• Journal of Advanced Marine Engineering and Technology
• /
• 제22권6호
• /
• pp.928-934
• /
• 1998

This paper describes a fully digitalized driver for BLDC motors which is realized by a single chip microprocessor. The speed change can be done by using the signal obtained from the position detecting sensor and adjusting the pulse width at the input channel of power module. In order to establish a speed control system a repetitive control method is adopted to track a periodic refer-ence change in the BLDC motor system. The experimental results show accurate reference track-ing performance under the given periodic reference in the repetitive controller design.

• 전기학회논문지
• /
• 제64권11호
• /
• pp.1639-1644
• /
• 2015

Auxiliary air compressor(ACM) applied to railroad cars is a device which controls amount of compressed air in order that pantographs can be mounted correctly on the roof of an electric train. Existing ACMs consist of dc motors and brushes wear out due to friction with a commutator. Therefore, continuous maintenance is required. However, three phase BLDC motors have higher power density compared to dc motors and the machine maintenance is not needed because electric commutation is possible. The three phase generally uses hall sensors to get position information and this enables the accurate control. This paper suggests an algorithm that compensates the errors occurred when the hall sensors have a breakdown for stable operation.

• 한국전자통신학회논문지
• /
• 제15권3호
• /
• pp.503-512
• /
• 2020

송풍기를 이용한 제품으로는 핸드드라이기, 자동세차기, 건조기, 청소기등이 있다. 이러한 전동기의 특징은 순간에 강한 바람이 나오도록 구조, 제어 알고리즘이 필요하다. 종래의 여자방식에 따른 전동기는 직권식, 분권식, 복권식, 영구자석식이 있다. 이러한 전동기는 고속 회전 시 기동전류가 크고 회전수가 불규칙한 단점이 있다. 이를 개선하고자 고속BLDC 전동기 제어에 관한 연구로 구동회로 설계, 센서리스 제어 알고리즘, 시뮬레이션, 실험 등을 통해 800W급 고속BLDC 모터 제어와 회로 설계하였고, 95% 이상 고효율을 제어기의 운전성능 평가 방법, 시제품 실험 및 검증을 연구하였다.

• Journal of Electrical Engineering and Technology
• /
• 제8권2호
• /
• pp.295-303
• /
• 2013

This paper reports an investigation of pulse width modulation (PWM) techniques for two-phase brushless DC (BLDC) motors fed by a two-phase eight-switch inverter in a fan application. The three-phase BLDC motor is widely applied in industry; however, a lower-cost two-phase BLDC motor and drive circuit has been greatly in demand in recent years. In this paper, we introduce a mathematical model of the two-phase BLDC motor with sinusoidal back electromotive forces (EMFs) based on traditional three-phase BLDC motors. To simplify the drive algorithm and speed up its application, we analyze the principle of block commutation for a two-phase BLDC motor drive in the 180-electrical-degree conduction mode, and we further propose five PWM schemes to improve the commutation performance of the two-phase BLDC drive. The effectiveness of the proposed PWM methods is verified through experiments.

• 한국소음진동공학회논문집
• /
• 제11권9호
• /
• pp.454-461
• /
• 2001

Acoustic noise and vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and electromagnetic origins through the motor air-gap. When a relative misalignment of rotor in the air-gap center exists on the assemblage, it is considered to influence the motor system characteristics. In this paper, the back electro motive force(BEMF) is analyzed by Finite Element Method(FEM) and verified by experiments for the SPM and IPM type motors. For magnetic field analysis, a FEM is used to account for the magnetic saturation. Using these results, the FEM is made to determine the appropriate electromagnetic field analysis in BLDC motors with rotor eccentricity ratio. A radial magnetic imbalance force of BLDC motor with rotor eccentricity is analyzed. Results demonstrate that the imbalance force is increased according to the degree of misalignment. An IPM motor, mostly chosen to realize high-speed operation, shows a worse effect on magnetic unbalanced forces and dynamic responses compared with SPM motor due to magnetic saturation when the rotor eccentricity exists.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제9권2호
• /
• pp.99-104
• /
• 2009

The turn-to-turn short is one major fault of the motor faults of BLDC motors and can appear frequently. When the fault happens, the motor can be operated without breakdown, but it is necessary to maintain the motor for continuous working. In past research, several methods have been applied to detect winding faults. The representative approaches have been focusing on current signals, which can give important information to extract features and to detect faults. In this study, current sensors were installed to measure signals for fault detection of BLDC motors. In this study, the Park's vector method was used to extract the features and to isolate the faults from the current measured by sensors. Because this method can consider the three-phase current values, it is useful to detect features from one-phase and three-phase faults. After extracting two-dimensional features, the final feature was generated by using the two-dimensional values using the distance equation. The values were used in fuzzy similarity to isolate the faults. Fuzzy similarity is an available tool to diagnose the fault without model generation and the fault was converted to the percentage value that can be considered as possibility of the fault.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제9권1호
• /
• pp.1-12
• /
• 2009

BLDC motors are stored in the devices such as CD-RW, COMBO, DVD-ROM and CD-ROM. It is indispensable to establish reliability assessment criteria for BLDC motors, especially in the world where IT grows rapidly. In this article, reliability certification procedure is given. The reliability certification procedure consists of two separate tests such as quality certification test and lifetime test. The former quality certification test comprises general performance test and environmental test. Items which pass the test undergo lifetime test which guarantees the extent of mean lifetime with certain confidence.

• 산업기술연구
• /
• 제29권B호
• /
• pp.165-171
• /
• 2009

This paper proposes a sensorless control method of BLDC motors using line-to-line back-EMFs. Typical sensorless control methods have various problems such as the difficulty in operation at low speed and difficulties in application and so forth. However, the control method using line-to-line back-EMFs that this paper proposes solved not only such problems but also problems of noise and difficulty of commutation detection. The method is to divide line-to-line back EMF into the constant. With 550[W] BLDC motor driving system, simulations and experiments have been carried out for the verification of the proposed control method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 학술대회 논문집 전문대학교육위원
• /
• pp.95-99
• /
• 2001

In this paper, a drive system for multi-phase bipolar brushless DC (MPB BLDC) motor is presented. This drive system is used for an electric bicycle. In general, the maximum and minimum speed of electric bicycle are required by law. At first, the proposed controller is satisfied for the limited speed control. Secondly, the system has a technique of exited with modulation(EWM), bidirection control, and partial square wave control. Thirdly, the controller is designed for system stability Experimental results show the performance of the proposed controller of MPB BLDC motors for an electric bicycle.

• 전기학회논문지P
• /
• 제51권4호
• /
• pp.219-221
• /
• 2002

This paper presents an electric scooter development using blushless DC motor. In recent scooters was to develop for sport leisure and short transportation. Most of scooter are used petroleum gas. This gas scooter has disadvantage to pollute the air. Some of scooters have developed by DC motor which require a brush. However brushless motors have higher maximum speed and greater capacity, save maintenance labour and produce less noise. There is also greater freedom in planing the usage of brushless motors. In this paper we develop an electric scooter driving BLDC motor for design smart system and control speed of scooter with current reference signal to apply voltage to motor by means of three phase inverter. Using accelerator device we generate current reference to control speed and send the current to a MICOM by A/D converter. This MICOM produces the voltage signal and hall sensors signal and PWM controller drive three phase inverter to minimize error between the reference and an actual current.