• Journal of Electrical Engineering and Technology
• /
• v.11 no.4
• /
• pp.860-868
• /
• 2016

A bidirectional DC-DC converter (BDC) is an indispensable electrical unit for the electric vehicles (EVs). High efficiency, high power density, isolation, light weight and reliability are all essential requirements for BDC. In this paper, a 3 kW BDC for the battery charger of EVs is proposed. The proposed converter consists of a half-bridge structure on the primary side and an isolation transformer and a synchronous rectifier structure on the secondary side. With this topology, minimum number of switching devices are required for bidirectional power flow between the two dc buses of EVs. The easy implementation of the synchronous rectification gives advantages in terms of efficiency, cost and flexibility. The proposed BDC achieves high efficiency when operating in both modes (step-up and step-down). A 3 kW prototype is implemented to verify theoretical analysis and the performance of the proposed converter.

• Journal of Electrochemical Science and Technology
• /
• v.3 no.1
• /
• pp.14-23
• /
• 2012

Increasing demand of energy, the depletion of fossil fuel reserves, energy security and the climate change have forced us to look upon alternate energy resources. For today's electric vehicles that run on lithium-ion batteries, one of the biggest downsides is the limited range between recharging. Over the past several years, researchers have been working on lithium-air battery. These batteries could significantly increase the range of electric vehicles due to their high energy density, which could theoretically be equal to the energy density of gasoline. Li-air batteries are potentially viable ultra-high energy density chemical power sources, which could potentially offer specific energies up to 3000 $Whkg^{-1}$ being rechargeable. This paper provides a review on Lithium air battery as alternate energy resource for the future.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.394-402
• /
• 2019

This paper proposes a single-phase non-isolated onboard battery charger (OBC) for electric vehicles (EVs) that only uses small film capacitors at the DC-link of the AC-DC converter. In the proposed charger, an isolated DC-DC converter for low-voltage batteries is used as an active power decoupling (APD) circuit to absorb the ripple power when a high-voltage (HV) battery is charged. As a result, the DC-link capacitance in the AC-DC converter of the HV charging circuit can be significantly reduced without requiring any additional devices. In addition, some of the components of the proposed circuit are shared in common for the different operating modes among the AC-DC converter, LV charging circuit and active power filter. Therefore, the cost and volume of the onboard battery charger can be reduced. The effectiveness of the proposed topology has been verified by the simulation and experimental results.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.3
• /
• pp.236-241
• /
• 2024

Due to the recent emphasis on carbon neutrality and environmental regulations, the global electric vehicle (EV) market is experiencing rapid growth. This surge has raised concerns about the recycling and disposal methods for EV batteries. Unlike traditional internal combustion engine vehicles, EVs require unique and safe methods for the recovery and disposal of their batteries. In this process, predicting the lifespan of the battery is essential. Impedance and State of Charge (SOC) analysis are commonly used methods for this purpose. However, predicting the lifespan of batteries with complex chemical characteristics through electrical measurements presents significant challenges. To enhance the accuracy and precision of existing measurement methods, this paper proposes using a Long Short-Term Memory (LSTM) model, a type of deep learning-based recurrent neural network, to diagnose battery performance. The goal is to achieve safe classification through this model. The designed structure was evaluated, yielding results with a Mean Absolute Error (MAE) of 0.8451, a Root Mean Square Error (RMSE) of 1.3448, and an accuracy of 0.984, demonstrating excellent performance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.1
• /
• pp.74-79
• /
• 2022

This paper proposes a DC-DC converter that satisfies a wide output voltage of 150 V-1000 V for the battery voltage of various electric vehicles and can be controlled in both directions for the demand resource of electric vehicles. The proposed converter is a two-stage structure in which an insulated converter and a non-isolated converter are combined and operates as constant current or constant power depending on the voltage of the connected battery. Experimental results from a 20 kW prototype are provided to validate the proposed charger, and a maximum efficiency of 97% is obtained.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.5
• /
• pp.373-381
• /
• 2017

The electric vehicle market has increased rapidly in recent years. Established global automakers have announced that electric cars will be developed and distributed. Furthermore, current electric cars are not merely breezes, instead, they are the mainstream of automobiles. However, high prices, short mileage, and long charge times are the main obstacles to the spread of electric vehicles. To solve these problems, the competition for technology development for the expansion of electric vehicles worldwide intensifies because of the improvements in mileage, price reduction, and expansion of charging infrastructure. In this paper, the trends in the development of key technologies for electric vehicles in overseas markets and the present strategic goals for the development of key technologies for electric vehicles in Korea will be identified.

• International Journal of Internet, Broadcasting and Communication
• /
• v.14 no.2
• /
• pp.129-135
• /
• 2022

Currently, the rapid growth of electric vehicles and the collection and disposal of waste batteries are becoming a social problem. The purpose of this paper is to propose a fast and efficient battery screening method through a safe inspection and storage method according to the collection and storage of waste batteries of electric vehicles. In addition, as the resistance inside the waste battery increases, an instantaneous voltage drop occurs, and there is a risk of overcharging and overdischarging compared to the initial state of the battery. Accordingly, there are great difficulties in operation, so the final goal of this study is to develop a device for diagnosing aging through real-time battery internal resistance measurement. Final result As a result of simulation of the internal resistance measurement test circuit through external impedance (AC), the actual simulation value was 0.05Ω, RS = Vrms / Irms => Vrms = 8.0036mV, Irms = 162.83Ma. Substitute the suggested method. The result was calculated as Rs = 0.0495Ω. It is possible to measure up to 64 impedances inside the aging diagnostic equipment that enables real-time monitoring of the developed battery cells, and the range can be changed according to the application method.

• International Journal of Internet, Broadcasting and Communication
• /
• v.15 no.3
• /
• pp.129-134
• /
• 2023

Although the use of batteries is rapidly increasing worldwide to improve carbon neutrality and energy efficiency, performance degradation due to the increase in the number of uses is inevitable as it is a finite resource that can be applied according to capacity and specifications. Deterioration and failure of batteries are recognized as important problems in various applications using batteries, including electric vehicles. In order to solve these problems, a diagnostic technology capable of accurately predicting battery life and grasping state information is required, but it is difficult in a non-linear form due to internal structure or chemical change. In this paper, the factors that generally cause battery performance change are directly applied to check whether there are external changes and impedance changes in the battery, and to analyze whether they affect battery life. Impedance change trends and result values were confirmed using a universal impedance spectroscopy method and a self-developed internal impedance measurement method. The results did not significantly affect the impedance change trend. It was confirmed that the increase in the number of times of battery use was prominent in the impedance change trend.

• International journal of advanced smart convergence
• /
• v.11 no.3
• /
• pp.222-228
• /
• 2022

As a means to cope with the climate change crisis caused by global warming, automobile manufacturers continue to make efforts to use the driving energy of vehicles as electricity. As a result, parts industry such as battery, motor, and controller are attracting attention. China is often seen in large cities, with electric vehicles such as electric bicycles, electric motorcycles, and small electric vehicles popularized and commercialized, mainly in large cities. However, small electric vehicles are not popular in Korea, which is why the country's topography is high in hills. In order to drive the hilly domestic roads, power performance including vehicle climbing ability should be improved. In order to improve the power performance and the climbing capacity of small electric vehicles, the capacity of the motor should be increased. However, when the performance of the motor is improved, the weight of the motor becomes heavy and the price competitiveness is likely to decrease. In addition, in order to operate a high-performance motor, the power consumption of the battery is rapidly increased, so various problems must be solved. In order to commercialize a small electric vehicle for one or two people who do not emit harmful exhaust gas to the human body in a hilly domestic terrain, it is effective to have a separate transmission system. In this study, we were conducted dynamometer test to produce a continuously variable transmission(CVT) system prototype using a spring that can be applied to a small electric vehicle and to install a CVT system prototype manufactured in a small electric vehicle. The dynamometer test results showed that the maximum speed performance, acceleration performance, and climbing performance were improved.

• Corrosion Science and Technology
• /
• v.21 no.5
• /
• pp.348-359
• /
• 2022

Interest in electric vehicle is on the rise due to global eco-friendly policies. To improve the efficiency of electric vehicles, it is essential to reduce weights of components. Since electric vehicles have various electronic equipment, the research on stray current corrosion is required. In this research, a galvanostatic corrosion experiment was performed on 6061-T6 Al alloy for electric vehicle battery housing using chloride concentration and applied current density as variables in a solution simulating an acid rain environment. As a result of the experiment, when chloride concentration and applied current density were increased, corrosion damage became larger. In particular, pitting damage was dominant at an applied current density of 0.1 mA/cm². Pitting damage over the entire surface was found at a current density of 1.0 mA/cm². In conclusion, chloride concentration had a relatively large effect on localized corrosion. The applied current density had a great effect on uniform corrosion. However, in the case of applied current density, localized corrosion was also greatly affected by interaction with chloride.