• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.366-367
• /
• 2005

The effect of benzotriazole (BTA) on the adhesion force of silica and pad particle on Cu/TEOS wafer surfaces was investigated with and without the addition of BTA. Cu-BTA had the isoelectric point (IEP) at around pH 4$\sim$8. Pad particles were more positive zeta potentials than silica. The adhesion force initially decreased of silica and pad particle on Cu surfaces when BTA was added. However, the more BTA was added, the more adhesion force gradually increased with the increase of BTA concentrations. Then the adhesion force of pad particle was higher than silica. And TEOS didn't resulted increasing adhesion force like Cu when BTA was added in DI water.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.42-43
• /
• 2005

본 연구에서는 Cu 슬러리에 부식방지제인 BTA를 첨가하여 슬러리내의 과수의 농도, pH 의 변화, 연마입자의 종류에 따라 연마거동에 미치는 영향과 각 chemical 변화에 따른 Cu surface의 변화를 살펴보았다. BTA (Benzotriazole, $C_6H_4C_3H$)를 첨가함으로써 본 연구에서 시행된 pH 와 과수의 변화에 상관없이 Cu-BTA film을 형성하여 Cu의 dissolution을 최대한 억제하는 것을 확인할 수 있었다. 또 그로인해 BTA를 첨가하지 않았을 때보다 얇은 passivation layer를 형성함을 알 수 있었고 contact angle도 더 높았다. 연마율의 경우에도 BTA가 첨가됨으로써 감소됨을 확인할 수 있었고 연마입자로 alumina particle을 사용한 경우에는 pH6, 과수 10vol%이상에서는 오히려 연마율이 증가하였다. fumed silica의 경우에는 hardness가 작아 mechanical적인 제거력이 낮아 BTA가 첨가되어도 연마율에는 큰 영향이 없었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.288-290
• /
• 2014

In this paper, Escape and BTA(Bus Turn Around) modes of master bridge IC are implemented, which supports MIPI(Mobile Industry Processor Interface) DSI(Display Serial Interface) standard. MIPI DSI master bridge IC sends RGB data and various commands to display module(slave) in order to test it. The Escape mode is designed to implement LPDT, ULPS and trigger message transmissions. The BTA mode is designed to obtain various status information from slave in reverse direction. Functional simulation results show that the designed Escape and BTA modes work correctly for various conditions defined in MIPI DSI standard.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.43-49
• /
• 1998

The deep hole drilling has an increasing demands because of its wide range applications and its good productivity. The BTA drills are capable of machining for having a large length to diameter ratio in single pass to higher degree of accuracy and surface finish. It's really necessary that the investigation for the deep hole drilling by the BTA drill because its required quality should be satisfied with single pass. This thesis deal with the experimental results obtained during single tube BTA system machining on SM55C steel for different machining conditions. The results of the investigation on the optimum cutting condition selecting and tool life reveals as follows. (1) The optimum cutting condition was cutting speed, V = 42 m/min and feed speed. F = 90 mm/min and the tool life was about 10 meters. (2) Surface roughness was $12\mum$ and the roundness was less using $16mum$single edge BTA drill in testing cutting condition.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.131-143
• /
• 1994

The BTA(boring and trepanning association) deep hole machining has an increasing demands because of its wide applications and its good productivity. The main feature of the BTA tools is that the tool cutting edges are unsymmetrically located on the boring head. This provides a stabilizing cutting force resultant necessary for self guidance of the boring head. The BTA tools are capable of machining for having a large length to diameter ratio in single pass. A study of the accuracy and surface finish of holes produced would reveal quite useful information regarding the process. This study deals with the experimental results obtained during BTA machining on SM55C, SM45C steel under differnt machining conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.257-260
• /
• 1997

In order to investigate the volume resistivity on the electrical properties of transformer oils, the Transformer oils contained BTA is prepared, which was classified by the contents of BTA, such as 1[ppm], 10[ppm], 20[ppm], 30[ppm], 50[ppm], respectively. To measure the physical properties of transformer oils contained BTA, Fourier Transform Infrared Spectroscopy is investigated. And for the study of electrical properties is made by measuring the volume resistivity of each specimen. As result of this experiments, it is confirmed that the volume resistivity characteristics of specimen contained BTA 10[ppm] is superior.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.84-89
• /
• 1998

BTA drilling among the deep hole drilling is using for the improvement of productivity and the high-efficient working. As the deep hole drilling with BTA drill is satisfied with the required quality by one-pass processing, more deeper hole depth, the accuracy of materials is affected by bending vibration and cutting speed. This paper is studied that the shapes of material (surface roughness, roundness) is affected by cutting condition compared actual roundness with lobe shape with modeling of computer through the experiments in the BTA drilling system with BTA drill.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.267-269
• /
• 1997

The electrical properties due to the Benzotriazole(following as BTA) additive in fluids for insulating and cooling the ultra-high voltage transformer is studied in this paper. Specimen having the several contents of BTA, such as 5[ppm]. 10[ppm] and 30[ppm] is used in order to investigate the characteristics on volume resistivity in case of fluid flow in experimental device made in lab. Volume resistivity is decreased with an increase of fluid flow velocity and increased with BTA content in low temperature region, but volume resistivity of specimen contained BTA 10[ppm] is the largest thing over $30[^{\circ}C]{\sim}50[^{\circ}C]$ than the others in experiment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.75-79
• /
• 1996

가공품 중에서 구멍가공이 차지하는 비율은 매우 높으며 또한 가공정밀도가 요구되어진다. 그러나구멍의 직경에 비하여 길이가 길어지면 칩의 배출, 절삭날부의 윤활이 어려워지고, 공구의 진동문제가있기 때문에 일반적인 가공으로는 불가능할 경우가 많다. 따라서 이에 적절한 가공방법은 고압력의 절삭유를 공급할 수 있는 공구를 이용하여 가공할 수 있으며, 그 대표적인 방법으로는 Spade Drill, Gun Drill, 및 BTA Dill에 의한 깊은구멍가공봅이다. 본 연구에서는 Single Tube BTA 드릴링 시스템에서 Single Edge BTA Drill을 사용 하여 깊은 구멍을 가공할 때 공작물 SM55C의 최적절삭 조건의 선정과 공구수명에 대하여 실험을 통하여 분석 하고자 하였다.