• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.583-586
• /
• 2017

마이크로 터보제트엔진을 이용하여 S형상 배기노즐의 플룸의 적외선 신호 특성을 이해하기 위하여 적외선 신호 특정 연구를 수행하였다. 엔진 배기노즐은 원형노즐과 가로세로비가 5인 사각형 노즐 그리고 가로세로비가 5.2인 S형상의 배기노즐을 제작하여 실험을 수행하였다. 배기가스에서 방출되는 적외선 신호는 가로세로비가 클수록 적외선 신호의 크기가 점차 감소하는 경향을 보였고 배기노즐의 형상이 S형상의 경우 사각형 노즐 보다 적외선 신호가 28.4% 감소하는 것을 확인하였다.

• 동력기계공학회지
• /
• 제13권5호
• /
• pp.11-17
• /
• 2009

A numerical study of unsteady mixed convection in a cavity with high viscous fluid is presented. Finite volume method was employed for the discretization and PISO algorithm was used for calculating pressure term. The parameters governing the problem are the Rayleigh number ($10^3\;{\leq}\;Ra\;{\leq}\;10^5$), the Reynolds number (0 < Re $\leq$ 1), and the aspect ratio (0.5 $\leq$ AR $\leq$ 2). The fluid used is silicon oil, a high prandtl number fluid, Pr = 909.1. The results show velocity vectors and temperature distributions. It is found that the periodic flows in a cavity are observed at very low Reynolds numbers, and the period of periodic flow decreases with increasing Reynolds and Rayleigh numbers, and increases with increasing aspect ratio. Also, the Reynolds number range of periodic flow increases with increasing Rayleigh numbers and aspect ratio.

• 한국정밀공학회지
• /
• 제29권12호
• /
• pp.1272-1278
• /
• 2012

The micro barrier rip array structures have been applied in a variety of areas including as privacy films, micro heat sinks, touch panel and optical waveguide. The increased aspect ratio (AR) of barrier rip array structures is required in order to increase the efficiency and performance of these products. There are several problems such as burr, defect of surface roughness and deformation and breakage of barrier rip structure with machining high-aspect ratio micro barrier rip array structure using orthogonal cutting method. It is essential to develop technological methods to solve these problems. The optimum machining conditions for machining micro barrier rip array structures having high-aspect ratio were determined according to lengths ($200{\mu}m$ and $600{\mu}m$) and shape angles ($2.89^{\circ}$ and $0^{\circ}$) of diamond tool, overlapped cutting depths ($5{\mu}m$ and $10{\mu}m$), feed rates (100 mm/s) and three machining processes. Based on the optimum machining conditions, micro barrier rib array structures having aspect ratio 30 was machined in this study.

• Composites Research
• /
• 제20권6호
• /
• pp.28-33
• /
• 2007

단섬유 강화고무의 관통 특성에 대해 섬유 종횡비(AR: 섬유 길이/섬유 직경), 섬유 함유량, 시편 크기 그리고 시험속도를 변수로 하여 연구하였다. 기지와 단섬유 강화고무의 관통 저항은 시편 크기의 증가에 따라 감소하였고, 동일한 시편 크기에서 시험 속도의 증가에 따라 관통 저항력은 증가하였다. 각각의 섬유 함유량에서 섬유 종횡비가 클수록 높은 관통응력 값을 보였다. 인장강도와 관통응력의 비교를 통해 시편 형상의 문제점에 대해 고찰하였다. 기지와 단섬유 강화고무의 막에 작용하는 힘은 시편의 크기에 관계없이 유사한 값을 보였고, 동일한 시편 크기에서 시험속도의 증가에 따라 증가하였다. 각각의 섬유함유량에서 섬유 종횡비가 클수록 막에 작용하는 힘은 크게 나타났다 전체적으로 시편 크기, 시험속도가 단섬유 강화고무의 관통 특성에 지대한 영향을 미침을 확인하였다.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2160-2170
• /
• 1991

본 연구에서는 날카로운 모서리를 가진 타원제트(AR=2)의 근접 영역에서 제트 의 난류구조 및 축교차현상을 3-D LDV 시스템을 이용하여 조사하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.733-736
• /
• 2002

As composite materials, the addition of steel fiber in concrete significantly improves the engineering properties of structural members. The purpose of this study is to define the strengthening effect of steel fiber in a point of material usage. From tile material test. compression strength, tensile splitting strength and flexural strength were evaluated by steel fiber volume fraction ($V_f$) and aspect ratio (AR) of steel fiber. In case of AR 67, $V_f$ 2.0% could be achieved maximum steel fiber strengthening effect. And the AR 80 case, $V_f$ 1.0% could be achieved maximum effect than the effect of $V_f$ 1.5%.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.1001-1003
• /
• 1998

In this paper, $Ar^+$ ion laser etching process of single/poly crystalline silicon with $CCl_{2}F_{2}$ gas is studied for MEMS applications. To investigate the effects of process parameters, laser power, gas pressure, scanning speed were varied and multiple scanning was carried out to obtain high aspect ratio. In addition, scanning width was varied to observe the trench profile etched in repeating scanning cycle. From the etching of $2.6{\mu}m$ thick polycrystalline Si deposited on insulator, trench with flat bottom and vertical side wall was obtained and it is possible to apply this results for MEMS applications.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권7호
• /
• pp.668-673
• /
• 1997

A Single-crystalline Mn-Zn Ferrite (110 orientation) was masklessly etched by focused Ar laser irradiation in an H$_3$PO$_4$ solution. The depth of the etched grooves increases with increasing a laser power, decreasing a scan speed, and increasing the H$_3$PO$_4$concentration. The width of the etched grooves increases with a increasing laser power, but was relatively insensitive to the scan speed and H$_3$PO$_4$concentration. High etching rate of up to 714 ${\mu}{\textrm}{m}$/s and an aspect ratio of 6 for vertical slab structure have been obtained by the light-guiding effect of the laser bean in the H$_3$PO$_4$ solution.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.284-284
• /
• 2011

Recently, the increasing degree of device integration in the fabrication of Si semiconductor devices, etching processes of nano-scale materials and high aspect-ratio (HAR) structures become more important. Due to this reason, etch selectivity control during etching of HAR contact holes and trenches is very important. In this study, The etch selectivity and etch rate of TEOS oxide layer using ACL (amorphous carbon layer) mask are investigated various process parameters in CH2F2/C4F8/O2/Ar plasma during etching TEOS oxide layer using ArF/BARC/SiOx/ACL multilevel resist (MLR) structures. The deformation and etch characteristics of TEOS oxide layer using ACL hard mask was investigated in a dual-frequency superimposed capacitively coupled plasma (DFS-CCP) etcher by different fHF/ fLF combinations by varying the CH2F2/ C4F8 gas flow ratio plasmas. The etch characteristics were measured by on scanning electron microscopy (SEM) And X-ray photoelectron spectroscopy (XPS) analyses and Fourier transform infrared spectroscopy (FT-IR). A process window for very high selective etching of TEOS oxide using ACL mask could be determined by controlling the process parameters and in turn degree of polymerization. Mechanisms for high etch selectivity will discussed in detail.

• Wind and Structures
• /
• 제30권5호
• /
• pp.525-532
• /
• 2020

This work numerically investigates the effects of Reynolds number Re_D (= 100 - 150), cross-sectional aspect ratio AR = ( 0.25 -1.0), and attack angle α (= 0° - 90°) on the forces, Strouhal number, and wake of an elliptical cylinder, where Re_D is based on the freestream velocity and cylinder cross-section height normal to the freestream flow, AR is the ratio of the minor axis to the major axis of the elliptical cylinder, and α is the angle between the cylinder major axis and the incoming flow. At Re_D = 100, two distinct wake structures are identified, namely 'Steady wake' (pattern I) and 'Karman wake followed by a steady wake (pattern II)' when AR and α are varied in the ranges specified. When Re_D is increased to 150, an additional wake pattern, 'Karman wake followed by secondary wake (pattern III)' materializes. Pattern I is characterized by two steady bubbles forming behind the cylinder. Pattern II features Karman vortex street immediately behind the cylinder, with the vortex street transmuting to two steady shear layers downstream. Inflection angle α_i = 32°, 37.5° and 45° are identified for AR = 0.25, 0.5 and 0.75, respectively, where the wake asymmetry is the greatest. The α_i effectively distinguishes the dependence on α and AR of force and vortex shedding frequency at either Re_D. In Pattern III, the Karman street forming behind the cylinder is modified to a secondary vortex street. At a given AR and α, Re_D = 150 renders higher fluctuating lift and Strouhal number than Re_D = 100.