogram technique was applied to two frequencies data sets that obtained from surveys in the Antarctic Ocean and Yellow Sea. Virtual echogram method using MVBS revealed the possibility of species identification, which species identification relying on visual scrutiny of single frequency acoustic data resulted in significant errors in biomass estimation. Through noise cancellation using MVBS, much of the acoustic noise caused by acoustic instruments could be removed in new virtual echogram, and the biomass estimation and data quality was improved.

• 한국수소및신에너지학회논문집
• /
• 제18권1호
• /
• pp.85-94
• /
• 2007

Rice straw, produced as an agricultural by-product, is usable biomass as fuels if depolymerized to monomer unit, because the chemical structure are similar to high octane materials found in gasoline. In this study, parameters of thermochemical degradation by solvolysis reaction of rice straw such as the effect of reaction temperature, reaction time and type of solvent on conversion yield and degradation products were investigated. It was found that the effectiveness of the solvent on the solvolysis reaction was as follows; acetone>cresol>butanol. When acetone was used as a solvent, the highest rice straw conversion was observed to be 91.5% at $500^{\circ}C$, 40 min. Combustion heating value of liquid products from thermochemical conversion processes was in the range of 7,380 cal/g. The energy yield and mass yield in acetone-solvolysis of rice straw was as high as 69.0% and 38.2 g-oil/100g-raw material after 40 min of reaction at $350^{\circ}C$. Various aliphatic and aromatic compounds were detected in the rice straw solvolysis products. The major components of the solvolysis products, that could be used as fuel, were 4-methyl-2-pentanone, 3,5,5-trimethyl-2-cyclopentan-1-one as ketones.

• 한국수산과학회지
• /
• 제43권3호
• /
• pp.246-253
• /
• 2010

The marine algal flora and community structure were investigated at three sites in Ulsan on the southeast coast of Korea between August 2005 and July 2006. Ninety-one benthic algae species were identified, including 14 Chlorophyta, 21 Phaeophyta, and 56 Rhodophyta species. Of the 91 seaweeds, 19 species were found throughout the survey period. The wet weight biomass ranged from 310.8 to 2,960.4 g $m^{-2}$ during the study period. The maximum biomass was recorded at Sinri, and the minimum was recorded at Daesong. The R/P, C/P and (R+C)/P values reflecting flora characteristics were 2.67, 0.67, and 3.33, respectively. The flora investigated could be classified into six functional groups: coarsely branched (46.2%), thick leathery (22.0%), filamentous (16.5%), Sheet (7.7%), jointed calcareous (4.4%), and crustose (3.3%) forms. A cluster analysis produced two groups that differed meaningfully: one included the site Sinri-summer and the other included the sites Daesong and Jinha.

• Elastomers and Composites
• /
• 제56권3호
• /
• pp.136-151
• /
• 2021

Biomass lignin, a waste produced during the paper and bio-ethanol production process, is a cheap material that is available in large quantities. Thus, the interest in the valorization of biomass lignin has been increasing in industrial and academic areas. Over the years, lignin has been predominantly burnt as fuel to run pulping plants. However, less than 2% of the available lignin has been utilized for producing specialty chemicals, such as dispersants, adhesives, surfactants, and other value-added products. The development of value-added lignin-derived co-products should help make second generation biorefineries and the paper industry more profitable by valorizing lignin. Another possible approach towards value-added applications is using lignin as a component in plastics. However, blending lignin with polymers is not simple because the polarity of lignin molecules results in strong self-interactions. Therefore, achieving in-depth insights on lignin characteristics and structure will help in accelerating the development of lignin-based products. Considering the multipurpose characteristics of lignin for producing value-added products, this review will shed light on the potential applications of lignin and lignin-based derivatives on polymeric composite production. Moreover, the challenges in lignin valorization will be addressed.

• Journal of Electrochemical Science and Technology
• /
• 제10권2호
• /
• pp.159-169
• /
• 2019

The activated carbon materials were prepared from waste biomass by ultrasonic assisted chemical activation method (UCA), ultrasonic assisted physical activation method (UPA) and Manganese nitrogen doped carbon (Mn/N-C). The XRD result shows the turbostatic (fully disordered) structure. The cyclic voltammetry test was done at 50 mV/s using 1M sodium sulfate and the values of specific capacitance were found to be 93, 100 and 115 F/g for UCA, UPA and Mn/N-C respectively. The power density values for the samples UCA, UPA and Mn/N-C were found to be 46.04, 87.97 and 131.42 W/kg respectively. The electrochemical impedance spectroscopy was done at low frequency between 1 to 10 kHz. The Nyquist plot gives the resistant characteristics of the materials due to diffusional resistance at the electrode-electrolyte interface. The Energy Dispersive X-Ray Spectroscopyanalysis (EDAX) analysis showed that the percentage doping of nitrogen and manganese were 3.53 wt% and 9.44 wt% respectively. It is observed from the experiment Mn/N-C doped carbon show good physical and electrochemical properties.

• 한국입자에어로졸학회지
• /
• 제17권4호
• /
• pp.125-132
• /
• 2021

Fresh PM_2.5 smokes emitted from combustion of four biomass materials (pellet, palm fruit fiber (PFF), PKS, and sawdust) in a laboratory-controlled environment were characterized using an attenuated total reflectance-fourier transform infrared (ATR-FTIR) technique. In smoke samples emitted from combustion of pellets, PFF and PKS, which is being used as boiler fuels for greenhouses in rural areas, the organic carbon/elemental carbon (OC/EC) ratios in PM_2.5 were very high (14.0-35.5), whereas in sawdust smoke samples they were significantly low (<4.0) due to the combustion method close to flaming combustion. ATR-FTIR analysis showed that OH(3400-3250 cm^-1), CH₃(2958-2840 cm^-1), CH₂(2910 cm^-1 and 2850 cm^-1), ketone(1726-1697 cm^-1), C=C(1607-1606 cm^-1 and 1515-1514 cm^-1), lignin (1463-1462 cm^-1 and 1430-1428 cm^-1) and -NO₂(1360-1370 cm^-1) peaks were identified in all biomass burning (BB) smoke samples. However, additional peaks appeared depending on the type of biomass. Among the four types of biomass materials, an additional peak of the methylene group CH₃(2872-2870 cm^-1) appeared only in PFF and PKS smoke samples, and a peak of C=O(1685 cm^-1) was also confirmed. And in the case of PKS smoke samples, a peak of aromatic C=C(1593 cm^-1 and 1476 cm^-1) that did not appear in other BB samples was also observed. This indicates that the molecular structure of organic compounds emitted during BB differs depending on the type of biomass materials. The results of this study are expected to provide valuable information to more specifically reveal the effect of BB on PM_2.5 collected in the atmospheric environment.

• 한국염색가공학회지
• /
• 제5권3호
• /
• pp.221-228
• /
• 1993

Cellulose acetate and methyl cellulose were synthesized from waste cellulose in order to make waste knit on value added highly. Crystal waste cellulose by oxidation using $HIO_4$ and then acetylation was decrystallized. A degee of crystallinity was measured by X-ray diffraction and the structure was identified by FT-IR spetroscopy, respectively. Cellulose acetate was prepared from the reaction of decrystallized cellulose with acetic acid, cone-$H_{2}SO_{4}$ and acetic anhydride. Also, structure identification by FT-IR and a degree of crystallinity by X-ray diffraction were performed. DS of the synthesized cellulose acetate was 2.8 and viscosity average molecular weight was 238,000. Also, methyl cellulose was synthesized by treating cellulose acetate with NaOH and iodomethane. DS of the synthesized methyl cellulose was 3.0. Glucose unit with three hydroxy groups was all substituted by methoxyl groups. It was identified by FT-IR spectroscopy. Also, the thermal properties of the synthesized methyl cellulose were examined by DSC. It shewed two shewed melting peaks at 22$0^{\circ}C$ and 24$0^{\circ}C$ in the 2nd scan. It proved that DS=3.0 of methyl cellulose was a thermotropic liquid crystal.

• Ocean and Polar Research
• /
• 제33권3호
• /
• pp.193-209
• /
• 2011

The community structure of meiobenthos was studied at 16 stations within sandy tidal and subtidal zones in Jangbongdo in the Yellow Sea, Korea from Aug. 2006 to Jan. 2007. Meiobenthic organisms were collected by three core samples, with a 3.6 cm diameter, from each sediment sample taken with a Smith-McIntyre Grab. Mean grain size of study stations ranged from $1.49{\phi}$ to $3.55{\phi}$. Composition of sand ranged from 80.38% to 99.89%. There was reduction in total abundance and biomass of meiobenthos from summer to winter. Total densities of meiofauna ranged between 17 inds./10 $cm^2$ and 853 inds./10 $cm^2$. Nematodes, gastrotricha, nauplius and harpacticoids appeared as major taxa in decreasing order. This study shows that major taxa comprised 90 percent of total abundance. Most meiofaunal organisms are concentrated in the upper sediment layers and the total abundance and biomass of organisms in the tidal zone is higher than the subtidal zone.

• Journal of Microbiology and Biotechnology
• /
• 제28권4호
• /
• pp.571-578
• /
• 2018

Biofuel production using lignocellulosic biomass is gaining attention because it can be substituted for fossil fuels without competing with edible resources. However, because Saccharomyces cerevisiae does not have a ${\text\tiny{D}}$-xylose metabolic pathway, oxidoreductase or isomerase pathways must be introduced to utilize ${\text\tiny{D}}$-xylose from lignocellulosic biomass in S. cerevisiae. To elucidate the biochemical properties of xylose isomerase (XI) from Piromyces sp. E2 (PsXI), we determine its crystal structure in complex with substrate mimic glycerol. An amino-acid sequence comparison with other reported XIs and relative activity measurements using five kinds of divalent metal ions confirmed that PsXI belongs to class II XIs. Moreover kinetic analysis of PsXI was also performed using $Mn^{2+}$, the preferred divalent metal ion for PsXI. In addition, the substrate-binding mode of PsXI could be predicted with the substrate mimic glycerol bound to the active site. These studies may provide structural information to enhance ${\text\tiny{D}}$-xylose utilization for biofuel production.

• Carbon letters
• /
• 제25권
• /
• pp.103-112
• /
• 2018

Hierarchically porous, chemically activated carbon materials are readily derived from biomass using hydrothermal carbonization (HTC) and chemical activation processes. In this study, empty fruit bunches (EFB) were chosen as the carbon source due to their sustainability, high lignin-content, abundance, and low cost. The lignin content in the EFB was condensed and carbonized into a bulk non-porous solid via the HTC process, and then transformed into a hierarchical porous structure consisting of macro- and micropores by chemical activation. As confirmed by various characterization results, the optimum activation temperature for supercapacitor applications was determined to be $700^{\circ}C$. The enhanced capacitive performance is attributed to the textural property of the extremely high specific surface area of $2861.4m^2\;g^{-1}$. The prepared material exhibited hierarchical porosity and surface features with oxygen functionalities, such as carboxyl and hydroxyl groups, suitable for pseudocapacitance. Finally, the as-optimized nanoporous carbons exhibited remarkable capacitive performance, with a specific capacitance of $402.3F\;g^{-1}$ at $0.5A\;g^{-1}$, a good rate capability of 79.8% at current densities from $0.5A\;g^{-1}$ to $10A\;g^{-1}$, and excellent life cycle behavior of 10,000 cycles with 96.5% capacitance retention at $20A\;g^{-1}$.