• 수산해양기술연구
• /
• 제28권1호
• /
• pp.53-60
• /
• 1992

In this study, cathodic protection experiment was carried out by Al-alloy sacrificial anode in marine environments which have specific resistance($\rho$) if 25~7000$\Omega$.cm and investigated protection potential, current density and loss rate of Al-alloy sacrificial anode. The main results resistance($\rho$) of 400$\Omega$.cm, the cathodic protection potential appears high about-720 mV(SCE). But below specific resistance($\rho$) of 300$\Omega$.cm, the cathodic protection potential appears low about-770 mV(SCE) and simultaneously, cathode is protected sufficiently. 2) The loss rate of Al-Alloy sacrificial anode became large with decreasing specific resistance and increasing the ratio(A sub(c)/A sub(a) of bared surface area of anode and cathode. 3) The loss rate of Al-alloy sacrificial anode(w) to the mean current density of anode(i) is as follows. w=ai+b (a, b : experimental constants)

• Corrosion Science and Technology
• /
• 제11권4호
• /
• pp.112-119
• /
• 2012

This paper presents the results of a study of the effectiveness of cathodic protection with insoluble ICCP anode in reinforced concrete structures. Experimental tests were carried out on reinforced concrete specimens with 3 different commercial anodes for ICCP system in order to compare the effectiveness of cathodic protection. Results have shown that the kinds of anode for ICCP is irrelevant to the effectiveness of cathodic protection, In case of ICCP, the performance of cathodic protection has no relationship to the kinds of anode especially in concrete specimens with sea water condition. It has been found slightly more effective at Ti-Rod anode in fresh water condition and Ti-Mesh anode in atmospheric condition.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1079-1081
• /
• 2006

Optical and electrical properties of various transparent conducting oxides (ITO, AZO, ITO/Ag/ITO, AZO/Ag/AZO) were investigated for anode of OLED display. ITO/Ag/ITO multi-layer anode has much better electrical and optical characteristics than other films, and OLED on that anode showed lower threshold voltage and better luminescence.

• 대한전자공학회논문지
• /
• 제11권2호
• /
• pp.40-45
• /
• 1974

SCR에서도 anode 전류가 미소(약수 10mA∼수100mA이내)할때에는 게이트 전fur을 조정하므로써 anode전류를 조절할수 있다. 이를 이용하여 cathode 각로에 적당치의 저항을 삽입하여 게이트 회로에 부성저항특성을 나타내게 할 수 있고 간단한 정형파 발진회로를 만들었다.

• 한국전기전자재료학회논문지
• /
• 제19권7호
• /
• pp.687-694
• /
• 2006

We report on the fabrication of organic-based flexible displays using an amorphous IZO anode grown at room temperature. The IZO anode films were grown by a conventional DC reactive sputtering on the polycarbonate (PC) substrate at room temperature using a synthesized IZO target in a $Ar/O_2$ ambient. Both x-ray diffraction (XRD) and high resolution electron microscope (HREM) examination results show that the IZO anode film grown at room temperature Is complete amorphous structure due to low substrate temperature. A sheet resistance of $35.6\Omega/\Box$, average transmittance above 90 % in visible range, and root mean spare roughness of $6\sim10.5\AA$ were obtained even in the IZO anode film grown on PC substrate at room temperature. It is shown that the $Ir(ppy)_3$ doped flexible organic light emitting diode (OLED) fabricated on the IZO anode exhibit comparable current-voltage-luminance characteristics as well as external quantum efficiency and power efficiency to OLED fabricated on conventional ITO/Glass substrate. These findings indicate that the IZO anode film grown on PC substrate is a promising anode materials for the fabrication of organic based flexible displays.

• Carbon letters
• /
• 제8권3호
• /
• pp.207-213
• /
• 2007

The properties and electrochemical characteristics of anode material using pitch-coated graphite residue compounds by heat-treatment at $600^{\circ}C$ for 1 hour were investigated. The distance of layers of pitch-coated graphite residual compounds was 3.3539 ${\AA}$, which was as same as that of graphite. Its electrochemical and charge discharge characteristics were tested according to different four types of carbon material, natural graphite, pitch-coated graphite, amorphous graphite and pitch-coated graphite residual compounds, respectively. So it was shown the best charge-discharge characteristics in all of the samples. For the electrochemical and charge-discharge characteristics, although pitch-coated graphite residual compounds had different carbon contents 70% and 80%, these two samples were shown good electrochemical and charge-discharge characteristics.

• 한국재료학회지
• /
• 제10권10호
• /
• pp.659-664
• /
• 2000

연료극 지지체식 원통형 고체산화물 연료전지를 개방하기 위해 연료극 지지체와 전해질이 코팅된 연료극 원통관의 제조 및 그것의 특성에 대해 연구하였다- 연료극 지지체는 20-50vol.%의 탄소함량에 따라 만들어졌으며, 탄소량이 증가함에 따라 연 료극 지지체의 기공율도 점차 증가하였으며, 적절한 기공율을 가지기 위한 최적 탄소량은 30vol.%임을 확인하였다. 연료극 지지체 관은 압출법으로 제작하였으며, 전해질은 슬러리 코팅법으로 원통판의 바깥쪽에 코팅하였고, $1400^{\circ}C$에서 공소결을 성공적으로 실시하였다. 소결후 물리척특성과 미세구조를 조사하였으며, 연료극 지지체관의 기공율은 35%이었고 연료전지의 요구조건을 만족하였다. 기체투과율 시험을 통하여, 연료극 지지체관 자체는 충분히 다공성을 나타내었으나, 전해질층을 코팅한 경우에는 매우 낮은 기체부과율을 나타냄을 확인하였다. 이것은 코팅된 전해질층이 매우 치밀하다는 것을 의미하며, 본 연구를 통해서 연료극 지지체식 원통형 고체산화물 연료전지가 제조될 수 있음을 확인하였다.

• Korean Chemical Engineering Research
• /
• 제56권4호
• /
• pp.561-567
• /
• 2018

본 연구에서는 리튬이온전지 실리콘 음극소재의 사이클 안정성 향상을 위해 실리콘/탄소 음극소재의 전기화학적 특성을 조사하였다. Tetraethyl orthosilicate (TEOS) 로부터 스토버법 및 마그네슘 열 환원법을 통하여 다공성 실리콘을 제조하고, 제조된 다공성 실리콘과 피치의 질량비에 따라 실리콘/탄소 음극소재를 제조하였다. 실리콘/탄소 음극소재의 물리적 특성은 XRD와 TGA를 통해 분석하였다. 1.0 M $LiPF_6$ (EC : DEC = 1 : 1 vol%) 전해액에서 실리콘/탄소 음극소재의 충 방전 사이클, 율속, 순환전압전류, 임피던스 테스트를 통해 전기화학적 특성을 조사하였다. 제조된 실리콘/탄소 음극소재 실리콘 : 탄소 = 5 : 95 일때 453 mAh/g의 향상된 용량을 나타내었으며, 사이클 성능 또한 두 번째 사이클 이후 30 사이클까지 매우 우수한 사이클 안정성을 나타냄을 확인하였다.

• 한국연소학회지
• /
• 제15권3호
• /
• pp.8-14
• /
• 2010

Fuel processing systems which convert fuel into rich gas (such as stream reforming, partial oxidation, autothermal reforming) need high temperature environment ($600{\sim}1,000^{\circ}$). Generally, anode-off gas or mixture of anode-off gas and LNG is used as input gas of fuel reformer. In order to make efficient and low emission burner system for fuel reformer, it is necessary to elucidate the combustion and emission characteristic of fuel reformer burner. The purpose of this study is to develop a porous premixed flat ceramic burner that can be used for 1~5 kW fuel cell reformer. Ceramic burner experiments using natural gas, hydrogen gas, anode off gas, mixture of natural gas & anode off gas were carried out respectively to investigate the flame characteristics by heating capacity and equivalence ratio. Results show that the stable flat flames can be established for natural gas, hydrogen gas, anode off gas and mixture of natural gas & anode off gas as reformer fuel in the porous ceramic burner. For all of fuels, their burning velocities become smaller as the equivalence ratio goes to the lean mixture ratio, and a lift-off occurs at lean limit. Flame length in hydrogen and anode off gas became longer with increasing the heat capacity. In particular, the blue surface flame is found to be very stable at a very lean equivalence ratio at heat capacity and different fuels. The exhausted NOx and CO measurement shows that the blue surface flame represents the lowest NOx and CO emissions since it remains very stable at a lean equivalence ratio.

• 한국의학물리학회지:의학물리
• /
• 제27권4호
• /
• pp.272-276
• /
• 2016

To investigate the optimum x-ray tube design for the dental radiology, factors affecting x-ray beam characteristics such as tungsten target thickness and anode angle were evaluated. Another goal of the study was to addresses the anode heel effect and off-axis spectra for different target angles. MCNPX has been utilized to simulate the diagnostic x-ray tube with the aim of predicting optimum target angle and angular distribution of x-ray intensity around the x-ray target. For simulation of x-ray spectra, MCNPX was run in photon and electron using default values for PHYS:P and PHYS:E cards to enable full electron and photon transport. The x-ray tube consists of an evacuated 1 mm alumina envelope containing a tungsten anode embedded in a copper part. The envelope is encased in lead shield with an opening window. MCNPX simulations were run for x-ray tube potentials of 70 kV. A monoenergetic electron source at the distance of 2 cm from the anode surface was considered. The electron beam diameter was 0.3 mm striking on the focal spot. In this work, the optimum thickness of tungsten target was $3{\mu}m$ for the 70 kV electron potential. To determine the angle with the highest photon intensity per initial electron striking on the target, the x-ray intensity per initial electron was calculated for different tungsten target angles. The optimum anode angle based only on x-ray beam flatness was 35 degree. It should be mentioned that there is a considerable trade-off between anode angle which determines the focal spot size and geometric penumbra. The optimized thickness of a target material was calculated to maximize the x-ray intensity produced from a tungsten target materials for a 70 keV electron energy. Our results also showed that the anode angle has an influencing effect on heel effect and beam intensity across the beam.