• Journal of Industrial Technology
• /
• v.19
• /
• pp.59-65
• /
• 1999

This study is to analyze turbulent flow over a backward-facing step in a rectangular duct. The side wall effects on the internal flow were determined by varying the aspect ratio(defined as the step span-to-height ratio) from 1 to 20. In the flow behind a backward-facing step, separation, recirculation and redeveloping is occurred frequently. These phenomena appear in a particular variation by varying the aspect ratio. The results show that the aspect ratio has an influence on the velocity and reattachment length. When the AR is increased, the reattachment length is increased. For 6 over aspect ration, the rate of increase is decreased. The length of recirculation in the upper corner is increased, as the increase of aspect ration. It's width is not changed in the variation of aspect ration. The transverse, streamwise and spanwise velocities were decreased along the flow down stream of the step.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.3
• /
• pp.73-80
• /
• 1999

The objective of this study were to investigate the properties and to improve the disadvantages of the polymer concrete such as brittle fracture, large hardening shrinkage . In this paper, steel fiber reinforced polymer concrete is prepared with various steel fiber aspect ratios(ι/d), contents(vol.%), and their material characteristics were investigated experimentally . The aspect ration (ι/d) of the steel fiber was reversly proportional to slump value, and slump value tended to decrease as increase of steel fiber content . And harding shrinkage and impact resistance tended to be improved as the steel fiber content and aspect ration were increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.7
• /
• pp.214-220
• /
• 1999

In order to use effectively a machinery part with fillet, it is necessary to determine a proper fillet shape in design step, Study of such problem by fracture mechanical criterion is rare. So, this paper focuses on the design of fillet radius in fracture mechanical aspect. Finite element method was used to obtain crack tip stress intensity factor. Stress intensity factor was calculated by COD(crack opening displacement0method proposed by Ingraffea and Manu. The parameter used in this study are thickness ration, filet radium and crack length . If fillet radius increase , crack propagation may be accelerated. Critical crack length is inversely proportional to fillet radius.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.54-61
• /
• 1995

Simultaneous forward-backward extrusion upsetting has been carried out by ratray forging. Two materials has been used commericaly 6.61 aluminium ally and 0.2% steel. The effects of working conditions ; spiral feed ; initial aspect ration of specimen and lubricating condition on the backward and forward extrusion were clarified. The extrusion length increases a sthe aspect rationof the specimen increases, the backward extrusion lengthbeing relatively larger than the forward one. The effects of the spiral feed and the material on the extrusion lengthis remarkably large for the large spiral feed.

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.07a
• /
• pp.553-554
• /
• 2006

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.07a
• /
• pp.551-552
• /
• 2006

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.403-407
• /
• 2009

It is reported that the heavy weight floor impact noise of a slab system is very sensitive to the location of microphone and impact load. In addition, it is known that the aspect raio, thickness and boundary condition of a slab also have great effect on the noise induced by impact load. However, the effect has been mainly evaluated by experimental test and numerical analysis is nearly performed to verify the effect quantitatively. In this study, the effect of the aspect ratio, thickness and boundary condition on the heavy weight floor impact noise is examined through numerical analysis for simple rectangular slab system. The results show that the thickness and boundary condition have a strong correlation with the noise of the slab, on the contrary, the aspect ratio has little relation with the noise.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.6
• /
• pp.1134-1139
• /
• 2011

When the aspect ratio of a magnet varies, the magnetic field in the magnet also varies. The critical current of a tape-shaped HTS wire varies with the direction and magnitude of applied magnetic field. Consequently when the aspect ration of a HTS magnet varies, the critical current of a HTS magnet varies. This paper shows the relation between the aspect ratio of a magnet and the energy and inductance of a HTS magnet. The critical current is also shown at various aspect ratio of the magnet. The length of the HTS wire, inner diameter of the magnet, and number of pancake are chosen to be variables which varies the shape of the magnet. For a HTS magnet consisting of pancake windings, calculation results show the number of pancake windings are the prime factor which varied the energy and inductance of the magnet. The inner diameter of the magnet varies the energy and inductance of the magnet a little.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.233-237
• /
• 1995

Effects of frictional laws on finite element solutions in bulk metal forming were investigated in this paper. The Coulomb friction and the constant shear friction law were compared through finite element anlayses of compression of ring and cylinders with different aspect rations, ring-gear forging and hot strip rollin under the isothermal condition. It has been shown that two laws may yield quite different results inthe case that the aspect ration of a process is large, for example , strip rolling and ring -gear forging and that the difference depends mainly on the aspect ratio and the friction.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1522-1527
• /
• 2004

The purpose of this study is to investigate the effect of swirler angle and swirl chamber aspect ration of nozzle on the characteristics of single and twin spray. The performances of nozzle has been investigated by measurements of spray angle, droplet size, velocity and Weber number at a water pressure 0.4MHz. Visualization of spray was conducted to obtain the spray angle and breakup process. The spray characteristics such as droplet size and velocity were measured by Phase Doppler Anemometry(PDA). It was found that the smaller swirler angle, the larger axial velocity became. It was also shown that the larger aspect ratio, the smaller droplet diameter became.