• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.945-952
• /
• 1998

Ferroelectric Sr0.8Bi2.4Ta2O9 stock solutions were prepared by MOD(Metaloganic Decompostion) process. The phase transformation for the layered perovskite of the SBT thin films by changing RTA(Rapid her-mal Annealing) temperatuer from 700$^{\circ}C$to 780$^{\circ}C$ were observed using XRD and SEM. Layered perovskite phase began to appear above 740$^{\circ}C$ and then SBT thin films were annealed at 800$^{\circ}C$ for 1hr for its com-plete crystallization. The specimens showed well shaped hysteresis curves without post annealing that car-ried out after deposition of Pt top electrode. The SBT thin films showed the asymmetric ferroelectric pro-perties. It was confirmed that the properties were caused by interface effect to SBT and electrode by leak-age current density measurement and asymmetric properties reduced by post annealing. At post annealing temperature of 800$^{\circ}C$ remanant polarization values (2Pr) were 6.7 9 ${\mu}$C/cm2 and those of leakage current densities were 3.73${\times}$10-7 1.32${\times}$10-6 A/cm2 at 3, 5V respectively. Also bismuth bonding types of SBT thin film surface were observed by XPS.

• Carbon letters
• /
• v.26
• /
• pp.11-17
• /
• 2018

Milled carbon fiber (mCF) was prepared by a ball milling process, and X-ray diffraction (XRD) diffractograms were obtained by a $2{\theta}$ continuous scanning analysis to study mCF crystallinity as a function of milling time. The raw material for the mCF was polyacrylonitrile-based carbon fiber (T700). As the milling time increased, the mean particle size of the mCF consistently decreased, reaching $1.826{\mu}m$ at a milling time of 18 h. The XRD analysis showed that, as the milling time increased, the fraction of the crystalline carbon decreased, while the fraction of the amorphous carbon increased. The (002) peak became asymmetric before and after milling as the left side of the peak showed an increasingly gentle slope. For analysis, the asymmetric (002) peak was deconvoluted into two peaks, less-developed crystalline carbon (LDCC) and more-developed crystalline carbon. In both peaks, Lc decreased and $d_{002}$ increased, but no significant change was observed after 6 h of milling time. In addition, the fraction of LDCC increased. As the milling continued, the mCF became more amorphous, possibly due to damage to the crystal lattices by the milling.

• Journal of Korean Association for Spatial Structures
• /
• v.2 no.4 s.6
• /
• pp.61-76
• /
• 2002

The structure system that is discreterized by continuous shells is usually used to make a large space structures and these structures show the collapse mechanisms that are captured at over the limit load, and snap-through and bifurcation are most well known of it. For the collapse mechanism, rise-span ratio, element stiffness and load mode are main factor, which it give an effect to unstable behavior. Moreover, resist force of structure can be reduced by initial condition and initial imperfection significantly. In order to investigate the instability of shell structures, the finite deformation theory can be applied and it becomes a nonlinear mathematics in which use equation of tangential stiffness incrementally. With an initial imperfection, using simple example and Flow Truss Dome, the buckling characteristics of space truss is main purpose of this paper, and unstable behavior is studied by proposed the numerical method. Also, by using MIDAS, this research work analyzes displacements and inner forces as the design load of model, and the ratio of buckling load of design load is investigated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1022-1027
• /
• 2007

This paper presents a method to analyze the unbalance response of a high speed polygon mirror scanner motor supported by sintered metal bearing and flexible structures by using the finite element method and the mode superposition method considering the asymmetry of the gyroscopic effect and sintered metal bearing. The eigenvalues and eigenvectors are calculated by solving the eigenvalue problem and the adjoint eigenvalue problem by using the restarted Arnoldi iteration method. The decoupled equations of motion can be obtained from global finite element motion equations by using the orthogonal relation between the right eigenvectors and left eigenvectors. The decoupled equations of motion are used to analyze the unbalance response of a high speed polygon mirror scanner motor. The validity of the proposed method is verified by comparing the simulated unbalance response with the experimental results.

• Transactions of Materials Processing
• /
• v.29 no.1
• /
• pp.5-10
• /
• 2020

Heat treatment conditions of 88.5% asymmetrically cold rolled oxygen free copper (OFC) sheets have been studied to obtain an equiaxed fine microstructure with a grain size of less than 10 ㎛. The commercial OFC sheets with the thickness of 10 mm were asymmetrically cold rolled by using equal speed asymmetric rolling (ESAR) processes and total rolling reduction. The thickness of the rolled sheets were 88.5% and 1.15 mm, respectively. An equiaxed fine microstructure of OFC sheets with a grain size of 6.0 ㎛ were obtained when the asymmetrically cold rolled OFC sheets were heat treated at 180℃ for 40 minutes. The tensile strength of the asymmetrically cold rolled specimen increased from 217.6 MPa to 396.1 MPa, while the elongation of the specimen asymmetrically cold rolled and heat treated increased from 29.0% to 66.9% along with an 8% increase of the tensile strength.

• Bulletin of the Korean Space Science Society
• /
• 2011.04a
• /
• pp.28.3-28.3
• /
• 2011

Halo coronal mass ejections (HCMEs) are mainly responsible for the most severe geomagnetic storms. To minimize the projection effect of the HCMEs observed by coronagraphs, several cone models have been suggested. These models allow us to determine the geometrical and kinematic parameters of HCMEs : radial speed, source location, angular width, and the angle between the central axis of the cone and the plane of the sky. In this study, we compare these parameters form two representative cone models (the ice-cream cone model and the asymmetric cone model) using well-observed HCMEs from 2001 to 2002. And we obtain the root mean square error (rms error) between observed projection speeds and calculated projection speeds for both cone models. It is found that the average rms speed error (89 km/s) of the asymmetric cone model is a little smaller than that (107 km/s) of the ice-cream cone models, implying that the radial speeds from both models are reasonably estimated. We also find that the radial speeds obtained from two models are similar to each other with the correlation coefficient of about 0.8.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.39-39
• /
• 2003

The plasmaspheric region shows relatively strong longitudinal asymmetry in the sense that the location of the plasmapause and the density distribution significantly vary with respect to local time, and this asymmetry effect has been neglected in previous magnetospheric ULF wave studies. In this study, we numerically examine the MHD wave properties of field line resonances (FLRs) and Pi2 pulsations when the inner magnetosphere is assumed to be asymmetric. We use the dipole magnetic field model, but our density model is based on. observational data from the IMAGE satellite. We assume an impulsive input in the magnetotail, which can be associated with a substorm onset. Our results suggest that local FLRs appear in both the radial and azimuthal oscillations owing to the asymmetry. Plasmaspheric Pi2 signals appear in the compressional component, but they are more strongly affected by ambient plasmaspheric structure than the FLRs. We compare our results with the observational data of Pi2 events.

• Journal of The Korean Astronomical Society
• /
• v.44 no.3
• /
• pp.97-108
• /
• 2011

The photometric light curves of the W-type W UMa eclipsing contact binary system BB Pegasi have been found to be extremely asymmetric over all the observed 63 years in all wavelengths UBVR. The light curves have been characterized by occultation primary minima. Hence, the morphology of these light curves has been studied in view of these different asymmetric degrees. The system shows a distinct O'Connell effect, as well as depth variation. A 22.96 years of stellar dark spots cycle has been determined for the system. Almost the same cycle (22.78 yr) has been found for the depth variation of MinI and MinII. We also present an analysis of mid-eclipse time measurements of BB Peg. The analysis indicates a period decrement of $5.62{\times}10^{-8}$ day/yr, which can be interpreted in terms of mass transfer at a rate of $-4.38{\times}10^{-8}M_{\odot}$/yr, from the more to the less massive component. The O - C diagram shows a damping sine wave covering two different cycles of 17.0 yr and 12.87 yr with amplitudes equal to 0.0071 and 0.0013 day, respectively. These unequal durations show a non-periodicity which may be explained as a result of magnetic activity cycling variations due to star spots. The obtained characteristics are consistent with similar chromospherically active stars, when applying the Applegate's (1992) mechanism.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.9
• /
• pp.839-846
• /
• 2014

Recent trends in the miniaturization and weight reduction of portable electronic parts have driven the use of subminiature screws with a micrometer-scale pitch. As both screw length and pitch decrease in subminiature screws, the resulting clamping force becomes diminishes. In this work, Finite element (FE) analysis is performed to evaluate clamping force of a screw assembly, with a comparison with experimental result. To improve clamping force of subminiature screws, a new screw design is considered by modifying screw thread angle: the thread angle is varied as an asymmetric way unlike the conventional symmetric thread angle. FE analyses are then performed to compare the clamping characteristics of each subminiature screw with different thread angle. The effect of thread angles on the clamping force is then discussed in terms of structural safety for both positive and negative screws.

• Journal of IKEEE
• /
• v.11 no.3
• /
• pp.95-99
• /
• 2007

In this study, the electrical characteristics of Symmetric and Asymmetric High Voltage MOSFET(HV-MOSFET) under high temperature were investigated. And, the specific on-resistance, threshold voltage, transconductance, drain current of the HV-MOSFETs were measured over a temperatures range of 300K ${\leq}$ T ${\leq}$400K. From the result of measured data, specific on-resistance increases slightly with increasing temperature. Especially, at high temperature(at 400K) specific on-resistance was increased about 30% than that in room temperature. And, in high temperature condition (at 400K), drain current was decreased about 30%, Also, transconductance(gm) was decreases with increasing temperature.