• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.438-438
• /
• 2010

The abnormal behavior of the argon metastable density during the E-H mode transition in argon ICP discharge was investigated. Lots of investigations including global models expected that during and after the mode transition of ICP discharge, the density of metastable increases with applied rf power (i.e. electron density). However, recent direct measurement of metastable density revealed that the metastable density of argon decreases with the applied power during and after the mode transition. This result may not be explained by the previous global model which is based on the assumption of the Maxwellian electron energy distribution function (EEDF). In this paper, to explain this abnormal behavior with simple manners, a simple global model taking account of the effect of the non-Maxwellian EEDFs incorporating into a set of coupled rate equations is proposed. The result showed that the calculated metastable density taking account of non-Maxwellian EEDF and its evolution during the transition has an abnormal behavior with electron density and is in good agreement with the previous measurement results, indicating the close coupling of electron kinetics and the behavior of metastable density. The proposed simple model is expected to provide qualitative kinetic insight to understand the behavior of the metastable density in various plasma discharges which typically exhibit non-Maxwellian distribution.

• 한국정밀공학회지
• /
• 제30권4호
• /
• pp.414-420
• /
• 2013

We developed inkjet based measurement system for micro-droplet behavior on a substrate. By using the inkjet dispenser, a droplet, which is as small as few pico-liter in volume, can be jetted and the amount can be controlled. After jetting, the droplet image on the substrate is acquired from side view camera. Then, droplet profile is extracted to measure droplet volume, contact angle and evaporation characteristics. Also top view image of the droplet is acquired for better understanding of droplet shape. The previous contact angle measurement method has limitations since it mainly measures the ratio of height and contact diameter of droplet on a substrate. Unlike previous measurement system, our proposed method has advantages because various behavior of droplet on substrate can be effectively analyzed by extracting the droplet profile.

• Smart Structures and Systems
• /
• 제20권5호
• /
• pp.563-572
• /
• 2017

The safety of structures is closely associated with the structural out-of-plane behavior. In particular, long and slender beam structures have been increasingly used in the design and construction. Therefore, an evaluation of the lateral and torsional behavior of a structure is important for the safety of the structure during construction as well as under service conditions. The current contact measurement method using displacement meters cannot measure independent movements directly and also requires caution when installing the displacement meters. Therefore, in this study, a vision-based system was used to measure the in-plane and out-of-plane displacements of a structure. The image processing algorithm was based on reference objects, including multiple targets in Lab color space. The captured targets were synchronized using a load indicator connected wirelessly to a data logger system in the server. A laboratory beam test was carried out to compare the displacements and rotation obtained from the proposed vision-based measurement system with those from the current measurement method using string potentiometers. The test results showed that the proposed vision-based measurement system could be applied successfully and easily to evaluating both the in-plane and out-of-plane movements of a beam including twisting rotation.

• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.23-27
• /
• 1999

The measurement of thr high-temperature strains is one of the challenging subjects in mechanical engineering. For the precise measurement, proper high-temperature strain gauge, cement and skilled technique are needed. In this paper, a high-temperature strain measurement is performed for the perfectly flat CRT. As this CRT is structurally very weak, cracking of the panel frequently occurs during the heat cycle in the furnace. From the measured strain variations of the panel with tension shadow mask, the crack behavior can be explained.

• 한국콘텐츠학회논문지
• /
• 제16권1호
• /
• pp.362-369
• /
• 2016

최근 다양한 중대형 교량구조물의 안전상황을 점검하기 위하여 여러 가지의 계측장비를 이용하고 있지만 대부분 일정한 주기별로 교량의 변위거동을 측정하고 확인하는 방법을 사용하고 있다. 본 연구에서는 지구전체를 실시간으로 관측할 수 있는 인공위성 GPS 신호를 수신하여, 교량 각 구조부의 변위와 거동 특성을 실시간으로 24시간 내내 mm 단위로 자동 계측하여, 계측 정보 및 데이터를 무선 네트워크로 전송하여 사용할 수 있도록 함으로써, 미세한 거동 변위를 자동으로 통보할 수 있게 하는 GNSS와 연계한 실시간 교량 모니터링 시스템을 적용하였다. 이를 위하여 실제로 중대형의 노후화된 교량상부에 GNSS 수신기를 설치하여 그 측량자료를 수신하여 분석하고, USN과 동시에 측정하여 3차원의 위치정보로 나타내어 교량변위를 실시간으로 모니터링 할 수 있는 실험연구를 실시하였다 그 결과, 한 측정지점에서 하루의 측정 시간에서도 약 0.027~0.037m에서 수직변위가 반복되고 있음을 확인할 수 있었다.

• Design & Manufacturing
• /
• 제17권1호
• /
• pp.1-5
• /
• 2023

In multi-material injection molding, since two or more materials with different process conditions are used, it is essential to maximize process efficiency by operating the cooling or heating system to a minimum. In this study, Liquid silicone rubber (LSR) that can be cured at a low temperature suitable for the multi-material injection molding was selected and the cure behavior according to the process conditions was analyzed through differential scanning calorimetry (DSC). Dynamic measurement results of DSC with different heating rate were obtained, and through this, the total heat of reaction when the LSR was completely cured was calculated. Isothermal measurement results of DSC were derived for 60 minutes at each temperature from 80 ℃ to 110 ℃ at 10 ℃ intervals, and the final degree of cure at each temperature was calculated based on the total heat of reaction identified from the Dynamic DSC measurement results. As the result, it was found that when the temperature is lowered, the curing start time and the time required for the curing reaction increase, but at a temperature of 90 ℃ or higher, LSR can secure a degree of cure of 80% or more. However, at 80 ℃., it was found that not only had a relatively low degree of curing of about 60%, but also significantly increased the curing start time. In addition, in the case of 110 ℃, the parameters were derived from experimental result using the Kamal kinetic model.

• 한국항만학회지
• /
• 제14권1호
• /
• pp.115-124
• /
• 2000

This study is a suggest a measurement method of lateral displacement, which can be used to judge the stability of bridge abutment on soil undergoing lateral movement. The abutment of bridge on soft foundation makes lateral movement due to the settlement of back fill and lateral flow. To measure the displacement of such a abutment, there are a lot of indirect method for measurement such as survey of leveling or inclinometer gauge around the abutment. But all of them are not sufficient to confirm the ground behavior and measure the exact lateral behavior of structure. As making the structure and pile cooperatively by measuring the movement of lateral displacement, for measuring the abutment displacement precisely by using the inclinometer. In this work, we try to suggest efficient measuring method of abutment displacement and its application.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.723-728
• /
• 2006

In this paper, we present a new system, OPTISCOPE SA, especially designed for precise measurement of temporal behavior of LCD displays. We show that gray to gray level response time measurement requires a very sensitive and precise instrument and also that the capacity to measure luminance levels and gamma curve can be useful. Quite often, precise evaluation of LCD response time needs also use of low pass and stop band filters to suppress noise and flicker. Low pass filters affect the results but can be corrected for simple temporal behaviors. For complex temporal behaviors like those observed for overdriven LCDs, we show that direct adjustment of theoretical responses is much more efficient to get a complete picture of the temporal behavior of such displays.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.115-115
• /
• 2010

This paper introduces a measurement system that measures behavior and electrical characteristics of overhead contact line irregular sections in real-time. For verification, we developed a prototype of the real-time overhead contact line irregular section behavior measurement system and a monitoring system for field tests. The current and temperature of contact wires and messenger wires were measured real-time by applying the system at KTX a commercial line. Therefore, acquiring data is possible with the developed system and this system that measures one of the fundamental and key factors, the catenary current, should be applicable to various areas such as detecting characteristics for designing overhead contact lines, enhancing speed, and enhancing energy.

• Industrial Engineering and Management Systems
• /
• 제2권1호
• /
• pp.55-62
• /
• 2003

This paper deals with the difficulties involved in analyzing and designing a management system to reduce the risks and improve the productivity of new product development. In this paper, a method is described to analyze user information and determine product specifications based on a stimulus-response model, the conjoint measurement of users needs, and product characteristics deployment. The proposed method can analyze the effect of a partial price on the contribution ratio based on the order of preference of product profiles through a smaller number of product profiles. The strengths and weaknesses of this method are examined as the method is applied to the case study of a mobile computer intended for personal use.