• International Journal of Highway Engineering
• /
• v.15 no.2
• /
• pp.19-27
• /
• 2013

PURPOSES : This study aims to investigate the snow-melt effects of an underground electric heater's snow-melt system via a field performance test, for evaluating the suitability of the system for use on a concrete pavement. The study also investigates the effectiveness of dynamic measures for clearing snow after snowfall events. METHODS : In order to check the field applicability, in November 2010, specimens were prepared from materials used for constructing concrete pavements, and underground electric heating meshes (HOT-mesh) were buried at depths of 50 mm and 100 mm at the site of the Incheon International Airport Construction Research Institute. Further, an automatic heating control system, including a motion sensor and pavement-temperature-controlled sensor, were installed at the site; the former sensor was intended for determining snow-melt effects of the heating control system for different snowfall intensities. Pavement snow-melt effects on snowy days from December 2010 to January 2011 were examined by managing the electric heating meshes and the heating control system. In addition, data on pavement temperature changes resulting from the use of the heating meshes and heating control system and on the dependence of the correlation between the outdoor air temperature and the time taken for the required temperature rise on the depth of the heating meshes were collected and analyzed. RESULTS : The effects of the heating control system's preheat temperature and the hot meshes buried at depths of 50 mm and 100 mm on the melting of snow for snowfalls of different intensities have been verified. From the study of the time taken for the specimen's surface temperature to increase from the preheat temperature ($0^{\circ}C$) to the reference temperature ($5{\sim}8^{\circ}C$) for different snowfall intensities, the correlation between the burial depth and outdoor air temperature has been determined to be as follows: Time=15.10+1.141Depth-6.465Temp CONCLUSIONS : The following measures are suggested. For the effective use of the electric heating mesh, it should be located under a slab it may be put to practical use by positioning it under a slab. From the management aspect, the heating control system should be adjusted according to weather conditions, that is, the snowfall intensity.

• Convergence Security Journal
• /
• v.7 no.3
• /
• pp.87-93
• /
• 2007

We propose a mobile point-of-sale system, which consists of only mobile information terminals and personal computers. The proposed system provides most of functionalities related with resource planning, adminstration and management, provided by medium-scale or large-scale POS systems, with additional functionalities, such as automatic information gathering and management through mobile interconnection, while eliminating the necessity of additional special-purpose devices, such as bar-code systems. The proposed system transmits order information through wireless and wired communication lines, thus allowing real-time sharing of order information among diverse information devices, such as mobile order receiving terminals, main server within stores, monitors and printers located in production lines. Also, the system is able to transfer such detail information produced within stores in real-time to the enterprise-level accounting, sales, logistics, personnel management system, which facilitate enterprise-wide management and administrative decision-making. No additional programs are required for mobile terminals. Order information received by such terminals are entered into databases through web server of main server and that information is again transferred to main server and production line printers. The proposed system can handle all the point-of-sale information and can provide almost of the POS functionalities by simply utilizing wireless internet, personal computers, and mobile terminals without installing specific-purpose peripheral devices. The proposed system can be widely applied to the small-scale stores and will contribute in reducing construction and maintenance cost required for point-of-sale management.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.6
• /
• pp.1147-1159
• /
• 2018

This study focuses on the verification of a rapid protection automation system using an inflatable structure. The inflatable structure is an automatic rapid protection system against human and material damage when the subsea tunnel is flooded. Especially, it is essential for construction and operation of subsea tunnels. In this study, we have experimentally verified the rapid protection automation system using the inflatable structure designed for this problem. In order to verify this, a model tunnel with a 40: 1 reduction ratio was constructed, and air pressure of 0.1 bar and 0.15 bar was injected to divide the tunnel according to the expansion rate at 10 sec and 20 sec. According to the results of the study, the protection efficiency was better at 0.15 bar than 0.1 bar when the expansion structure was expanded, and the protection efficiency and influent control efficiency were different according to the pneumatic injection time of the inflating structure. As a result of this study, it was found that the higher the internal air pressure of the inflated structure and the faster the inflation of rate, the more effectively the inflated structure was inflated. As a result of this study, it is necessary to further study the wedge type structure which is useful for the storage method of expansion structure, shape and expansion derivative, inhibition of expansion structure during protection and control of inflow water.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.1
• /
• pp.95-107
• /
• 2017

In this study, a preliminary study was undertaken for development of a tunnel incident automatic detection system based on a machine learning algorithm which is to detect a number of incidents taking place in tunnel in real time and also to be able to identify the type of incident. Two road sites where CCTVs are operating have been selected and a part of CCTV images are treated to produce sets of training data. The data sets are composed of position and time information of moving objects on CCTV screen which are extracted by initially detecting and tracking of incoming objects into CCTV screen by using a conventional image processing technique available in this study. And the data sets are matched with 6 categories of events such as lane change, stoping, etc which are also involved in the training data sets. The training data are learnt by a resilience neural network where two hidden layers are applied and 9 architectural models are set up for parametric studies, from which the architectural model, 300(first hidden layer)-150(second hidden layer) is found to be optimum in highest accuracy with respect to training data as well as testing data not used for training. From this study, it was shown that the highly variable and complex traffic and incident features could be well identified without any definition of feature regulation by using a concept of machine learning. In addition, detection capability and accuracy of the machine learning based system will be automatically enhanced as much as big data of CCTV images in tunnel becomes rich.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3911-3916
• /
• 2010

In this paper we describe contents and results on running test for ATP on-board equipment, which has propelled as one of the research projects, so called, "Reliability assessment and operation technology development for Korean-type tilting trains" in order to ensure the safety and operation efficiency of tilting trains. We developed tilting trains for the speed-up of conventional lines and for the passenger service improvement where the KTX is not available. And we made progress the operation trial test in the 120,000 km distance with the use of ATS equipment, used in existing lines, for the purpose of the reliability assessment of the developed tilting trains. We decided to accelerate the speed for more than 200km/h with respect to the 6 existing lines including Jungang-line and Chungbuk-line where KTX has not operated. According to this decision, Train control system is to be changed from ATS to ATP. We should have installed an ATP on-board unit in tilting trains and verified the operational suitability, therefore we installed the same ATP on-board unit on tilting trains as that used in the ATP construction project on Gyeongbu-line and Honam-line, and verified that the function and performance of the installed ATP on-board unit conformed to the tilting trains operation.

• Journal of Animal Environmental Science
• /
• v.15 no.3
• /
• pp.251-262
• /
• 2009

In this research dairy cattle barn facilities what are 4,198 houses hold over 50 heads were surveyed by scale and province. Full-time farms hold over 50 heads breed total 344,514 heads. Each of Farms holds 50 to 99 heads were 79.8 percent and breed average 82.1 heads. Dairy cattle barns were constructed september 1995 averagely. Each of barns have $1,740.0\;m^2$ scale. The construction type of dairy cattle barn was almost litter barn type 84.0%, freestyle type 5.1%, mooring+litter ground type 17.3% and other types 4.4%. The litter barn type was popular in small farms. But in large farms, freestyle type was popular than small farms. The construction type of dairy cattle barn was almost litter barn type 84.0%, freestyle type 5.1%, moohng+ltter ground type 17.3% and other types 4.4%. Type of dairy cattle robotic milking system was pipeline 41.5%, herringbone 22.8% and tandem 35.8%. The pipeline type was popular in small farms which have 50~99 heads. But in large farms which have over 200 heads, tandem type was popular than small farms. Proportion of floor type of dairy cattle barn was almost litter type 94.9%. Scraper type was popular in large farms than in small farms. Proportion of roof type of dairy cattle barn was slate 32.5%, vinyl 16.3%, sunlight 11.1%, panel 10.9, zinc plate 8.8 and steel plate 8.3%. Roof type was lots of slate type before 1995. But vinyl type is increasing after 1995. Proportion of wall type of dairy cattle barn was almost open type 83.3% and winch-curtain 26.8%. Utilization period of dairy cattle barn was 9.2 years about milker, 7.9 years about automatic feeder, 9.2 years about waterer and 10.4 years about electric facilities. In this results, there were lots of improvements about automatic feeder.

• Journal of Satellite, Information and Communications
• /
• v.7 no.3
• /
• pp.30-34
• /
• 2012

National Meteorological Satellite Center(NMSC) of Korea Meteorological Administration(KMA) has launched to implement the application development to get prepared for the space weather operation since 2010. As a action of KMA's space weather work, NMSC constructed Global Navigation Satellite System(GNSS) application system for meteorology and space weather. We will introduce NMSC's space weather application system which derives regional TEC(Total Electron Content) in near real time using nation-wide GNSS network data. First, We constructed system for collecting GNSS data, which is currently collecting about 80 stations operated by agencies like NGII(National Geographic Information Institute), Central Office of DGPS(Differential GPS), and KASI(Korea Astronomy and Space Science) including KMA's own data of 2 stations. In order to retreive regional TEC over Korean peninsular, we build up the automatic processes running every 1-hour. In these processes, firstly, GNSS data of every stations with 24 hours time window are processed to derive DCBs(Differential Code Biases) of each GNSS station and TEC values on every ionosphere piercing point(IPP). Then we made gridded regional TEC map with resolution of 0.25 degree from 31N, 121E to 41N, 135E by combination of all station results within 30 minutes window with assumption that TEC of a given point during a given 30 minutes window would have a constant value. The grid points without TEC value are interpolated using Barnes objective analysis. We presentour regional TEC maps, which can describe better on the status of ionosphere over Korean peninsular compared to IGS TEC maps.

• Journal of Digital Convergence
• /
• v.12 no.9
• /
• pp.219-223
• /
• 2014

In line with the advanced wireless communication technology, M2M (Machine-to-Machine) communication has drawn attention in industry. M2M communication features are installed and operated in the fields where human accessibility is highly limited such as disaster, safety, construction, health and welfare, climate, environment, logistics, culture, defense, medical care, agriculture and stockbreeding. In M2M communication, machine replaces people for automatic communication and countermeasures as part of unmanned information management and machine operation. Wireless M2M inter-device communication is likely to be exposed to intruders' attacks, causing security issues, which warrants proper security measures including cross-authentication of whether devices are legitimate. Therefore, research on multiple security protocols has been conducted. The present study applied SessionKey, HashFunction and Nonce to address security issues in M2M communication and proposed a safe protocol with reinforced security properties. Notably, unlike most previous studies arguing for the security of certain protocols based on mathematical theorem proving, the present study used the formal verification with Casper/FDR to prove the safety of the proposed protocol. In short, the proposed protocol was found to be safe and secure.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.42-48
• /
• 2012

Due to increase in demand of stable and long pipelines in natural gas industry, wide range of researches are being performed on automation welding to improved welding quality with respect to weld process parameters in real time measurement. In particular, the coupling between the pipe manufacturing process and location of the weld seam, the measured size of the gap that exists in the weld position and the weld angle depending on whether the movement of molten weld. This is due to absence of controlling welding penetration position, depending on the required size of the angle of the setting. In addition, the optimum welding conditions must be considered while selecting, the correlation between these variables and the systematic correlation has not yet been identified. Therefore, in most welded pipe root-pass weld solely depends on the experience of workers in relation to secure a stable weld quality. In this study, automation welding system is implemented to select a suitable root-pass STT (Surface Tension Transfer) welding method using the optimal welding conditions. To successfully accomplish this objective, there were various welding conditions used for welding experiment to confirm that the assessment required for construction through the pipe and automatic welding process is proposed to optimize this plan.

• Korean Journal of Computational Design and Engineering
• /
• v.15 no.3
• /
• pp.212-221
• /
• 2010

Proposed in the paper is a methodology to generate kinematic template for 3D JIG models. Recently, according to increase of the rate of automatic facility in manufacturing system, the 3D manufacturing and verification research and development have been issued. So, unlike in the past, moving 3D facilities are very various like JIGs, turn table, AS/RS worked in the automated manufacturing industry. Because 3D mesh models are used in these kinds of 3D simulation, users have to define the kinematic information manually. This 3D mesh data doesn't have parametric information and design history of the 3D model unlike the design level data. So, it is lighter than 3D design level data and more efficient to render on the 3D virtual manufacturing environment. But, when user wants to find a common axis located between the links, the parameter information of the model has to reconstruct for defining kinematic construction. It takes a long time and very repetitive to define an axis and makes a joint using 3D mesh data and it is non-intuitive task for user. This paper proposed template model that provides kinematic information of the JIG. This model is kinds of a state diagram to describe a relation between links. So, this model can be used for a kinematic template to the JIG which has a same mechanism. The template model has to be registered in the template library to use in the future, after user made the model of the specific type of the 3D JIG model.