• 대한기계학회논문집A
• /
• 제40권5호
• /
• pp.513-523
• /
• 2016

단순보와 외팔보의 U-노치 및 균열에 대한 응력집중계수 및 응력확대계수를 유한요소법 및 광탄성실험에 의해 해석하였다. 해석결과를 사용하여 응력집중계수 및 응력확대계수의 추정 그래프를 얻었다. 노치의 응력집중계수해석을 위하여 무차원 노치 길이 H(시편의 높이)/h=1.1~2, 무차원 틈 간격 r(노치선단의 반경)/h=0.1~0.5로 하였다. 여기서 h=H-c, c=노치길이이다. 해석결과 틈 길이가 증가할수록 그리고 틈 간격이 좁아질수록 응력집중계수는 증가 한다. 응력집중계수는 단순보가 외팔보다 더 크게 나타나나, 실제 일정한 하중과 노치길이 및 틈 간격 하에서 최대 응력값은 단순보보다 외팔보에서 크게 발생함을 알 수 있었다. 균열해석을 위하여 무차원 균열길이 a(균열길이)/H=0.2~0.5로 하였다. 균열의 길이가 증가 할수록 무차원 응력확대계수는 증가한다. 일정한 하중과 일정한 균열길이하에 응력확대계수값은 단순보 보다 외팔보에서 크게 발생함을 알 수 있었다.

• Journal of Welding and Joining
• /
• 제15권3호
• /
• pp.79-87
• /
• 1997

This study was performed to evaluate basic characteristics of electron beam welding process for a 9% Ni steel plate. The principal welding process parameters, such as working distance, accelerating voltage, beam current and welding speed were investigated. The AB (Arata Beam) test method was also applied to characterize beam size and energy density of the electron beam welding process. The electron beam size was found to decrease with the increase of accelerating voltage and the decrease of working distance. So, in case of high voltage (150kV), spot size and energy density of electron beam were revealed to be 0.9mm and $6.5\times10^5W/\textrm{cm}^2$ respectively. The accelerating voltage among the welding parameters was found to be the most important factor governing the penetration depth. When the accelerating voltage of electron beam was low ($\leq$90kV), beam current and welding speed did not affect on the penetration depth significantly. However, in case of high voltage ($\geq$120kV), the depth of penetration increased very sensitively with the increase of beam current and the decrease of welding speed.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.585-587
• /
• 2009

A large diameter slot waveguide made backward wave oscillator is investigated experimentally. The parameters of slow wave structure are chosen so that the oscillation frequency is about 20 GHz. Plasma is produced by the beam and it has favorable effects on beam propagation and Cherncov oscillation. The output power strongly enhanced when the guiding magnetic field approaches to the fundamental electron cyclotron resonance.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.178-183
• /
• 1998

This paper examines the crack growth behavior of 7075-T651 and 5052-H32 aluminum alloys for variable load within tensile load range condition. The cantilever beam type specimen with a chevron notch is used in this study. The crack growth and closure are investgated by compliance method. The applied initial stress ratio is R=0.3 and variable load are R=0.65, 0.46. Crack length, stress intensity factor range, ratio of effective stress intensity factor range and crack growth rate etc. are inspected with fracture mechanics estimate.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.391-395
• /
• 1997

The transmission of sound and vibration through structures is of interest in many noise control problems, including architectural acoustics, sound transmission through air craft, spacecraft and ship, and the transmission of noise through machinery and engine enclosures. Statistical Energy Analysis provides a simple and accurate method of approaching these problems. In this paper, comparing the measured coupling loss factor of plate-beam with measured coupling loss factor of mass on the junction will be inspected.

• Structural Engineering and Mechanics
• /
• 제46권1호
• /
• pp.39-51
• /
• 2013

An extremum method is presented to predict the wrinkling characteristics of the inflated cone in bending. The wrinkling factor is firstly defined so as to obtain the wrinkling condition. The initial wrinkling location is then determined by searching the maximum of the wrinkling factor. The critical wrinkling load is finally obtained by determining the ratio of the wrinkling moment versus the initial wrinkling location. The extremum method is proposed based on the assumption of membrane material of beam wall, and it is extended to consider beam wall with thin-shell material in the end. The nondimensional analyses show that the initial wrinkling location is closely related to the taper ratio. When the taper ratio is higher than the critical value, the initial wrinkles will be initiated at a different location. The nondimensional critical wrinkling load nonlinearly increases as the taper ratio increases firstly, and then linearly increases after the critical taper ratio. The critical taper ratio reflects the highest load-carrying efficiency of the inflated cone in bending, and it can be regarded as a measure to optimize the geometry of the inflated cone. The comparative analysis shows fairly good agreement between analytical and numerical results. Over the whole range of the comparison, the mean differences are lower than 3%. This gives confidence to use extremum method for bending-wrinkling analysis of inflated conical cantilever beam.

• 대한방사선기술학회지:방사선기술과학
• /
• 제22권2호
• /
• pp.47-51
• /
• 1999

We calculated the energy distribution and the percentage depth-dose at 10 cm in a $10{\times}10\;cm^2$ with a photon beam at SSD of 100 cm by using a Monte Carlo Simulation. PDD is used as a beam-quality specifier for radiotherapy beams. It is better than the commonly used values of TPR or nominal accelerating potential. The presence of electron contamination affects the measurement of PDD, but can be removed by the use of a 0.1 cm lead filter. It reduces surface dose from contaminant electrons from the accelerator by more than 90% for radiotherapy beams. The filter performs best when it is placed immediately below the head. An electron-contamination correction factor is introduced to correct for electron contamination from the filter and air. It converts PDD which includes the electron contamination with the filter in place into PDD for the photons in the filtered beam. The correction factor can be used to determine stopping-power ratio. Calculations show that the values of water-to-air slopping power ratio in the unfiltered beam are related to PDD.

• Radiation Oncology Journal
• /
• 제11권2호
• /
• pp.455-461
• /
• 1993

Experimental measurements of dose characteristics with pentagonal applicator at nominal energy of 4, 6, 9, 12 and 15 MeV electron beam were performed for intraoperative radiotherapy (IORT) in ML-15MDX linear accelerator. This paper presents the percent depth dose, surface dose, beam flatness and output factors of using the IORT applicator in different electron beam energy. The output factor showed as a 24 percent higher in IORT applicator than that of reference $10{\times}10cm^2$ applicator. The surface dose of using the IORT applicator showed 7.7 and 2.7 percent higher than that of reference field in 4 and 15 MeV electron beam, respectively. In our experiments, the variation of percent depth dose was very small but the output factor and flatnees at 0.5 cm depth have showed a large value in IORT applicator.

• 제어로봇시스템학회논문지
• /
• 제20권6호
• /
• pp.641-646
• /
• 2014

In this paper, we propose a controller for a ball and beam system which reduces the measurement error effect under AC and DC noise. The ball and beam system measures data through a sensor. If sensor noise is included in a controller via the feedback channel, the signal is distorted and the entire system cannot work normally. Therefore, some appropriate action for the measurement error effect is essential in the controller design. Our controller is equipped with a gain-scaling factor and a compensator to reduce the effect of measurement error in the feedback signal. Effectively, our proposed controller can reduce the AC and DC noise of a feedback sensor. We analyze the proposed controller by Laplace transform technique and illustrate the improved control performance via an experiment for a ball and beam system.

• 한국산학기술학회논문지
• /
• 제14권12호
• /
• pp.6542-6549
• /
• 2013

콘크리트 구조물이 대형화됨에 따라 고교각, 장지간의 보 등 부재가 장대화되고 있으며, 장지간의 철근콘크리트 부재에서는 자중을 줄이고 강성을 증가시키기 위해 속빈 단면을 사용하는 것이 증가하는 추세이다. 본 연구에서는 철근콘크리트 속빈 단면 보의 모멘트-곡률 관계를 해석적 방법으로 구하여 속빈 부분의 크기, 상부플랜지와 복부의 철근 배치조건이 부재의 휨거동 및 곡률연성지수에 미치는 영향을 분석하였다. 속빈 부분의 크기($b_i/b_o$ 또는 $h_i/h_o$)가 0.5이하일 때에는 곡률연성지수가 일정하게 유지되며, 0.7이상이 되면 곡률연성지수가 급격히 감소하였다. 또한, 복부에 철근을 배치하면 곡률연성지수가 감소하며 단철근 보에서와 같은 수준의 연성지수를 얻기 위해서는 복부에 배치한 철근과 같은 양을 상부플랜지에 배치해야 하는 것으로 나타났다.