The using of composite material is an aviation field but it changes into a general industry. Especially composites are expanding the use on transportation vehicles like automobiles, ships, and aircrafts. The main factor of this expansion is high specific strength. It can supply a high quality and efficiency of energy. But manufacturing of composite products requires many raw materials and tooling cost for special process, so we needs a reduction of these costs to achieve best efficiency. In the present study, we contrast the change of mechanical and physical properties between VaRTM(Vacuum Assisted Resin Transfer Molding) and hand lay-up process. VaRTM process can offer a high quality the same as autoclave products, and low cost like hand lay-up process. In the results of mechanical tests, VaRTM specimen is stronger than hand lay-up specimen and hand lay-up specimen became delamination. In the results of physical tests, the resin content of VaRTM specimen is lower than hand lay-up specimen. On micrograph, the strength of specimen by VaRTM between fiber and resin is stronger than that of one by hand lay-up. And the specimen by hand lay-up contains more defects than one by VaRTM. So, VaRTM process can practically apply for automobile engine hood. This paper shows that VaRTM process is one of the most suitable processes for composite parts of automobile.
본 연구에서는 von Hippel(2005)의 사용자 혁신 이론을 바탕으로 LBS 분야의 대표적 응용 서비스인 자동차 네비게이션 산업에서 특히 지도 중심의 콘텐츠 확보와 개발을 위한 사용자 혁신 활용 사례를 발굴하고자 한다. 사용자 혁신에 관한 von Hippel의 7가지 특성을 기준으로 M&Soft의 자동차 네비게이션 제품 개발 및 유지 보수 과정을 분석해본다. 이를 통해, 사용자 혁신의 성공적인 활용을 위한 판매자의 3가지 전략적 대응 중, M&Soft는 사용하기 쉬운 정보 기술 플랫폼을 제공하여 회원들이 쉽게 각종 지도 및 이동상의 정보나 아이디어들을 제공하도록 유도하는 정도에 국한되어 있음을 확인하기도 하였다. 본 연구의 의의는 실물 제품을 바탕으로 전개된 von Hippel의 이론을 인터넷 기반의 콘텐츠 서비스가 점점 중요해지는 추세에 맞춰 디지털 서비스 및 제품에 적용시켜 보았다는 점이다.
Background: This study was conducted to provide preventive measure for the musculoskeletal disorders in automobile parts manufacturing workers. Method: The author surveyed to the musculoskeletal symptoms prevalence and its related factors from 10th to 17th April 2011 with structured self administered questionnaires. 223 out of 225 collected questionnaires were used for final analysis, excluding 2 questionnaires with no valid response. Based on the diagnostic criteria of NIOSH (National Institute for Occupational and Health), an investigation was made into the prevalence of musculoskeletal symptoms as well as into the factors related to individual items. Results: The prevalence of musculoskeletal symptoms according to the criteria of NIOSH was the highest in the shoulder (52.9%), followed by the neck (39.%), the hand/wrist (35%), the waist (29.6%), the arm/elbow (24.7%), and the leg/food (23.8%). One-way analysis showed that among general characteristics, age was the musculoskeletal risk factor with the greatest effect. Whereas among work-related characteristics, significant risk factor didn't find. Yet it was shown that among ergonomic work postures, high degree of musculoskeletal risk was shown by the posture involving frequent and repetitive movement of the arm and the hand/wrist and also by the posture involving standing for a long time. Multiple regression analysis showed that musculoskeletal risk was 1.795 times higher in those age 50 and over than in those under age 50; 1.67 times higher in the high risk stress group than in the low risk stress group; and 1.131 higher in the group involving the repetitive use of the hand/arm than in the other groups (p<.05). Conclusion: The prevalence and stress score of automobile parts manufacturing workers were higher than other occupation workers. Among general characteristics, drinking and smoking were shown to be related to stress score; while age was shown to have significant effect on musculoskeletal risk.
The using of composite material is an aviation field but it changes into a general industry. Especially composites are expanding the use on transportation vehicles like automobiles, ships, and aircraft. The main factor of this expansion is high specific strength. It can supply a high quality and efficiency of energy. But manufacturing of composite products requires many raw materials and tooling cost for special process, so we needs a reduction of these costs to achieve best efficiency. In the present study, we contrast the change of mechanical and physical properties between VaRTM(Vacuum Assisted Resin Transfer Molding) and hand lay-up process. VaRTM process can offer a high quality the same as autoclave products, and low cost like hand lay-up process. In the results of mechanical tests, VaRTM specimen is stronger than hand lay-up specimen and hand lay-up specimen became delamination. In the results of physical tests, the resin content of VaRTM specimen is lower than hand lay-up specimen. On micrograph, the strength of specimen by VaRTM between fiber and resin is stronger than that of one by hand lay-up. And the specimen by hand lay-up contains more defects than one by VaRTM. So, VaRTM process can practically apply for automobile engine hood. This paper shows that VaRTM process is one of the most suitable processes for composite parts of automobile.
Korea's automobile industry, which has grown rapidly to become the world's fifth-largest automobile producer, To cope with environmental pollution and energy problems in order to prevail competitive edge in global market We are investing a lot of research personnel and costs. Among them, for realizing alternative light weight It is a part of the automobile module system that has achieved the technological development before the breakthrough in the injection molding process in the press process. Door module PNL was the subject of research. The door module PNL is expected to cause warpage before the mold production due to the thin and flat product characteristics and fiber orientation characteristic of the material. In this paper, CAE analysis and reverse correction tool Design. CAE analysis to obtain the results of weld line position, bending position and deformation value Through the correction tool, think3, the original product was modified before the mold production to improve the completeness of the parts. In fiber orientation, the position and size of the cooling channel in the mold, the position and size of the gate, Temperature, pressure, time, and work environment. Compared with the result of CAE analysis, the product that was reverse-corrected by Think3 was manufactured, and injection molding was performed. Injection molding products were tested 24 hours later. 3.5 mm to 7.0 mm, and under the fixed condition, the deviation was from 1.1 mm to 1.5 mm. Unlike the CAE analysis, the deviation of the actual injection pressure and the cooling temperature, the fiber orientation of the material, In order to solve this problem, it is necessary to compare the injection conditions with the database, I knew I had to catch the standard.
The proportion of software in the automotive industry is steadily increasing due to the rapid technological development of automobile E/E parts. Because the automotive E/E technology is now on the basis of intelligent automobile and advanced safety automobile technology. The purpose of this study is to investigate the effect of organizational capability (organizational resource capability and management capability), process capability (process capability, customer Requirement management capability), performance dimension (motivation, participation level). In this study, we conducted questionnaires and statistical analysis on engineers (members of the Korea Advanced Automotive Technology Association) who perform research and development activities in the R&D organization of the automotive E/E part in South Korea. ANOVA is applied for the verification of the difference in performance measured by organizational capability, process maturity, and motivation participation level according to company characteristics (level of processing : supply chain configuration, annual sales, total SW development ratio). According to the results of this study, in order to improve the performance of ASPICE or ISO 26262-related consulting project, a different consulting approach strategy considering the characteristics of organization and personnel is needed. In summary, the analysis results for the three main treatment levels are as follows. The difference in organizational capacity, process capability and performance was found to be statistically significant according to supply chain configuration and annual sales, but it was found that the difference of response according to the proportion of total SW was not significant.
It has been very important to have an exact evaluation for risk factors in order to prevent WMSDs(Work-related Musculoskeletal Disorders). However, most WMSDs evaluation methods have always been some problems of possibilities associated with subjective evaluation. Therefore, this study tried to conduct a sort of usability analysis on three major evaluation methods(OWAS, RULA, REBA). Specifically, major subjects in the study consisted of three parts as follows; comparison of the results between experienced and inexperienced observers, analysis for the consistency of the results in terms of different evaluation times, and analysis for the consistency of the results in terms of different job characteristics(based on the part of the automobile). The results of the study were summarized as follows; 1) There was statistically significant difference of the results by RULA and by REBA between experienced and inexperienced observers. This might be due to the fact that experienced observers have had better ability to detect the important working posture during evaluation. However, the results by OWAS did not give any significantly different results between experienced and inexperienced observers, 2) All three checklists applied by experienced subjects did not show any single result significantly different in terms of different evaluation times. This might have to do with high intra-observer reliability from some of previous studies, 3) The five parts of an automobile were selected as five major jobs with different job characteristics in the automobile industry. Specifically, they were door part, front part(hood, etc.), inside part(dash board, seats, etc.), rear part(trunk etc.), and bottom part. All three methods did not show any significant differences for the results from each observers. Further study on this subject would eventually provide a sophisticated evaluating guidelines for WMSDs regarding determination of observer-specific evaluation, identification of repetitive number of evaluations for stable results for each checklist, determination of job-specific evaluation methods, and so on.
본 논문은 자동차용 임베디드 시스템에 탑재되는 운영체제의 실시간 스케줄링 알고리즘에 대해서 개선된 알고리즘을 제안한다. 기존 OSEK OS의 스케줄링 알고리즘에서 큰 차이를 보이는 부분은 16개의 우선순위 대기 큐를 4개의 우선순위 대기 큐로 줄였다. 그리고 대기 큐에서 FIFO 알고리즘을 사용하지만 제안하는 스케줄링 알고리즘은 EDF 알고리즘을 사용하여 실시간성을 좀 더 높였다. 제안한 스케줄링 알고리즘에 대해서 간단한 실험을 수행하였다. 실험 결과 FIFO 알고리즘을 사용한 기존 OSEK OS의 경우 평균 26.29ms이고, 제안한EDF 알고리즘을 사용한 경우 평균 26.13ms로 제안한 EDF 알고리즘을 사용한 경우가 0.16ms 정도 빠름을 알 수 있다. FIFO 알고리즘을 사용한 기존 OSEK OS의 스케줄링 알고리즘 보다 제안하는 EDF 스케줄링 알고리즘을 사용한 스케줄링 알고리즘이 우수함을 알 수 있다.
현재의 실내 실외의 조명 산업은 반도체 LED를 이용한 R(빨강), G(초록), B(파랑)를 각각 제어 연출하여 대형화, 시스템화 되어가고 있다. 조명 산업의 통신 제어 표준인 DMX512(ANSI E1.11) 프로토콜은 최대 512개의 조명등 또는 24bit 트루 칼라로 표현할 경우 최대 170개의 조명등을 연출할 수 있다. 요즘 100개 이하의 조명등 연출은 소규모 연출로 분류되고 있어 본 논문은 1000개 이상의 대용량 조명 연출을 위하여 1대 마스터 컨트롤러에 최대 32대의 슬레이브 컨트롤러를 연결할 수 있는 마스터-슬레이브 구조를 제안한다. 또한, 슬레이브 컨트롤러들이 설계된 하나의 연출을 달성하기 위한 동기화(synchronization) 방안도 제안한다. 제안하는 방안은 마스터가 400ms 마다 동기화 신호를 송신하고 슬레이브들은 이 신호를 수신하여 DMX512 출력의 기본이 되는 타이머를 초기화하여 동기화를 구현하였다. 제안된 방안으로 설계 제작되어 상용화된 운영 사례를 소개한다.
There are many assessment techniques used for occupational risk factors of MSDs in the workplaces. However, because all ergonomic assesment techniques or tools are based on theoretical background derived from workphysiology, biomechanics, psychophysics, industrial hygiene, work system, and etc, it is impossible to compare the assessment techniques. This study was conducted to compare the excess rates of risk factors among ergonomic assessment techniques and to make alternative methods. Site-visits to 6 automobile products and parts company provided data for process repeated work where the produced data was examined for evaluating the relationship between workplace lay-out and work posture by using ergonomic assessment techniques. We evaluated 157 jobs for simple repeated work and 37 jobs for manual materials handling (MMH). In simple repeated work, the exceeded rates of AC were 36.3% in OWAS method and 93.0% in RULA method. The exceeded rate for RULA method was significantly higher than those for OWAS method (p<0.05). In MMH, the exceeded rates of AC were 80.0% in NLE method and 76.5% in WAC method. Statistically significant differences were not identified in the exceeded rates for NLE and MAC methods (p<0.05). The analyzed results among ergonomic assessment techniques (OWAS, RULA, NLE/WAC) were applied to the same work places performing simple repeated work and manual materials handling simultaneously. The applied results showed statistically significant differences (p<0.05) among ergonomic assessment techniques (OWAS, RULA, NLE/WAC). Exceeded rates of four ergonomic assessment techniques in decreasing order was "RULA>NLE>WAC>OWAS". The RULA method was the strongest assessment technique for automobile products and parts company. We discovered that the results could easily be overestimated or underestimated when the ergonomic assessment techniques were not applied correctly during the evaluation process. Therefore, we recommend using at least 2 methods when evaluating and analysing the results.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.