• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.1
• /
• pp.105-113
• /
• 2000

Seismic behavior of 3-dimensional setback structures showing abrupt reductions of the floor size within the structure height and the effect of in-plane deformations of floor slabs on the seismic behavior of those structures are investigated. To find out general seismic behavior of 3-dimensional setback structures two parameters, level of setback(L/sub s/) and degree of setback(R/sub s/) are used. Analysis results obtained from forty eight setback structures show that a sudden change in story shear near setback level is occurred for irregular setback structures. The effect of in-plane deformation of floor slabs on the seismic behavior of setback structures is greatly influenced by the arrangement of lateral load resisting elements and it is more pronounced for frame-shear wall system showing large difference in stiffness among the lateral load resisting elements. The in-plane deformation of floor slabs results in reduced base shear, especially for FW-type structures with L/sub s/=1.0. Also, it brings about reduced story shear for the lateral load resisting element with shear wall and increase in story shear lot the lateral load resisting element without shear wall. The in-plane deformation of floor slabs at the base portion and/or tower portion due to difference in stiffness among the lateral load resisting elements brings about increment of floor displacements at all floor level.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.8
• /
• pp.2637-2649
• /
• 1996

Flow characteristics and aerodynamic forces acting on an elliptic cylinder placed in a plane boundary layer were investigated experimentally. Four cylinder models with axis ratio(major axis to minor axis, AR=A/B) of 1, 2, 3, and 4 having the same equivalent diameter were used in this experiment. The Reynolds number based on the equivalent diameter $D_e$(=20mm) was 13,000. In the case of circular cylinder, regular vortex shedding occurs for the cylinder gaps larger than G/B=0.3 and is not almost related to the boundary layer thickness. But, for the elliptic cylinders, the vortex shedding frequency is increased with increasing the gap ratio (G/B) and the axis ratio (AR) of elliptic cylinders. The maximum drag coefficient acting on a circular cylinder is mainly affected by the boundary layer thickness. But, the elliptic cylinders(AR$\geq$2), except for the smaller gap G/B<0.2, show a nearly constant drag coefficient which is much smaller than that of a circular cylinder. The base pressure on the flat plate decreases with increasing the axis ratio(AR) of the elliptic cylinder. In the case of a circular cylinder, the base pressure has the minimum value at the gap ratio G/B=0.4, but it occurs at G/D=2 for elliptic cylinders. The mean velocity of the cylinder wake is quickly recovered at a small cylinder height ratio(H/$\delta$), but the turbulent intensity is rapidly recovered at a large cylinder height ratio(H/$\delta$). The effective wake region in the plane boundary layer is shrinkaged with increasing the axis ratio(AR) of elliptic cylinder. And the drag coefficient and streamwise turbulent intensity of the elliptic cylinder with AR=4 are less than half of those for the circular cylinder(AR=1).

• Journal of Yeungnam Medical Science
• /
• v.8 no.1
• /
• pp.32-41
• /
• 1991

This study was made to investigate the effect of adenoidectomy on dentofacial skeleton in naso-respiratory dysfunction children. The clinical material compromised the 24 children in a previous study who had naso-respiratory dysfunction and 24 children who were the nasal breathing with normal occlusion. The cephalograms were taken at the initial examination and 1 year later for the control group and experimental group the paired sample statistical analysis was performed. The result were as follows. 1. In cranial base variable, difference between two groups were not statistically significant. 2. In craniofacial variable, experimental group showed brachyfacial pattern but control groups didn't show significant growth pattern. 3. In maxillary variables, experimental group showed flattening the palptal plane. 4. In mandibular variables, experimental group showed the decrease of mandibular plane angle and gonial angle. 5. In facial height variables, experimental group showed horizontal growth rotation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.10
• /
• pp.1261-1268
• /
• 2019

In this paper, we present the analysis of a novel monopole antenna with a reflector. The proposed monopole antenna is printed on a TRF-45 substrate, and the reflector, which is positioned near the base of the antenna, is printed on the FR-4 substrate. Positioning the reflector near the base of the antenna was found to suppress current radiation toward the back of the monopole antenna. Comparative analysis of the proposed monopole antenna and a conventional monopole antenna without a reflector revealed that the bandwidths of the antenna with and without a reflector were 2.65 GHz and 2.88 GHz, respectively. Additionally, the antenna without a reflector was observed to have a bi-directional radiation pattern in the E-plane, and an omni-directional radiation pattern in the H-plane. However, only the antenna with a reflector was found to suppress back radiation, and provide non-uniform directional radiation in the E-plane and H-plane.

• Journal of the Korean Vacuum Society
• /
• v.20 no.2
• /
• pp.141-145
• /
• 2011

ZnO:Al thin films were deposited by RF magnetron sputtering with various base pressure, and their structural, optical, and electrical properties were studied. The influence of the base pressure on the ZnO:Al thin film was confirmed and a high-quality thin film was obtained by controlling the base pressure. In all Al-doped ZnO thin films, the preferred orientation of (002) plane was observed and light transmittance in visible region (400 nm~800 nm) had above 85%. With decreasing of base pressure, crystallinity, resistivity, and figure of merit were improved. The improvement of resistivity with base pressure was attributed to the change of grain size.

• Education of Primary School Mathematics
• /
• v.19 no.4
• /
• pp.291-311
• /
• 2016

Researcher was interested in circumference of plane figure problem. Meanwhile, researcher found some difficulty in solving circumference problem with stair like plane figure. In this phenomenon, researcher felt to find the teaching method to help students with circumference of plane figure. For this, researcher analyzed many students' recording paper and had interview with few students. As a result researcher found that students had some difficulty in recognizing essential information and prior knowledge base was not made up. From these responses, this paper proposed teaching method for helping students about circumference related problems.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3615-3620
• /
• 2013

Two novel copper(II) bromide complexes with pyridine containing Schiff base ligands, $Cu(pmed)Br_2$ and $Cu(pmed)Br_2$ where pmed = N'-((pyridin-2-yl)methylene)ethane-1,2-diamine (pmed) and dpmed = N,N-diethyl-N'-((pyridin-2-yl)methylene)ethane-1,2-diamine (dpmed) were synthesized and characterized using X-ray single crystal structure analysis, optical and magnetic susceptibility measurements. Crystal structural analysis of $Cu(pmed)Br_2$ showed that the copper(II) ion has a distorted square-pyramidal geometry with the trigonality index of ${\tau}=0.35$ and two intermolecular hydrogen bonds, which result in the formation of two dimensional networks in the ab plane. On the other hand, $Cu(pmed)Br_2$ displayed a near square-pyramidal geometry with the value of ${\tau}=0.06$. In both compounds, the NNN Schiff base and one Br atom occupy the basal plane, whereas the fifth apical position is occupied by the other Br atom at a greater Cu-Br apical distance. The reported complexes show $g_{\mid}$ > $g_{\perp}$ > 2.0023 with a $d_{x2-y2}$ ground state and a penta-coordinated square pyramidal geometry. Variable temperature magnetic susceptibility measurements showed that the developed copper(II) complexes follow the Curie-Weiss law, that is there are no magnetic interactions between the copper(II) ions since the Cu--Cu distance is too far for magnetic contact.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1451-1459
• /
• 1995

The objective of this paper is to evaluate the material properties of SA312 TP316 and SA312 TP304 stainless steels and their associated welds manufactured for safety injection system of Yonggwang 3,4 nuclear generating stations. A total of 62 tensile tests and 46 fracture toughness tests were conducted and the effects of various parameters such as pipe size, crack plane orientation, tests were conducted and the effects of various parameters such as pipe size, crack plane orientation, test temperature, welding on material properties were discussed. Test results show that the effect of test temperature on fracture toughness was significant while the effects of pipe size and crack plane orientation on fracture toughness were negligible. Fracture toughness of the weld metal was in general higher than that of the base metal.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.3
• /
• pp.225-230
• /
• 2016

Since the development of anodic aluminum oxide (AAO), extensive studies have been conducted ranging from fundamental research to the applications of AAO. Most of the research on AAO structures have focused on well-aligned nanoporous structures fabricated under specific conditions. This study investigated fabricable AAO structures with anodization performed with various temperatures, electrical potentials, and basal plane surfaces. As a result, nanoporous and nanofibrous structures were fabricated. The nanopores were formed at a relatively lower temperature and potential, and the nanofibers were formed at a relatively higher temperature and potential regardless of the basal plane surface. The shape of the base surface was found to influence the structural arrangement in nanoporous morphologies. These interesting findings relating to new morphologies have the potential to broaden the possible applications of AAO materials.

• Applied Microscopy
• /
• v.27 no.2
• /
• pp.111-120
• /
• 1997

Cylinder-like crystals of $Ca^{2+}-ATPase$ provide views parallel to the lamellar plane, from which parameters of lamellar stacking can be directly measured. These parameters were measured using different preparation methods. Assuming that molecular packing is the same, data from lamellar plane could supplement those obtained by tilting large, thin plate-like crystals. However, base on data obtained .by electron microscopy and x-ray powder patterns, the plate-like crystal may have another scheme for stacking the lamellar. The projection map (h, 0, 1) from cylinder-like crystals using cryoelectron microscopy suggest the lamellar spacing can be variable.