• 전기학회논문지
• /
• 제65권4호
• /
• pp.617-621
• /
• 2016

In addition to the energy storage facilities based on high power technologies, Electric double layer capacitors(EDLC) are today's candidate for power quality stabilization. However, its low energy density is often inhibiting factor for application of electric power industry. Hybrid supercapacitor is an promising energy storage device that positioned between conventional EDLC and Li-ion battery. This paper describes the preparation and characteristics of a hybrid supercapacitor and module for power quality stabilization. A cylindrical 3200F hybrid supercapacitor ($60{\times}74.5mm$) was assembled by using the $Li_4Ti_5O_{12}$ electrode as an anode and activated carbon as a cathode. It shows 2.5 times higher energy density than conventional EDLC with the same volume. In order to determine the characteristics of the hybrid supercapacitor Module for uninterruptible power supply (UPS), hybrid supercapacitor cells were connected in series with active balancing circuit. At even the high current density of 14A(10C), Module prepared by 18 cells showed the capacitance of 170F at 30~50V, suggesting the applicability for UPS.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.55-57
• /
• 2002

In industry, A pallet truck is drived mainly by d.c motor, because it use to battery for input power. However, d.c motor has a brush, this is the disadvantage of the d.c motor for a pallet truck. Though a brushless d.c motor has a permanent magnet, it is for low torque. Switched reluctance motors(SRM) have the advantage a high torque/weight ratio, as the large reluctance torque is made by salient poles of both start and rotor, and a high reliability, this paper design the shape of the switched reluctance motor that will replace a d.c motor for A pallet truck. First of all, designed parameter of SRM, outer diameter, diameter of rotor and stock length, from the outputr equation considering electric loading and magnetic loading. Next, design diameter of stator and rotor, depth of slot pole width, air gap as inner size of motor. The design of SRM certify the torque, the efficiency and the output power by a simulation.

• 한국정밀공학회지
• /
• 제27권10호
• /
• pp.34-39
• /
• 2010

We developed a path algorithm for ultrafast/wide area laser processing. Demands for high precision laser processing with a wide area has been increasing for a number of applications such as in solar cell battery, display parts, electronic component and automobile industry. Expansion of the area in which laser processing is an important factor to handle the ultrafast/wide area processing, it will require a processing path. Processing path is path of 2- axis stage and stage of change in velocity can be smooth as possible. In this paper, we proposed a smoothingnurbs method of improved speed profile. This method creates soft path from edge part, it is main purpose that scan area ($50mm{\times}50mm$) inside processing path makes path of topology of possible straight line. We developed a simulation tool using Visual C++.

• 한국정밀공학회지
• /
• 제29권6호
• /
• pp.640-647
• /
• 2012

Current electronic products are dominated by the laser processing and the application will be extended this time. Especially, demands for high precision laser processing with a large area has been increasing for a number of applications such as in solar cell battery, display parts, electronic component and automobile industry. In this paper we designed an on-the-fly system for ultrafast/high precision/large area laser processing. In addition, we have developed the path algorithm for large area. Expansion of the area in which laser processing is an important factor to handle the ultrafast/wide area processing, it will require a processing path. Processing path is path of 2- axis stage and stage of change in velocity can be smooth as possible. We proposed a path of the user concept using NURBS(Non-Uniform Rational B-Spline)method. Through our experiment with the chopper, was to prove the continuity of edge parts. Through basic shape experiments, we proved that large area can be processed using laser. We developed a simulation tool using Visual C++.

• 소성∙가공
• /
• 제17권8호
• /
• pp.657-661
• /
• 2008

Recently, products of electronic industry and related parts are required to have the thickness thinner and thinner to reduce the part weight. To go with this trend, LGP(light guide plate) of LCD-BLU(Liquid Crystal Display-Back Light Unit: It is one of kernel parts of LCD) for cell phone has the thickness of ${\sim}0.3mm$ and the battery case of cell phone has ${\sim}0.25mm$. Accordingly, high speed injection molding is required to mold products which have thinner parts. To achieve high speed injection and proper control of hydraulic unit, various design was applied to conventional injection unit. In the present paper, we concentrated on the molding stability of hydro-mechanical high speed injection machine to make an LGP of 0.3mm thickness.

• 전기학회논문지
• /
• 제56권11호
• /
• pp.1879-1884
• /
• 2007

In the electric power industry, it is important that the supply of energy must be guaranteed. Many power utilities control and supervise the transmission line to avoid power failures. In case of underground tunnel, some troubles are reported in cable joint. To stabilize the power, it is needed to monitor the cable joint. Many researches of cable joint monitoring have been going on by partial discharge measurement and temperature measurement using optical cable. These methods need much cost to install and maintain, so it is only used in critical transmission line. In this research, we use wireless sensor technology, because of its low cost and easy installation. We develop the temperature monitoring system for cable joint. Temperature sensor is installed on the surface of cable joint and sends data to server through router node using wireless network. Generally Ad hoc routing is searched in wireless network. However, in this research, we design the static linear routing mechanism, which is suitable for electric power line monitoring and analyze the life time of the sensor node by measuring the amount of the battery consumption.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.46-46
• /
• 2007

There has been rapid progress in the portable electronics industry. which has led to a great increase for a demand of portable, lightweight power sources. Lithium 2'nd batteries have met these demand. and many studies on the cahtod materials for the lithium 2,nd batteries have been reported during the last decade. Possible candidates for the cathode materials for lithium 2,nd batteries are $LiCoO_2$, $LiNiO_2$, and $LiMn_2O_4$. Currently $LiCoO_2$ is widely used. but $LiMn_2O_4$ is an excellent alternative material in view of its several advantages such a low cost as well as the wasy availability of raw materials and environmental benignity. In this study, find the most suitable synthesis method that satisfied high capacitor and stability cycle character, etc in Li-Mn oxide for 2'nd batteries. And also made an experiment on doping the $LiMn_2O_4$ spinel with a small amount of metal ions has a remarkable effect on the electrochemical properties and characterics of powder, BET, PSA, Porosity, etc.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1534-1536
• /
• 2005

A DC-DC converter is being widely used for various household appliances and for industry applications. The DC-DC converter is powered from single battery, and the voltage is varied according to the purpose. In the vehicle, various accessories whose electric power is different are being used. Thus, plural number of DC-DC converter should be provided, so these situations bring complicated circuits, and accordingly, higher cost. Under such backgrounds, in this paper, we propose a novel buck-boost chopper circuit with simply configuration which can supply to two or more different output loads. The propose chewer circuit can control output voltages by controlling duty ratio by using typically two switching devices, which is composed by single boost-switch and single buck-switch. The output voltage can be controlled widely. A few modified circuits developed from the fundamental circuit are represented including the general multi-load circuit. And all this merits and appropriateness was proved by computer simulation and experience.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.58-64
• /
• 2013

Several joining methods involving resistance welding, laser welding, ultrasonic welding and mechanical joining are currently applied in manufacturing lithium-ion batteries. Cu and Al alloys are used for tab and bus bar materials, and laser welding characteristics for these alloys were investigated with similar and dissimilar material combinations in this study. The base materials used were Al 1050 and oxygen-free Cu 1020P alloys, and a disk laser was used with a continuous wave mode. In bead-on-plate welding of both alloys, the joint strength was higher than the strength of O tempered base material. In overlap welding, the effect of welding parameters on the tensile shear strength and bead shape was evaluated. Tensile shear strength of overlap welded joint was affected by interfacial bead width and weld defect formation. The tensile-shear specimen was fractured at the heat affected zone by selecting proper laser welding parameters.

• Nuclear Engineering and Technology
• /
• 제51권3호
• /
• pp.676-682
• /
• 2019

After the Fukushima Daiichi accident, there has been an increasing preference for passive safety features in the nuclear power industry. Some passive safety systems require limited active components to trigger subsequent passive operation. Under very serious accident conditions, passive safety features could be rendered inoperable or damaged. This study evaluates (i) the performance and effectiveness of the passive safety features of iPOWER (innovative Power Reactor), and (ii) whether a severe accident condition could be reached if the passive safety systems are damaged, namely the case of heat exchanger tube rupture. Analysis results show that the reactor coolant system remains in the hot shutdown condition without operator actions or electricity for over 72 h when the passive auxiliary feedwater systems (PAFSs) are operable without damage. However, heat exchanger tube rupture in the PAFS leads to core damage after about 18 h. Such results demonstrate that, to enhance the safety of iPOWER, maintaining the integrity of the PAFS is critical, and therefore additional protections for PAFS are necessary. To improve the reliability of iPOWER, additional battery sets are necessary for the passive safety systems using limited active components for accident mitigation under such extreme circumstances.