• International Journal of Industrial Entomology and Biomaterials
• /
• v.20 no.2
• /
• pp.99-105
• /
• 2010

In this paper, the regenerated silk fibroins were dissolved in LiBr aqueous solution with different dissolution temperature and time, and the effects of the dissolution condition on the regeneration yield, molecular weight, wet spinnability, and electrospinnability of regenerated silk fibroin were investigated. The regeneration yield, molecular weight distribution, and wet spinnability of regenerated silk fibroin were nearly affected by the dissolution temperature and time. However, the electrospinning performance of silk fibroin was influenced by the dissolution condition implying the electrospinning of silk fibroin is more sensitive process than the wet spinning in the range tested in this study. While $25^{\circ}C$ of dissolution temperature resulted in a good electrospinnability of regenerated silk fibroin, the electrospinnability was slightly deteriorated when silk fibroin was dissolved at $60^{\circ}C$ for 6 hours. Also, though the fiber diameters of electrospun silk fibroin produced by the dissolution at $25^{\circ}C$ for 6 hours and 24 hours were 443 and 451 nm, respectively, that at $60^{\circ}C$ for 5 min was reduced to 411 nm. The fiber diameter was more decreased to 393 nm when the dissolution time increased up to 6 hours at $60^{\circ}C$.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.132-137
• /
• 2006

Supercooled type ice slurry system is hard to keep a proper supercooling degree when solution becomes supercooling state. This is the reason of the ice blockage in pipe or cooling part due to an unstable cooling state. In this study, a cooling experiment was performed to pressurized solution in a stationary state. The behaviors during the supercooled aqueous solution were investigated at fixed flow rate of brine and aqueous solution of ethylene glycol 7 mass%. Also the effect to the freezing point of supercooled aqueous solution was investigated to the different pressure 101, 202, 303, and 404 kPa. At results, the pressure of the aqueous solution in the cylinder increased the supercooling degree increased and dissolution of supercooled point decreased.

• Journal of Korean Society on Water Environment
• /
• v.29 no.2
• /
• pp.176-183
• /
• 2013

The variation of the stable region of arsenic compounds in aqueous environment with temperature has been investigated by constructing the Pourbaix diagram of arsenic at different temperatures. The standard potential corresponding to the boundary between arsenic compounds with different charge valence was estimated to be decreased with temperature, which means the stability of arsenic compound with +5 charge valence increases. The distribution diagram of the most highly oxidized arsenic compound showed that arsenic acid is formed at higher pH and arsenate is generated at lower pH as temperature rises. The aquatic toxicity due to arsenic compounds was considered to be decreased with temperature in the neutral pH condition based on the $LD_T$ value defined in this study.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.23 no.1
• /
• pp.183-186
• /
• 2011

The various molecular weight (MW) regenerated silk fibroins were prepared with different dissolution condition and the effect of MW on the gelation behavior of regenerated aqueous silk fibroin (SF) solution was investigated. The result of gelation time measurement indicated that the gelation of SF aqueous solution was accelerated by the increase of MW and SF concentration. When formic acid was added in SF aqueous solution, the gelation time of SFL and SFC30 aqueous solution showed a significant decreaseat 0.03% formic acid addition. In case of the lowest MW sample, SFC180, SF molecules became aggregated and precipitated without gelation after 28 days storage time. These findings indicate that MW control of SF can be utilized to control the gelation time of SF aqueous solution.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.706-710
• /
• 2012

The growing conditions of barium nitrate $Ba(NO_3)_2$ single crystals using the aqueous solution method have been studied. Supersaturation can be calculated by measuring the temperature of the solution and its equilibrium temperature. Supersaturation of $Ba(NO_3)_2$ was 0.7% at $32.0^{\circ}C$ and about 3% at $34.0^{\circ}C$. The obtained single crystals have three kind of morphology: tetrahedral, cubic, and, rarely, dodecahedral. The normal growth rate is proportional to the supersaturation; it is necessary to make the solution below 5% supersaturation in order to obtain transparent $Ba(NO_3)_2$ single crystals. The normal growth rate for {1$\bar{1}$1} faces was $2.51{\times}10^{-6}$ mm/s for the 0.7% supersaturation condition ($32.0^{\circ}C$), $6.43{\times}10^{-6}$ mm/s for the the condition of 3.0% supersaturation, and $7.01{\times}10^{-6}$ mm/s for the condition of 5.0% supersaturation. The quality of the grown crystals depends on the nature of the seed, the cooling rate employed, and the agitation of the solution. The faces of the obtained crystals have been identified uising an X-ray diffractometer. The surface diffusion is responsible for the low growth rates of the {1$\bar{1}$1} faces.

• Journal of Power System Engineering
• /
• v.15 no.4
• /
• pp.42-47
• /
• 2011

The purpose of this study is to investigate the best melting condition with various winding number of a heating pipe, supplying quantity of engine coolant and coolant temperature at the inlet of the heating pipe. Also, it is to suggest getting method of an appropriate quantity of the agent for the urea-SCR system within 10 minutes. For this matter, this study identifies the temperature distribution of inside of urea-tank while it is frozen at the low temperature condition, and suggests the best melting condition of the frozen urea within 10 minutes. From the results, it was found that 2L of melted urea was obtained by the coolant flow rate of 200L/hr at $70^{\circ}C$ for 10 minutes from the start of engine operating.

• Corrosion Science and Technology
• /
• v.7 no.1
• /
• pp.61-67
• /
• 2008

In this paper, electrochemical and microstructural characteristics of nickel-plated Alloy 600 were investigated in order to identify the performance of electroless Ni-plating on Alloy 600 in high-temperature aqueous condition with the comparison of electrolytic nickel-plating. For high temperature corrosion test of nickel-plated Alloy 600, specimens were exposed for 770 hours to typical PWR primary water condition. During the test, open circuit potentials (OCP's) of all specimens were measured using a reference electrode. Also, resistance to flow accelerated corrosion (FAC) test was examined in order to check the durability of plated layers in high-velocity flow environment at high temperature. After exposures to high flow rate aqueous condition, the integrity of surfaces was confirmed by using both scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). For the field application, a remote process for electroless nickel-plating was demonstrated using a plate specimen with narrow gap on a laboratory scale. Finally, a practical seal design was suggested for more convenient application.

• Particle and aerosol research
• /
• v.13 no.3
• /
• pp.127-132
• /
• 2017

In this paper, the effect of the irradiation of the median-frequency of ultrasonic wave on the aqueous solution have been investigated. In addition, the decomposition ability of radical species was observed using phytoncide oil of 0.1 wt %. By observing the degree of decomposition while maintaining magnetic stirring, the unirradiated aqueous solution maintained turbid condition and the particle size of the oil was the same as the initial size. On the other hand, the irradiated aqueous solution presented that the transparency degree became good after 3 days and became to the same as the original purified water after one week. The particle size of the after 3 days was about 0.1 to $0.5{\mu}m$. From these results it could be demonstrated that when a medium frequency (about 400 kHz) is applied to the aqueous solution, decomposition ability of radical species are formed and the medium frequency irradiation system can be possible to purify the turbid aqueous solution.

• Journal of the Korean Ceramic Society
• /
• v.22 no.5
• /
• pp.71-75
• /
• 1985

This study deals with sintering and corrosive behavior of sintered zircons mixed with 5wt% of clay $Cr_2O_3$ $CrO_3-MgO$ aqueous solution and $CrO_3-Mg(OH)_2$ aqueous solution. Measurements were conducted by firing specimens at 135$0^{\circ}C$ 145$0^{\circ}C$ and 155$0^{\circ}C$ 1$650^{\circ}C$ for 3hrs in oxidized and reduced atmospheric conditions. Following results were obtained. 1. Sintered zircon with 5 wt% clay showed that highest compressive strength and the lowest apparent porosity and the other showed less positive result than above specimen in order of zircon with $CrO_3-MgO$ aqueous solution $CrO_3-Mg(OH)_2$ aqueous solution and $Cr_2O_3$. 2. The more firing temperature increased the more its strength improved and porosity decreased and specimen which was fired over 155$0^{\circ}C$ and in reduced atmospheric condition showed better results. 3. Zircon with additives which was fired over 155$0^{\circ}C$ showed the evidence of thermal dissociation but it was not rebonded completely during cooling. 4. Zircon with $CrO_3-MgO$ aqueous solution and $CrO_3-Mg(OH)_2$ aqueous solutiion showed more corrosive resistance than zircon itself and zircon-clay system.

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.775-780
• /
• 2014

Micellar enhanced ultrafiltration (MEUF) was used to remove cadmium from an aqueous solution using sodium dodecyl sulfate (SDS) as a surfactant. Operational parameters such as initial permeate flux, retentate pressure, initial cadmium concentration, pH solution, molecular weight cut-off (MWCO), and molar ratio of cadmium to SDS were investigated. Removal efficiency of cadmium from an aqueous solution increased with an increase of retentate pressure, pH solution and molar ratio of cadmium to SDS, and decreased with an increase of initial permeate flux. Higher removal efficiency of cadmium from the aqueous solution was achieved using lower MWCO (smaller membrane pore size). Under optimized experimental condition, cadmium removal efficiency reached 74.6 % within an hour. Using MEUF-ACF hybrid process the removal efficiency of both cadmium and SDS was found to be over 90%.