• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.275-277
• /
• 2005

In a lithium-ion battery which is being used in many portable electronic goods, electrolyte is disaggregated and then the gas is happened when electric charging volt is over the 4.5V. So, the pressure on the safety valve is increased and electrolyte is leaked out in the cell. It leads to the risk of explosion. On the other hand, in the case which the battery is discharged excessively, the negative pole is damaged and the performance of the battery is deteriorated. The protection module of a lithium-ion battery is used for preventing such risk and the inspection system is needed to check the performance of such protection module. In this research, a PC-based auto inspection system is developed for the inspection of a battery protection module using Dallas chipset. In the inspection system, AVRl28 chip is used as a controller and the communication protocol is developed for the data communication between the protection module and the AVR128 chip. And GPIB interface is used for the control of measuring devices. Also, MMI environment is developed using LabView for convenient monitoring by the tester.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.82-90
• /
• 2005

Recently, the in-line vision inspection has become the subject of growing research area in the visual control systems and robotic intelligent fields that are required exact three-dimensional pose. The objective of this article is to study the pc based in line visual inspection with the hand-eye structure. This paper suggests three dimensional structured light measuring principle and design method of laser sensor header. The hand-eye laser sensor have been studied for a long time. However, it is very difficult to perform kinematical analysis between laser sensor and robot because the complicated mathematical process are needed for the real environments. In this problem, this paper will propose auto-calibration concept. The detail process of this methodology will be described. A new thinning algorithm and constrained hough transform method is also explained in this paper. Consequently, the developed in-line inspection module demonstrate the successful operation with hole, gap, width or V edge.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.531-532
• /
• 2012

• 자동차안전학회지
• /
• 제16권1호
• /
• pp.42-48
• /
• 2024

With a sustained increase in the number of reported registrations for two-wheeled vehicles and the simultaneous growth of the domestic two-wheeled vehicle market, fueled by the activation of contactless industries and a rising population engaging in recreational two-wheeled vehicles during the COVID-19 era, concerns regarding safety incidents and environmental issues have come to the forefront. While the regular inspection methods and environmental standards for four-wheeled vehicles are becoming more stringent for safety and environmental management, the same cannot be said for two-wheeled vehicles. As the market for two-wheeled vehicles continues to expand, there is a pressing need for improvements in the management and inspection of these vehicles. In this study, we analyze cases of non-compliance from the results of periodic inspections over the past five years, specifically focusing on illegal customizations, exhaust emissions testing, and exhaust noise results. Through this analysis, we elucidate the necessity for enhancing the inspection system for two-wheeled vehicles, drawing parallels with the inspection systems applied to conventional automobiles. The findings of this research contribute to advocating for improvements in the inspection regime for two-wheeled vehicles, addressing the growing concerns related to safety and environmental impact.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.517-518
• /
• 2008

• 자동차안전학회지
• /
• 제13권1호
• /
• pp.51-56
• /
• 2021

As hydrogen is classified as an eco-friendly fuel, vehicles using hydrogen fuel are being developed worldwide. Vehicle fuel hydrogen is stored in cylinders at 70 MPa, so there is a high risk of explosion. Therefore, it is important to inspect hydrogen cylinders in used-vehicles. This study was conducted to improve the inspection method of the cylinders currently mounted on used-hydrogen buses. The inspection method is an image analysis method using a camera. Calcaulation algorithm was developed to quantitatively chech the amount of hydrogen leakage by the image method. As a result of adding a contact angle element to the calculation algorithm suggested by the GTR regulation and comparing it with the experimental data of the GTR regulation, the algorithm reliability was 94%, which secured similarity.

• 자동차안전학회지
• /
• 제10권2호
• /
• pp.43-49
• /
• 2018

Southeast Asia is a strategic market for both technology and inspection system to enter simultaneously. At the core market is Vietnam which is know to have the fourth highest registration of motorcycles as of 2016. The Motorcycle Inspection System is a social regulation, furthermore, the impact of the system is delivered through indirect means such as minimization of social cost. Therefore, measurements on the perception of users on the needs for an inspection system serves as valuable data to simultaneously enter this markets. This research is an empirical study on the perception of Vietnamese users on the needs to adopt a motorcycle inspection system based on data collected through surveys and is aimed at conducting a preliminary investigation on consumer behavior in Vietnam. The empirical study conducted through surveys revealed that Vietnamese motorcycle users perceive the needs for an inspection system for maintenance, safe operations and selling used vehicles at a reasonable price. In addition, the study also verified that the safe operations factor has a moderating effect due to interaction between prevention of illegal vehicle and reduction of emission gases. This research results present implications in developing equipment adapted to the local area in order to enter into a strategic market. Moreover, it is expected that the findings will also serve as valuable data for bilateral cooperation between the two countries and the diffusion of technology.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.212-218
• /
• 2000

The importance and role of pre-/in-service inspection(PSI/ISI) for nuclear power plant(NPP) components are intimately related to plant design, safety, reliability, operation, etc. In this paper, for an effective and efficient management of large amounts of PSI/ISI data in NPPs, an intelligent database program(WS-IDPIN) for PSI/ISI data management of NPP was developed. WS-IDPIN program enables the prompt extraction of previously conducted PSI/ISI conditions and results so that the time-consuming data management, painstaking data processing and analysis in the past are avoided. Furthermore, development of ISI UT auto flaw evaluation and acceptance module based on ASME Code Sec. XI were presented. This module can be used for any angle beam examination from flat plate to spherical shapes as selected by the proper azimuthal angle. This program can be further developed as a unique PSI/ISI data management expert system.

• 자동차안전학회지
• /
• 제5권2호
• /
• pp.57-61
• /
• 2013

A column for streetlamp has been damaged by severe wind loads such as typhoon. The stress concentration around the inspection hole may cause the collapse of the column for streetlamp. In this paper, the effects due to the wind load of 60 m/s and the car crash to the column at the speed of 48 km/h were considered to examine the design stability analysis of the column for streetlamp. The maximum von Mises stress did not exceed the yield stress of the material. Considering the car crash, the column for streetlamp was not collapsed.

• 소성∙가공
• /
• 제11권7호
• /
• pp.620-627
• /
• 2002

The purpose of this paper is the development of an automated measurement system for micro spring based on the digital image processing technique. This micro spring can be used in various engineering applications such as filament, load bearing springs, hard disk suspension and many others. Main functionality of the micro spring inspection system is to measure the representative pitch of the micro spring. The derivative operators are used for edge detection in gray level image. Measurement system developed in this paper consisted of new auto feeding mechanism to take advantage of air pressure. In the process of development of the micro spring inspection system based on the image processing and analysis, strong background technology and know-how have been accumulated to measure micro mechanical parts.