• 전자공학회논문지
• /
• 제51권6호
• /
• pp.228-236
• /
• 2014

견인 선배열 소나는 해양이라는 유체에서 작동하기 때문에 그 형상이 왜곡되고, 특히 견인 함정이 회전하는 경우 형상이 심하게 변형된다. 이러한 경우 선배열이 갖는 빔 패턴 형성은 제한되며, 이로 인한 신호 대 잡음비 등의 성능 저하를 야기한다. 본 논문에서는 2단 최소자승법에 기초한 개선된 2단 최소자승법 알고리즘을 제안하였으며, 해양에서 운용되는 선배열의 형상을 변침각도로 모델링하여 알고리즘을 적용하였다. 변침각도와 주엽의 위치를 변경하면서, 알고리즘별 조향 빔의 신호 대 잡음비를 분석하였다. 그 결과 제안한 알고리즘이 다른 알고리즘보다 2dB 정도 성능이 향상되었으며, 비교적 일정한 빔 패턴을 형성하였다.

• Nuclear Engineering and Technology
• /
• 제55권3호
• /
• pp.919-926
• /
• 2023

To analyze the cause of the destruction of thin, carbon-backed lithium fluoride targets during a measurement of the fusion of ⁷Li and ¹⁷O, we estimate theoretically the lifetimes of carbon and LiF films due to sputtering, thermal evaporation, and lattice damage and compare them with the lifetime observed in the experiment. Sputtering yields and thermal evaporation rates in carbon and LiF films are too low to play significant roles in the destruction of the targets. We estimate the lifetime of the target due to lattice damage of the carbon backing and the LiF film using a previously reported model. In the experiment, elastically scattered target and beam ions were detected by surface silicon barrier (SSB) detectors so that the product of the beam flux and the target density could be monitored during the experiment. The areas of the targets exposed to different beam intensities and fluences were degraded and then perforated, forming holes with a diameter around the beam spot size. Overall, the target thickness tends to decrease linearly as a function of the beam fluence. However, the thickness also exhibits an increasing interval after SSB counts per beam ion decreases linearly, extending the target lifetime. The lifetime of thin LiF film as determined by lattice damage is calculated for the first time using a lattice damage model, and the calculated lifetime agrees well with the observed target lifetime during the experiment. In experiments using a thin LiF target to induce nuclear reactions, this study suggests methods to predict the lifetime of the LiF film and arrange the experimental plan for maximum efficiency.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.519-522
• /
• 2002

An active phased array antenna consists of many channels. Each channel has a different initial phase shift and gain because of the inequality in the active circuits themselves, interface between radiators and active circuits, and beam-forming circuits and other antenna system configurations. This raises an inherent problem in active phased array antennas. To compensate for this problem the initial phase and gain of each channel should be calibrated. This paper presents an efficient calibration method for an initial phase variation of each channel in active phased array antennas. We tested our method in an active phased array antenna, and obtained good results in the radiation pattern and beam direction of antenna.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.145-155
• /
• 1995

Continuous wave C $O_{2}$ laser beam welding and formability of zinc coated steel plates were investigated. First, the optimal welding condition could be obtained in lap configuration by using the data for heat input, gap size and fracture behaviour. The gap size for fully-penetrated bead could be predicted by the gap model by Akhter et al. AIso, it was found that the joining efficiency was constant. Secondly, the butt welding of dissimilar materials (zinc coated steel plate and cold rolled steel plate) with different thicknesses was investigated. In the thickness range of 0.8-2.0 mm, the maximum welding speed of 10m/min was obtained. In the butt welding of two plates with thickness 2.0 mm and l.6mm, the maximum, welding speed of 6m/min was obtained, Finally. the forming results of butt-welded plates showed that the joining design was important to apply the laser welded blank in the automotive production.

• 한국정밀공학회지
• /
• 제15권4호
• /
• pp.58-67
• /
• 1998

A sectional analysis of sheet metal forming process with an arbitrary tool shape is proposed in the present work. To improve the numerical convergence in the conventional membrane sectional analysis, the Bending Energy Augmented Membrane (BEAM) elements had been developed. The BEAM elements particularly improve the stability and convergence of the finite element method for the case of deep drawing. In this work, the FERGUBON spline (C$^2$-continuous) was used to fit the deformed mesh to smooth the given curves and calculate the local curvature of the deformed sheet. The fittings of the deformed sheet and tool surface profile ensure the stability and the convergence of the finite element analysis of highly nonlinear stamping processes. A center floor section and front fender section are analyzed to show the accuracy and robustness of the approach. The results obtained by the proposed approach are compared with the available experimental data.

• Journal of Communications and Networks
• /
• 제7권3호
• /
• pp.258-262
• /
• 2005

An adaptive beamforming system based on code filtering and differential correlation approaches is proposed. The differential correlation method was originally proposed for time delay estimation of direct sequence code division multiple access (DS-CDMA) systems under near-far ratio conditions and the code filtering correlation algorithm, on the other hand, was proposed for array response estimation in DS-CDMA systems under perfect power control. In this paper, by combining differential correlation concept with the code filtering beamforming technology, an accurate estimate of the beam forming weights and an enhanced performance of DS-CDMA systems under sever near-far ratio conditions is achieved. The system performance in terms of beam pattern and bit-error-rate (HER) shows that the proposed adaptive beamformer outperforms the conventional code filtering correlation technique.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.517-522
• /
• 2011

Most of SEM is double condenser lens system. Two condenser lenses are required to provide the high demagnification ratios necessary for forming nanometer probes. The thin lens concept provides a highly useful basis for preliminary calculations in a broad range of situations. It is an easy way to understand the electron beam paths in column. Demagnification is easily calculated by this method. In this paper, we present design processes for condenser lens's demagnification by using thin lens combination model. Also, we verify the reliability of our design processes by comparing the modeled demagnification with these of corrected condenser lens.

• Journal of the Optical Society of Korea
• /
• 제18권4호
• /
• pp.406-413
• /
• 2014

An optical true-time delay beam-forming system using a tunable dispersion compensating module (DCM) for dense-wavelength division modulation (DWDM) and a multiwavelength fiber ring laser for a phased array antenna is proposed. The multiwavelength fiber ring laser has one output that includes four wavelengths; and four outputs that include only single-wavelength. The advantage of such a multiwavelength fiber ring laser is that it minimizes the number of devices in the phased array antenna system. The time delays according to wavelengths, which are assigned for each antenna element, are obtained from the tunable DCM. The tunable DCM based on a temperature adjustable Fabry-Perot etalon is used. As an experimental result, a DCM could be used to obtain the change of the beam angle by adjusting the dispersion value of the DCM at the fixed lasing wavelengths of the fiber ring laser in the proposed optical true-time delay.

• 한국컴퓨터정보학회논문지
• /
• 제8권1호
• /
• pp.90-96
• /
• 2003

본 논문에서는 N개의 등방성 점원을 수신 지역과 동일한 구조로 배열하고 수신 지역과 동일한 방사패턴을 갖는 배열 구조에 대하여 연구하였다. 배열된 소자 간격은 그레이팅 로브를 피하면서 최적의 특성을 얻기 위하여 반파장 등간격으로 선택하였고, 각 배열 구조의 어레이 팩터를 유도한 후, 방사패턴을 이론적으로 계산하였다. 계산된 특성으로부터 각 평면 배열 안테나의 방사패턴은 수신 지역의 구조와 유사한 빔 특성을 얻을 수 있었다.

• Journal of electromagnetic engineering and science
• /
• 제15권1호
• /
• pp.37-43
• /
• 2015

We implemented a real-time radar system for an unmanned ground vehicle designed to run on unpaved or bumpy roads. The system must be able to detect slow targets in a cluttered environment and cover wide angular sections with high resolution at the same time. The system consists of array antennas, preprocessors for digital beam forming, and digital signal processors for the detection process which uses sawtooth waveforms and high-resolution estimation, and is called forward/backward spatial smoothing beamspace multiple signal classification (FBSS BS-MUSIC). We show that the sawtooth waveforms enhance the angular estimation capability of FBSS BS-MUSIC in addition to their well-known advantages of removing the ambiguity of targets and detecting slow targets with improved velocity resolution.