• Journal of electromagnetic engineering and science
• /
• 제8권1호
• /
• pp.1-5
• /
• 2008

In this paper, a biconical type antenna is proposed for EMI test site validation above 1 GHz. To achieve broadband and omni-directional radiation patterns required by international standard(CISPR), the proposed antenna consists of general bicones with cylindrical loads and adopts side feeding method to minimize the influence on H-plane pattern due to feeding cable, balun, and connector. The radiation patterns of the fabricated antenna are measured and the results are compared with CISPR criteria and commercial antenna in our interest frequencies. Although the proposed antenna has a few problems in frequency range of 1 GHz to 2 GHz, it has relatively better performance than commercial antenna.

• 한국전자파학회논문지
• /
• 제13권10호
• /
• pp.1061-1070
• /
• 2002

본 논문은 IS2000 환경에서 기지국의 수신 성능을 증대시키기 위한 스마트 안테나 Test-bed의 성능을 분석하였다. 따라서 본 논문에서는 IS2000 1x의 수신 신호 모델링, 빔형성 알고리즘, 빔형성 모듈 설계 및 테스트 베드를 이용한 성능 분석을 하였다. 수신 성능을 높이는 최적의 빔형성을 위해 빔형성 알고리즘은, Lagrange 공식을 이용한 Generalized Lagrange 알고리즘을 이용하였다. 이를 신호처리 칩을 이용한 보드로 직접 설계, 제작하였다. 빔형성 모듈에 대한 성능시험 결과 정상동작 확인 및 실시간 동작처리가 가능함을 보였다. 따라서 본 논문에서 제시한 스마트 안테나 Test-bed는 IS2000 이동통신 환경에서 우수한 성능을 나타낼 수 있음을 증명하였다.

• 한국통신학회논문지
• /
• 제22권3호
• /
• pp.532-538
• /
• 1997

Exactly aclculated antenna factors are requeired for determining EMI levels in an actual radiated emission test. In this paper, the antenna factors of short dipole antennas above the ground plane are calculated theoretically for the antenna with Roberts balun specified ANSI C63.5 regulation. Also treated is a half-wavelength dipole antenna with Roberts balun to compare the antenna factors with those of resonant dipole antenna. In formulationof antenna factors the antenna is treated as the boundary value problem of Maxwells equations and is analyzed by the Galerkins method of moments. The balun is treated using circuit theory based on power transmission mismatch.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.35-38
• /
• 2005

The Objective of this work was to design Composite Antenna Structures (CAS) and investigate impact behavior of CAS which was various curvature. This term, CAS, indicates that structural surface becomes antenna. Constituent materials were selected considering electrical properties, dielectric constants and tangent loss as well as mechanical properties. For the antenna performance, microstrip antenna layers inserted into structural layers were designed for satellite communication at the resonant frequency of 12.5 GHz and final demonstration article was. After making five kinds of curved CAS, which radii of curvature are flat, 200, 150, 100, 50 mm. The antenna performance changed in accordance with variation of curvature. The Reflection coefficient was independent of curvature but the gain decreased with the radius of curvature. The impact test equipment was Dyna-8250 drop weight tester. The impact characteristic in accordance with curvature is maximum absorb energy is same each other. The impact energy was 8.5 J. For various Impact energy test, five energy levels 3 J, 5 J, 7 J, 10 J, 20 J were used. The performance of impact damaged antenna was estimated by measuring the return loss and the radiation pattern. It was revealed that the performance of antenna was not related to the impact damage. Because the impactor did not damage the patch directly. CAS have good impact stability for the antenna performance.

• 한국군사과학기술학회지
• /
• 제4권1호
• /
• pp.124-136
• /
• 2001

In this paper, we designed and manufactured the Ku-band circular waveguide antenna to do wireless communication with a ground radar as on-board antenna of missile. Using the MATLAB and the HFSS, we designed the circular polarizer which has a characteristic of circular polarization and broadband using the capacitive pin method, the feeder to feed coaxial line to circular waveguide, and a stopper to prevent a conductor material from being inserted. Then we simulated the designed antenna using the HFSS, obtained the gain and the radiation pattern. Because of a difficulty of manufacture, we established a manufacture process procedure. Antenna is manufactured with this procedure, test results of the manufactured antenna are the axial ratio of 1.37 ~ 1.72, the 3 ㏈ beamwidth of $72.23^{\circ}{\sim}78.54^{\circ},$ and the gain of 3.26 ~ 4.61 ㏈ within frequency band. We knew that these results are similar with simulation results. Also, we confirmed that the manufactured antenna is satisfied with requirement conditions through performance test, environmental test and flight test.

• 한국정보전자통신기술학회논문지
• /
• 제9권6호
• /
• pp.534-538
• /
• 2016

This paper discusses the characteristics and effects of dielectric inner-supports on discone antenna for broadband RF test chamber, and the verification has been performed by simulation. Several design parameters such as the thickness of the gap support, the position of the side support, and the thickness of the side support has been analyzed. The thickness of the gap support affected the reflection coefficient. An effect of the offset of the side support from the center was slight below 3 GHz and significant above 3 GHz. The thickness of the side support did not affect the reflection coefficient or the gain much. The performance of the fabricated discone antenna was in good agreement with the simulated results. This investigation of a dielectric support effects could be used to design a commercial discone antenna for broadband RF test chamber, focusing on electrical performance and mechanical stability.

• 한국통신학회논문지
• /
• 제24권8B호
• /
• pp.1456-1463
• /
• 1999

본 논문은 한국표준과학연구원의 야외시험장에서 표준안테나법을 이용하여 안테나인자측정 시스템에 관하여 기술하고 주변 잡음이 안테나인자에 미치는 영향을 줄이기 위한 방법에 대해 논한다. 측정주파수의 범위는 30~1000 MHz이며, 모든 제어와 데이터 수집은 컴퓨터를 이용하여 자동화 하였다. 측정한 안테나인자를 나타내었고, 안테나인자의 총 측정불확도는 $\pm$1 dB 이다.

• 한국전자파학회논문지
• /
• 제18권2호
• /
• pp.166-176
• /
• 2007

측정 분야나 교정 분야에서 측정 불확도를 보고하는 것은 매우 중요하다. 정보통신부 전파연구소에서는 EMI 측정 시험소를 위하여 안테나 교정 서비스를 제공하고 있는데, 안테나 교정의 정확성은 측정 불확도 평가로 집약되어, EMI 시험의 신뢰성을 판가름하는 시금석이 된다. EMI에 관한 국제기구인 CISPR에서는 2005년 말에 안테나 교정에 대한 최초의 표준 초안인 CISPR/A/644/C를 내놓았다. 이 초안은 안테나교정 및 관련된 측정 불확도를 포함하고 있다. 본 논문에서는 이 문서를 근간으로 전파연구소 이천의 안테나 교정시험장에서 EMI용 다이폴안테나를 교정할 때의 측정 불확도를 산출하였다. 전파연구소의 안테나 교정 방법은 자유 공간 안테나 인자를 측정하는 3-안테나의 height scanning averaging 법으로서, 본 방법에 의하여 안테나가 교정될 때 측정 결과에 영향을 미칠 수 있는 모든 불확도 요인을 고려하였다.

• 전기전자학회논문지
• /
• 제16권4호
• /
• pp.290-296
• /
• 2012

본 논문에서는 반무반사실내에서 반사체와 시간영역 측정을 이용한 반사파의 효과적인 억제 기술을 제안하고 있다. 제안한 기법을 이용하여 측정 영역상에 전기장의 균일도를 향상시켜 완전 무반사실과 유사한 안테나 측정환경을 구현할 수 있었다. 구현한 측정환경의 성능은 측정을 통하여 검증하였으며 소형 VHF대역 안테나 측정에 사용 가능할 것으로 판단된다.

• 정보통신설비학회논문지
• /
• 제2권1호
• /
• pp.78-87
• /
• 2003

One of the most difficult and important problems associated with radiated electromagnetic emissions from digital devices are the determination of antenna factor and site acceptability of an open area test site. This paper presents the problems of the open area test site and EMC antennas far measuring electromagnetic interferences radiated from the equipements. It seems desirable that the antenna factor of EMC antennas be revised to the antenna factor with zero reflection presented in this paper for accurate measurements.