• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.366-367
• /
• 2005

The effect of benzotriazole (BTA) on the adhesion force of silica and pad particle on Cu/TEOS wafer surfaces was investigated with and without the addition of BTA. Cu-BTA had the isoelectric point (IEP) at around pH 4$\sim$8. Pad particles were more positive zeta potentials than silica. The adhesion force initially decreased of silica and pad particle on Cu surfaces when BTA was added. However, the more BTA was added, the more adhesion force gradually increased with the increase of BTA concentrations. Then the adhesion force of pad particle was higher than silica. And TEOS didn't resulted increasing adhesion force like Cu when BTA was added in DI water.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.42-43
• /
• 2005

본 연구에서는 Cu 슬러리에 부식방지제인 BTA를 첨가하여 슬러리내의 과수의 농도, pH 의 변화, 연마입자의 종류에 따라 연마거동에 미치는 영향과 각 chemical 변화에 따른 Cu surface의 변화를 살펴보았다. BTA (Benzotriazole, $C_6H_4C_3H$)를 첨가함으로써 본 연구에서 시행된 pH 와 과수의 변화에 상관없이 Cu-BTA film을 형성하여 Cu의 dissolution을 최대한 억제하는 것을 확인할 수 있었다. 또 그로인해 BTA를 첨가하지 않았을 때보다 얇은 passivation layer를 형성함을 알 수 있었고 contact angle도 더 높았다. 연마율의 경우에도 BTA가 첨가됨으로써 감소됨을 확인할 수 있었고 연마입자로 alumina particle을 사용한 경우에는 pH6, 과수 10vol%이상에서는 오히려 연마율이 증가하였다. fumed silica의 경우에는 hardness가 작아 mechanical적인 제거력이 낮아 BTA가 첨가되어도 연마율에는 큰 영향이 없었다.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2014년도 추계학술대회
• /
• pp.288-290
• /
• 2014

본 논문에서는 MIPI(Mobile Industry Processor Interface) DSI(Display Serial Interface) 규격을 지원하는 마스터 브릿지 IC의 Escape 모드와 BTA(Bus Turn Around) 모드를 구현하였다. MIPI DSI 마스터 브릿지 IC는 RGB 데이터 및 각종 제어 명령어를 디스플레이 모듈(슬레이브)로 전송하여 디스플레이 모듈을 시험하는 용도로 사용된다. 슬레이브로 저속 명령어 전송을 위한 저전력 패킷전송(LPDT), 초저전력상태(ULPS) 전송, 트리거 메시지 전송을 위한 Escape 모드를 구현하였다. 또한 BTA 모드를 통해 슬레이브로부터 데이터를 수신하여 디스플레이 모듈의 정보를 얻는 버스 방향전환 동작을 구현하였다. 설계된 Escape 및 BTA 기능이 MIPI DSI 규격에서 정의되는 다양한 조건들에 대해 올바로 동작함을 기능검증을 통해 확인하였다.

• 한국정밀공학회지
• /
• 제15권9호
• /
• pp.43-49
• /
• 1998

The deep hole drilling has an increasing demands because of its wide range applications and its good productivity. The BTA drills are capable of machining for having a large length to diameter ratio in single pass to higher degree of accuracy and surface finish. It's really necessary that the investigation for the deep hole drilling by the BTA drill because its required quality should be satisfied with single pass. This thesis deal with the experimental results obtained during single tube BTA system machining on SM55C steel for different machining conditions. The results of the investigation on the optimum cutting condition selecting and tool life reveals as follows. (1) The optimum cutting condition was cutting speed, V = 42 m/min and feed speed. F = 90 mm/min and the tool life was about 10 meters. (2) Surface roughness was $12\mum$ and the roundness was less using $16mum$single edge BTA drill in testing cutting condition.

• Animal Bioscience
• /
• 제37권7호
• /
• pp.1156-1167
• /
• 2024

Objective: MicroRNAs (miRNAs) are endogenous non-coding RNAs that can play a role in the post-transcriptional regulation of mammalian preadipocyte differentiation. However, the precise functional mechanism of its regulation of fat metabolism is not fully understood. Methods: We identified bta-miR-365-3p, which specifically targets the 3' untranslated region (3'UTR) of the FK506-binding protein 5 (FKBP5), and verified its mechanisms for regulating expression and involvement in adipogenesis. Results: In this study, we found that the overexpression of bta-miR-365-3p significantly decreased the lipid accumulation and triglyceride content in the adipocytes. Compared to inhibiting bta-miR-36 5-3p group, overexpression of bta-miR-365-3p can inhibit the expression of adipocyte differentiation-related genes C/EBPα and PPARγ. The dual-luciferase reporter system further validated the targeting relationship between bta-miR-365-3p and FKBP5. FKBP5 mRNA and protein expression were detected by quantitative real-time polymerase chain reaction and Western blot. Overexpression of bta-miR-365-3p significantly down-regulated FKBP5 expression, while inhibition of bta-miR-365-3p showed the opposite, indicating that bta-miR-365-3p negatively regulates FKBP5. Adenosine 5'-monophosphate (AMP)-activated protein kinase/mammalian target of rapamycin (AMPK/mTOR) signaling pathway is closely related to the regulation of cell growth and is involved in the development of bovine adipocytes. In this study, overexpression of bta-miR-365-3p significantly inhibited mRNA and protein expression of AMPK, mTOR, and SREBP1 genes, while the inhibition of bta-miR-365-3p expression was contrary to these results. Overexpression of FKBP5 significantly upregulated AMPK, mTOR, and SREBP1 gene expression, while inhibition of FKBP5 expression was contrary to the above experimental results. Conclusion: In conclusion, these results indicate that bta-miR-365-3p may be involved in the AMPK/mTOR signaling pathway in regulating Yanbian yellow cattle preadipocytes differentiation by targeting the FKBP5 gene.

• 한국해양공학회지
• /
• 제8권1호
• /
• pp.131-143
• /
• 1994

The BTA(boring and trepanning association) deep hole machining has an increasing demands because of its wide applications and its good productivity. The main feature of the BTA tools is that the tool cutting edges are unsymmetrically located on the boring head. This provides a stabilizing cutting force resultant necessary for self guidance of the boring head. The BTA tools are capable of machining for having a large length to diameter ratio in single pass. A study of the accuracy and surface finish of holes produced would reveal quite useful information regarding the process. This study deals with the experimental results obtained during BTA machining on SM55C, SM45C steel under differnt machining conditions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.257-260
• /
• 1997

In order to investigate the volume resistivity on the electrical properties of transformer oils, the Transformer oils contained BTA is prepared, which was classified by the contents of BTA, such as 1[ppm], 10[ppm], 20[ppm], 30[ppm], 50[ppm], respectively. To measure the physical properties of transformer oils contained BTA, Fourier Transform Infrared Spectroscopy is investigated. And for the study of electrical properties is made by measuring the volume resistivity of each specimen. As result of this experiments, it is confirmed that the volume resistivity characteristics of specimen contained BTA 10[ppm] is superior.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.84-89
• /
• 1998

BTA drilling among the deep hole drilling is using for the improvement of productivity and the high-efficient working. As the deep hole drilling with BTA drill is satisfied with the required quality by one-pass processing, more deeper hole depth, the accuracy of materials is affected by bending vibration and cutting speed. This paper is studied that the shapes of material (surface roughness, roundness) is affected by cutting condition compared actual roundness with lobe shape with modeling of computer through the experiments in the BTA drilling system with BTA drill.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.267-269
• /
• 1997

The electrical properties due to the Benzotriazole(following as BTA) additive in fluids for insulating and cooling the ultra-high voltage transformer is studied in this paper. Specimen having the several contents of BTA, such as 5[ppm]. 10[ppm] and 30[ppm] is used in order to investigate the characteristics on volume resistivity in case of fluid flow in experimental device made in lab. Volume resistivity is decreased with an increase of fluid flow velocity and increased with BTA content in low temperature region, but volume resistivity of specimen contained BTA 10[ppm] is the largest thing over $30[^{\circ}C]{\sim}50[^{\circ}C]$ than the others in experiment.