• 산업기술연구
• /
• 제19권
• /
• pp.59-65
• /
• 1999

This study is to analyze turbulent flow over a backward-facing step in a rectangular duct. The side wall effects on the internal flow were determined by varying the aspect ratio(defined as the step span-to-height ratio) from 1 to 20. In the flow behind a backward-facing step, separation, recirculation and redeveloping is occurred frequently. These phenomena appear in a particular variation by varying the aspect ratio. The results show that the aspect ratio has an influence on the velocity and reattachment length. When the AR is increased, the reattachment length is increased. For 6 over aspect ration, the rate of increase is decreased. The length of recirculation in the upper corner is increased, as the increase of aspect ration. It's width is not changed in the variation of aspect ration. The transverse, streamwise and spanwise velocities were decreased along the flow down stream of the step.

• 한국농공학회지
• /
• 제41권3호
• /
• pp.73-80
• /
• 1999

The objective of this study were to investigate the properties and to improve the disadvantages of the polymer concrete such as brittle fracture, large hardening shrinkage . In this paper, steel fiber reinforced polymer concrete is prepared with various steel fiber aspect ratios(ι/d), contents(vol.%), and their material characteristics were investigated experimentally . The aspect ration (ι/d) of the steel fiber was reversly proportional to slump value, and slump value tended to decrease as increase of steel fiber content . And harding shrinkage and impact resistance tended to be improved as the steel fiber content and aspect ration were increased.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.214-220
• /
• 1999

In order to use effectively a machinery part with fillet, it is necessary to determine a proper fillet shape in design step, Study of such problem by fracture mechanical criterion is rare. So, this paper focuses on the design of fillet radius in fracture mechanical aspect. Finite element method was used to obtain crack tip stress intensity factor. Stress intensity factor was calculated by COD(crack opening displacement0method proposed by Ingraffea and Manu. The parameter used in this study are thickness ration, filet radium and crack length . If fillet radius increase , crack propagation may be accelerated. Critical crack length is inversely proportional to fillet radius.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.54-61
• /
• 1995

Simultaneous forward-backward extrusion upsetting has been carried out by ratray forging. Two materials has been used commericaly 6.61 aluminium ally and 0.2% steel. The effects of working conditions ; spiral feed ; initial aspect ration of specimen and lubricating condition on the backward and forward extrusion were clarified. The extrusion length increases a sthe aspect rationof the specimen increases, the backward extrusion lengthbeing relatively larger than the forward one. The effects of the spiral feed and the material on the extrusion lengthis remarkably large for the large spiral feed.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2006년도 하계학술발표회 논문집
• /
• pp.553-554
• /
• 2006

• 한국광학회:학술대회논문집
• /
• 한국광학회 2006년도 하계학술발표회 논문집
• /
• pp.551-552
• /
• 2006

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.403-407
• /
• 2009

It is reported that the heavy weight floor impact noise of a slab system is very sensitive to the location of microphone and impact load. In addition, it is known that the aspect raio, thickness and boundary condition of a slab also have great effect on the noise induced by impact load. However, the effect has been mainly evaluated by experimental test and numerical analysis is nearly performed to verify the effect quantitatively. In this study, the effect of the aspect ratio, thickness and boundary condition on the heavy weight floor impact noise is examined through numerical analysis for simple rectangular slab system. The results show that the thickness and boundary condition have a strong correlation with the noise of the slab, on the contrary, the aspect ratio has little relation with the noise.

• 전기학회논문지
• /
• 제60권6호
• /
• pp.1134-1139
• /
• 2011

When the aspect ratio of a magnet varies, the magnetic field in the magnet also varies. The critical current of a tape-shaped HTS wire varies with the direction and magnitude of applied magnetic field. Consequently when the aspect ration of a HTS magnet varies, the critical current of a HTS magnet varies. This paper shows the relation between the aspect ratio of a magnet and the energy and inductance of a HTS magnet. The critical current is also shown at various aspect ratio of the magnet. The length of the HTS wire, inner diameter of the magnet, and number of pancake are chosen to be variables which varies the shape of the magnet. For a HTS magnet consisting of pancake windings, calculation results show the number of pancake windings are the prime factor which varied the energy and inductance of the magnet. The inner diameter of the magnet varies the energy and inductance of the magnet a little.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.233-237
• /
• 1995

Effects of frictional laws on finite element solutions in bulk metal forming were investigated in this paper. The Coulomb friction and the constant shear friction law were compared through finite element anlayses of compression of ring and cylinders with different aspect rations, ring-gear forging and hot strip rollin under the isothermal condition. It has been shown that two laws may yield quite different results inthe case that the aspect ration of a process is large, for example , strip rolling and ring -gear forging and that the difference depends mainly on the aspect ratio and the friction.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1522-1527
• /
• 2004

The purpose of this study is to investigate the effect of swirler angle and swirl chamber aspect ration of nozzle on the characteristics of single and twin spray. The performances of nozzle has been investigated by measurements of spray angle, droplet size, velocity and Weber number at a water pressure 0.4MHz. Visualization of spray was conducted to obtain the spray angle and breakup process. The spray characteristics such as droplet size and velocity were measured by Phase Doppler Anemometry(PDA). It was found that the smaller swirler angle, the larger axial velocity became. It was also shown that the larger aspect ratio, the smaller droplet diameter became.