• Journal of KIISE:Databases
• /
• v.28 no.3
• /
• pp.458-467
• /
• 2001

Optimistic Two-Phase Locking(O2PL) performs as well as or better than the other approaches because it exploits client caching well and also has relatively lower network bandwidth requirements. However, O2PL leads to unnecessary waits, because, it can not be commit a transaction until the transaction obtains all requested locks. In addition, Optimistic Concurrency Control(OCC) tends to make needless aborts. This paper suggests an efficient optimistic cache consistency protocol that overcomes such shortcomings. Our scheme decides whether to commit or abort a transaction without wait and it adopts transaction re-ordering in order to minimize the abort rate. Our scheme needs only one version for each data item in spite of the re-ordering mechanism used. Finally, this paper presents a simulation-based analysis that shows superiority in performance of out scheme to O2PL and OCC.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.362-373
• /
• 2016

The on-line measurement of high-power IGBT collector current is important for the hierarchical control and short-circuit and overcurrent protection of its driver and the sensorless control of the converter. The conventional on-line measurement methods for IGBT collector current are not suitable for engineering measurement due to their large-size, high-cost, low-efficiency sensors, current transformers or dividers, etc. Based on the gate driver, this paper has proposed a current measuring circuit for IGBT collector current. The circuit is used to conduct non-intervention on-line measurement of IGBT collector current by detecting the voltage drop of the IGBT power emitter and the auxiliary emitter terminals. A theoretical analysis verifies the feasibility of this circuit. The circuit adopts an operational amplifier for impedance isolation to prevent the measuring circuit from affecting the dynamic performance of the IGBT. Due to using the scheme for integration first and amplification afterwards, the difficult problem of achieving high accuracy in the transient-state and on-state measurement of the voltage between the terminals of IGBT power emitter and the auxiliary emitter (u_Ee) has been solved. This is impossible for a conventional detector. On this basis, the adoption of a two-stage operational amplifier can better meet the requirements of high bandwidth measurement under the conditions of a small signal with a large gain. Finally, various experiments have been carried out under the conditions of several typical loads (resistance-inductance load, resistance load and inductance load), different IGBT junction temperatures, soft short-circuits and hard short-circuits for the on-line measurement of IGBT collector current. This is aided by the capacitor voltage which is the integration result of the voltage uEe. The results show that the proposed method of measuring IGBT collector current is feasible and effective.

• The KIPS Transactions:PartA
• /
• v.13A no.3 s.100
• /
• pp.223-230
• /
• 2006

A MMORPG(Massively Multiplayer Online Role-Playing Game) is an online role-playing game in which a large number of players can interact with each other in the same world at the same time. Most of them require significant hardware requirements(e.g., servers and bandwidth), and dedicated support staff. Despite the efforts of developers, users often cite overpopulation, lag, and poor support as problems of games. In this paper, a dynamic load balancing method for MMORPGS is proposed. It tries to adapt to dynamic change of population by using dynamic map-partition method with VML(Virtual Map Layer) which consists of fields, sector groups, sectors, and cells. From the experimental results, our approach achieves about $23^{\sim}67%$ lower loads for each field server. By the modification to Virtual Area Layer, we can easily manage problems that come from changes of map data, resources' status, and users' behavior pattern.

• The KIPS Transactions:PartA
• /
• v.8A no.4
• /
• pp.419-428
• /
• 2001

Advances in circuit and integration technology are continuously boosting the speed of processors. One of the main challenges presented by such developments is the effective use of powerful processors in shared memory multiprocessor system. We believe that the interconnection problem is not solved even for small scale shared memory multiprocessor, since the speed of shared buses is unlikely to keep up with the bandwidth requirements of new powerful processors. In the past few years, point-to-point unidirectional connection have emerged as a very promising interconnection technology. The single slotted ring is the simplest form point-to-point interconnection. The main limitation of the single slotted ring architecture is that latency of access increase linearly with the number of the processors in the ring. Because of this, we proposed the dual slotted ring as an alternative to single slotted ring for cache-based multiprocessor system. In this paper, we analyze the proposed dual slotted ring architecture using new snooping protocol and enforce simulation to compare it with single slotted ring.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.10
• /
• pp.983-990
• /
• 2010

Reduction of acoustic loads of space launch vehicles can be achieved by acoustic absorbers satisfying strict cleanness requirements. This limited the use of general porous materials and requires non-porous sound absorbers. Micro-perforated panel absorbers(MPPA) is one of promising sound absorbers satisfying the cleanness requirement for launch vehicles. However, its applicability was limited to low sound pressure levels according to the acoustic impedance model of micro-perforated panels. In this paper the applicability of micro-perforated panel absorbers at high incident sound pressure was investigated in experimental ways. The absorption characteristics of a micro-perforated panel absorber was simulated according to its design variables, e.g., minute hole diameters and aperture ratios. It was shown that optimal design can be readily done by using proposed design charts. Experiments were conducted to measure acoustic properties of the designed micro-perforated panel absorbers. The results showed that acoustic resistance increases rapidly as incident sound pressure level does but change of acoustic reactance can be neglected in a practical point of view. This caused the decrease of peak value of absorption coefficient at high incident sound pressure level, but the amount of reduction can be accepted in practice. The major advantage of the micro-perforated panel absorber(wide absorption bandwidth) was still kept at high sound pressure level.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.11
• /
• pp.4515-4521
• /
• 2010

A Yagi antenna, which is a typical directional antenna, has been designed and fabricated as a surveillance sensor. The proposed Yagi antenna satisfies the requirements as a surveillance sensor; impedance bandwidth of 7.2-8.2GHz, maximum gain of 7dBi, and 3dB beamwidth of $60^{\circ}$ in the azimuthal plane. The proposed Yagi antenna is designed with 3 directors and one driven element on a dielectric substrate. Also, a microstrip-to-CPS balun is designed and applied to the proposed antenna for balanced feeding of the dirven element. The performance of the proposed antenna has been verified by comparing the simulation and measurement results.

• Journal of Korea Multimedia Society
• /
• v.7 no.5
• /
• pp.698-712
• /
• 2004

DiffServ network architecture does not define a call admission control procedure explicitly. In this paper, a new DiffServ QoS control mechanism is suggested which, after the call admission control, can execute packet process according to the class while, at the same time, executing on the flow based call admission control in the DiffServ network. Routers on the path from the source to the destination estimate the aggregated class traffic of the existing flows and the new incoming flow and then, perform a call admission control in accordance with the type of classes efficiently based on the required bandwidth per each class that can meet the user's QoS requirements. In order to facilitate the packet process according to the class after the flow based call admission control, a mechanism is suggested that can adjust the network resources to classes dynamically. The performance analysis on this mechanism is carried out through a simulation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.780-783
• /
• 2009

The application of MOST150 technology has been required to satisfy the demand for the automotive infotainment system and the higher bandwidth requirements caused by the increase of the multimedia processing capacity. The Ethernet technology applied gateway was implemented for an efficient transmission of multimedia, a vehicle diagnosis, an external communication, a data processing between the MOST150 and the CAN communication method applied to many existing vehicles. The new algorithm and application were suggested in order to efficiently perform the data processing between other types of communication systems. The existing MOST150 frame is mainly composed of the Control Channel, the Legacy Packet Channel(async) and the Synchronous /Isochronous Channels and performs the data processing through these sequential channels. With the sense of this process, this study suggested the new algorithm that the Mapping method of the IETF's QoS Management was applied to the MOST150 technology for the efficient QoS.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.2
• /
• pp.13-21
• /
• 2012

Mobile data caching is usually used as an effective way to improve the speed of local transaction processing and reduce server load. In mobile database environment, due to its characters - low bandwidth, excessive latency and intermittent network, caching is especially crucial. A lot of mobile data caching strategies have been proposed to handle these problems over the last few years. However, with smart phone widely application these approaches cannot support vast data requirements efficiently. In this paper, to make full use of cache data, lower wireless transmission quantity and raise transaction success rate, we design a new mobile data caching synchronization strategy based on in-demand and replacement priority. We experimentally verify that our techniques significantly reduce quantity of wireless transmission and improve transaction success rate, especially when mobile client request a large amount of data.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.32 no.3
• /
• pp.565-573
• /
• 2022

Current mobile communication system is in the mid-process of conversion from 4G LTE to 5G network. According to the generalization of mobile communication services, personal information such as user's identifiers and location information is transmitted through a mobile communication network. The importance of security technology is growing according to the characteristics of wireless mobile communication networks, the use of wireless shared channels is inevitable, and security technology cannot be applied to all network system elements in order to satisfy the bandwidth and speed requirements. In particular, for security threat analysis, researches are being conducted on various attack types and vulnerability analysis through rogue base stations or attacker UE to make user services impossible in the case of 5G networks. In this paper, we established a 5G network testbed using open sources. And we analyzed three security vulnerabilities related to NAS COUNT and confirmed the validity of two vulnerabilities based on the testbed or analyzing the 3GPP standard.