• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.3
• /
• pp.15-29
• /
• 2001

For the pertinent use of NMT method, both characteristics of joints (JRC, JCS and ${\phi}_r$) and characteristics of rock mass (Q-Value) must be investigated carefully. The main objective of the study presented is to investigate how sensitive the predicted behaviour of an underground excavation is to various realistic assumptions about some input parameter for the jointed rock mass. Joint pattern in the tunnel is predicted by statistical approach (chi-square test). In this paper, sensitivity studies involving in joint characteristics were carried out. The parametric studies involving change in Barton-Bandis joint model have shown that JCS is relatively insensitive to JRC and ${\phi}_r$. An increase in JRC value may not, according to the Barton-Bandis model, necessarily lead to a decrease in displacement. The importance of dilation in predicting the behaviour of a rock mass around an excavation is emphasized from a comparison of the Barton-Bandis joint behaviour model with the Mohr-Coulomb model. The Barton-Bandis model predicted higher stress, which allow for the build-up of stress caused by dilatant behaviour.

• Proceedings of the KSEEG Conference
• /
• 2001.04a
• /
• pp.203-205
• /
• 2001

• Tunnel and Underground Space
• /
• v.9 no.2
• /
• pp.141-148
• /
• 1999

Distinct element simulation in jointed rock masses is largely dependent upon the joint constitutive equation used. This paper describes the differences between the Barton-Bandits (BB) and the Mohr-Coulomb (MC) joint constitutive models for the stability analysis of the jointed rock slopes. The BB model, which allows the modelling of the dilation accompanying shear, predicts results very similar to the present condition of slopes. Consequently the 10 cm thick shotcrete was proposed for the reinforcement of those slopes. The MC model, however, in which the dilation angle is constant, is relatively insensitive to the behaviors of joints.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.8
• /
• pp.41-51
• /
• 1997

The device simulator (BANDIS) which can analyze efficiently the electrical characteristics of the semiconductor devices under the three dimensional stationary conditions on the IBM PC was developed. Poisson, electon and hole continuity equations are discretized y te galerkin method using a tetrahedron as af finite element. The frontal solver which has exquisite data structures and advanced input/output functions is dused for the matrix solver which needs the highest cost in the three dimensional device simulation. The discretization method of the continuity equations used in BANDIS are compared with that of the scharfetter-gummel method used in the commercial three-dimensional device. To verify an accuracy and the efficiency of the discretization method, the simulation results of the PN junction diode and the BJT from BANDIS are compared with those of the commercial three-dimensiional device simulator such as DAVINCI. The maximum relative error within 2% and the average number of iterations needed for the convergence is decreased by more than 20%. The total simulation time of the BJT with 25542 nodes is decreased to about 60% compared with that of DAVINCI.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.51-58
• /
• 2001

The Distinct Element Method (DEM) was used to analyze the stability of jointed rock slope, of which dimension are about 200m(length), 60m(height), $55^{\circ}$ dip. The Barton-Bandis joint model was used, as a constitutive model. The parameters such as JRC and spatial distribution characteristics of discontinuities were acquired through field investigation. Three different cases such as $51^{\circ}$, $45^{\circ}$ and $38^{\circ}$ in angle of rock slope were analyzed to decide a stable slope. To keep the jointed rock slope safely, it is proposed to reduce the height of slope from 60m to 48m and to reduce the angle of the from $55^{\circ}$ to $38^{\circ}$ too.

• Tunnel and Underground Space
• /
• v.11 no.2
• /
• pp.167-173
• /
• 2001

The joint model has influence on the results of discontinuum analysis. In this study the results of discontinuum analysis with Barton-Bandis joint model(BB model) and with Mohr-Coulomb joint model(MC model) are compared. The results of continuum analysis under the same condition are compared with the results of discontinuum analysis to investigate the behavior of rockmass around tunnel. The result of continuum analysis and that of discontinuum analysis with BB model show similar distribution of displacement and stress. On the other hand, the discontinuum analysis with MC model shows different displacement distribution and stress distribution. Moreover, the displacement and minor principal stress of the discontinuum analysis with MC model are smaller than those of continuum analysis, although the joints are explicitly considered in the discontinuum analysis. These results are originated from the limitation of MC model in simulating joint deformation behavior, especially the assumption of constant dilation jingle independent of it)int 7hear displacement.

• Geomechanics and Engineering
• /
• v.8 no.3
• /
• pp.391-414
• /
• 2015

In this paper, stabilities of a plane slide rock slope under different hydraulic distributions were studied based on the nonlinear Barton-Bandis (B-B) failure criterion. The influence of various parameters on the stability of rock slopes was analyzed. Parametric analysis indicated that studying the factor of safety (FS) of planar slide rock slopes using the B-B failure criterion is both simple and effective and that the effects of the basic friction angle of the joint (${\varphi}_b$), the joint roughness coefficient (JRC), and the joint compressive strength (JCS) on the FS of a planar slide rock slope are significant. Qualitatively, the influence of the JCS on the FS of a slope is small, whereas the influences of the ${\varphi}_b$ and the JRC are significant. The FS of the rock slope decreases as the water in a tension crack becomes deeper. This trend is more significant when the flow outlet is blocked, a situation that is particularly prevalent in regions with permafrost or seasonal frozen soil. Finally, the work is extended to study the reliability of the slope against plane failure according to the uncertainty from physical and mechanics parameters.

• Geomechanics and Engineering
• /
• v.20 no.4
• /
• pp.287-297
• /
• 2020

This paper investigates the stability of a three-dimensional (3D) wedge under the pseudo-static action of an earthquake based on the nonlinear Barton-Bandis (B-B) failure criterion. The influences of the mechanical parameters of the discontinuity surface, the geometric parameters of the wedge and the pseudo-static parameters of the earthquake on the stability of the wedge are analyzed, as well as the sensitivity of these parameters. Moreover, a stereographic projection is used to evaluate the influence of pseudo-static direction on instability mode. The parametric analyses show that the stability coefficient and the instability mode of the wedge depend on the mechanical parameter of the rock mass, the geometric form of the wedge and the pseudo-static state of the earthquake. The friction angle of the rock φ_b, the roughness coefficient of the structure surface JRC and the two angles related to strikes of the joints θ₁ and θ₂ are sensitive to stability. Furthermore, the sensitivity of wedge height h, the compressive strength of the rock at the fracture surface JCS and the slope angle α to the stability are insignificant.

• Journal of IKEEE
• /
• v.6 no.2 s.11
• /
• pp.119-127
• /
• 2002

An algorithm for analyzing the characteristics of the power BJT using numerical analysis method is proposed. The Fermi-Dirac statistics is used to calculate the carrier concentration in highly doped region. Philips Unified mobility model, SRH model and Auger model is used to calculate the recombination current of base region. To verify the accuracy of the proposed method, the collector current of BANDIS is compared with the measured data in the condition of the base current increased from $1.0[{\mu}A]\;to\;3.5[{\mu}A]$. The collector current of BANDIS show a maximum relative error within 8.9% compared with the measured data.

• Tunnel and Underground Space
• /
• v.11 no.2
• /
• pp.109-119
• /
• 2001

Up to now single large cavern was excavated for each undergroud hydraulic powerhouse in Korea. But the Yangyang underground hydraulic powerhouse consists of two large caverns; a powerhouse cavern and main transformer cavern. In this carte, the structural stability of the caverns, especially the rock pillar formed between two large caverns, should be guaranteed to be sound to make the caverns permanently sustainable. In this research, the Distinct Element Method(DEM) was used to analyze the structural stability of two caverns and the rock pillar. The Barton-Bandis joint model was used as a constitutive model. The moot significant parameters such as in-site stress, JRC of in-situ natural joints, and spatial distribution characteristics of discontinuities were acquired through field investigation. In addition, two different cases; 1) with no support system and 2) with a support system, were analysed to optimize a support system and to investigate reinforcing effects of a support system. The results of analysis horizontal displacement and joint shear displacement proved to be reduced with the support system. The relaxed zone in the rock pilar also proved to be reduced in conjunction with the support system. Having a support system in place provided the fact that the non zero minimum principal stresses were still acting in the rock pillar so that the pillar was not under uniaxial compressive condition but under triaxial compressive condition. The structural stability f an approximately 36 m wide rock pillar between two large caverns was assured with the appropriate support system.