• 방재기술
• /
• 통권12호
• /
• pp.5-9
• /
• 1992

This reoprt is explained about test results of pressure operated switch for automatic fire extinguishing systems. It may include pressure operated Switch for automatic water supply control valves for use in automatic fire suppression system for fire protection service. The testing program was progressed devided by Two testing items, extermal oppearane test and performance test. The object of this report is present the problem which appear from the analysis of test results.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.373-378
• /
• 2003

In this paper, build up of fan performance tester in KITECH was introduced. The fan tester was set up based on AMCA standards 210-99, ANSI/ASHRAE 51-1999 with maximum flowrate within $1000\;m^{3}/min$. Both of inlet and outlet chamber setup with multiple nozzles described in AMCA 210 were established. The development of fully automatic control and measurement system are described. With this system, the accuracy of fan performance test can be maintained through the various flowrate and the uncertainty can be reduced.

• 한국컴퓨터정보학회논문지
• /
• 제23권7호
• /
• pp.1-10
• /
• 2018

In this paper, we propose the principles and design details of Automatic cable assembly test system and show its utility. Testing the cable assembly is required periodically or non-periodically in the system that the cable assembly performance is quite important like military equipment. There are several weaknesses when humans test the cable assembly manually. It not only takes much time but also could happen human error. To improve these disadvantages, I developed Automatic cable assembly test system. The system can be implemented by building switching control system that connect and disconnect the cable assembly and measuring devices. Through the result of the cable assembly test with this test system, we show this system makes test time short and improves of test reliability as compared with manual test.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1231-1236
• /
• 2007

Balance Shaft Module is module parts that is installed to vehicles engine to reduce noise and vibration of vehicles engine. Balance Shaft Module's performance exerts important influence on performance of engine. Therefore, must be able to warrant quality and performance of Balance Shaft Module. Existing product found and revised error at continuous process of production, and estimated failure mode in Balance Shaft Module. Previous method hard to secure product that performance is excellent, and bring a lot of damages economically. Therefore, development of inspectin system for quality inspection of parts and performance test of assembly is essential in Balance Shaft Module. In this study, represented development process of automatic dynamic inspection system to test performance and detect breakdown of Balance Shaft Module that is producing in Dongbo.

• 유공압시스템학회논문집
• /
• 제3권4호
• /
• pp.21-28
• /
• 2006

The proportional control solenoid valves as well as the PWM solenoid valves operated by electric signal play an important role in the hydraulic system for automatic transmissions to improve the shift quality. However it is not generally available for the performance data because most of the automotive parts manufacturer don't release the specific test results, especially dynamic performance that is essential to design a shift control algorithm. In this research, a performance test equipment that can be applied to various types of pressure control solenoid valve was developed. It was implemented by 8-bit micro-controller with many useful functions such as adjustable PWM carrier frequency, embedded function generator, current controller, data monitoring and acquisitions, etc. for the test of dynamic performance of solenoid valve as well as the steady-state pressure characteristics. The performance test results for the direct type proportional control solenoid valve show not only the validity of overall functions but also its usefulness as a hydraulic valve tester.

• 한국항해항만학회지
• /
• 제33권9호
• /
• pp.603-608
• /
• 2009

In this paper, a 3m-class free running model ship will be introduced with its manoeuvring performance experiments. The results of turning circle test and zig-zag test will be explained. The developed system are equipped with GPS, main control computer, wireless LAN, IMU (Inertial Measurement Unit), self-propulsion propeller and driving rudder. Its motion can be controlled by RC (Radio Control) and wireless LAN from land based center. Automatic navigation is also available by pre-programmed algorithm. The trajectory of navigation can be acquired by GPS and it provides us with important data for ship's motion control experiments. The results of manoeuvring performance experiment have shown that the developed free running model ship can be used to verify the test of turning circle and zig-zag. For next step, other experimental researches such as ship collision avoidance system and automatic berthing can be considered in the future.

• 한국컴퓨터정보학회논문지
• /
• 제26권6호
• /
• pp.63-71
• /
• 2021

본 논문에서 운용자의 지속적인 작업 없이 휴대용탐지장치의 기능 및 성능시험을 원격으로 수행하기 위한 무인자동화시험시스템의 설계 개선을 위해 TRIZ 방법론의 기술적 진화법칙(TESE, Trends of Engineering System Evolution)을 적용한 방안을 제안한다. 시험에 소요되는 시간과 비용을 고려하여 휴대용탐지장치 한 대당 소요되는 시간 비용을 최소화하고 한번 시험시 최대한 많은 수의 휴대용탐지장치를 시험할 수 있도록 개선된 효율적인 설계 개발 방안을 도출한다. 또한 설계된 구조와 개선된 설계 구조에 대한 3D 모델링 형상을 설계하여 설계 개선 전과 후의 무인자동화시험시스템을 비교한다. 여기서 제안된 방안을 적용한 무인자동화시험시스템은 기존 시험시스템의 여러 가지 단점들을 해결함으로써 이상성을 높이고 휴대용탐지장치의 기능 및 성능시험 효율을 향상시킬 수 있을 것으로 기대된다.

• 제어로봇시스템학회논문지
• /
• 제10권2호
• /
• pp.131-138
• /
• 2004

Automatic flight control system (AFCS) for a low-cost unmanned aerial vehicle is described in this paper. Development process and block diagram of the AFCS are introduced. The flight control law for longitudinal and lateral channel autopilot is designed using optimization process. In this procedure, the performance index is composed of desired location of closed loop system poles and H$_2$norm of the resultant flight control system. This procedure is applied to the autopilot design of an unmanned target vehicle. Performance of the AFCS is evaluated by processor-in-the-loop simulation test and flight test. These results show that the AFCS has acceptable performance fur low cost UAV.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.367-371
• /
• 2004

This paper describes development of automatic flight control system for an unmanned target drone which is operated by Korean army as for anti-air gun shooting training. Current target drone is operated by pilot control of on-board servo motor via remote control system. Automatic flight control system for the target drone greatly reduces work load of ground pilot and can increase application area of the drone. Most UAVs being operated now days use high-priced sensors as AHRS and IMU to measure the attitude, but those are costly. This paper introduces the development of low-cost automatic flight control system with low-cost sensors. The integrated automatic flight control system has been developed by integrating combining power module, switching module, monitoring module and RC receiver as an one module. The performance of automatic flight control system is verified by flight test.

• Journal of Biosystems Engineering
• /
• 제42권3호
• /
• pp.147-154
• /
• 2017

Purpose: To reduce the costs of potato seeds and labor of workers, a fully automatic in-situ seeding machine for cutting seed potatoes was developed. Methods: An experiment was conducted to evaluate the seeder performance of the prototype of potato planter by cutting seeds in farmlands from March to April 2017. The study tested the seeder performance at working speeds ranging from 0.28 to 0.45 m/s. The seeding rate and seeding distance were also investigated according to the planned distance between planted seeds from 20 to 30 cm, with 5 cm intervals. Results: Tests on the performance of the developed cutting blade on the automatic potato seeder show that whole potatoes should be used instead of half potatoes. The seeding rates were 88.8% and 82.5% for whole and half potatoes, respectively. When the tractor working speed was increased from 0.28 to 0.45 m/s, the successful seeding rate decreased from 98.8% to 96.3%, respectively. However, with planted seed distances of 20, 25, and 30 cm, the successful seeding rates were near 98%. Conclusions: The developed automatic potato seeder can to improve the labor productivity and cultivation environment of potato farms by the mechanization of the seeding process, which is currently associated with high-labor, -costs, and -hours. Therefore, based on this study, the developed automatic potato seeder provides the mechanization necessary for improved potato cultivation conditions in farmlands.